OLIGHT O’Pen Glow Rechargeable Penlight User Manual

OLIGHT O’Pen Glow Rechargeable Penlight

Product Information

The product is a rechargeable penlight that comes with a charging base, magnetic clamp, pen ink, and a Type-C charging cable. The penlight has a white pen clip light and a white pen tip light with different CCT values of 5700K and 4000K, respectively. It has four different brightness modes – high, medium, low, and moon – with lumen values of 120, 60, 20, and 5, respectively. The pen tip LED has a brightness of 0.2 lumens. The product also features a laser with a maximum output of 0.39mW (Class 1) and a laser wavelength of 510-530nm. The product dimensions are (L)155(D)12.7mm or (L)6.10(D)0.5in, and it weighs 38g or 1.34oz. The product has Lithium Polymer batteries with a capacity of 0.407Wh (110mAh / 3.7V).

Product Usage Instructions

1. To recharge the product, retract the pen ink and insert the pen directly into the charging base.
2. The charging base uses Type-C charging with an input of 5V and a maximum charging current of 200mA. It takes about 55 minutes to fully charge the product.
3. When the product is inserted into the charging base for recharging, the pen ink needs to be retracted.
4. When the product is fully charged, the green light on the charging base will be on, and it will turn off.
5. To turn on/off the pen clip LED, press and hold the button for more than one second.
6. To switch to high mode, double press the button.
7. To adjust the brightness, press and hold the button for one second.
8. To turn on/off the pen tip light, extend the pen ink and press the button once.
9. To switch between moonlight, low, medium, and high modes, extend the pen ink and press the button multiple times.
10. To lock the product, press and hold the button for more than two seconds.
11. To unlock the product, press and hold the button for more than one second.

IN THE BOX

Multi-language dictionary

• Press
• Double press
• Press and hold
• Push
• Push and hold
• Retract the pen ink
• Extend the pen ink

Product specification

• Above data are tested per ANSI/NEMA FL 1-2009 standard in Olight’s labs for reference. The tests are performed indoors under a room temperature of 25 degrees celsius with windless conditions. The runtime may vary depending on the external temperature and ventilation conditions, and these biases may affect the results of testing.
• In order to ensure an even light when writing, the pen tip adopts a soft light design; a certain amount of light loss exists, so the running time is shortened.

Charging base-related parameters

• Charging Method Retract the pen ink, then insert the pen directly into the charging base to recharge.
• Max. Charging Current 200mA
• Input Type-C (5V)
• Output CC&CV
• Time to Fully Charge About 55 mins

Operating instructions below

1. Charging base charging
2. Lockout
3. Unlock
4. Pen clip light ON/OFF
5. High mode
6. Change brightness
7. Pen tip light ON
8. Pen tip light OFF
9. Laser light ON/OFF
10. Turn on the pen clip light when the pen tip light is on
11. Turn on the pen tip light when the pen clip light is on
12. Turn off both the pen tip light and the pen clip light simultaneously
13. Replace the pen ink

Note:

1. When the product is inserted into the charging base for recharging, the pen ink needs to be retracted.
2. When the product is fully charged, the green light will be on, it will turn off after 10 minutes of continuous lighting. The light will not turn on if no pen is inserted into the charging base.
3. When the lock mode is on, a quick press on the tail button will cause the pen clip light to instantly turn on and alert the user.
4. As the pen ink is a conductive part, it is tightly fixed at the tail end. When replacing the pen ink, please insert the new pen ink forcefully into the guide sleeve of the pen body and ensure that it is inserted into the bottom.
5. If the pen plunger does not move smoothly after replacing the pen ink, please check whether the pen ink is installed properly.
6. If the product gets wet, please take out the pen ink quickly and dry the water on the pen ink to prevent it from rusting and affecting the pen tip light and the charging function.
7. Laser and white light cannot be used simultaneously.

WARRANTY

• Within 30 days of purchase: Contact the original seller for repair or replacement.
• Within 2 years of purchase: Contact Olight for repair or replacement.
• Warranty for the charging base: 2 years

For any of the fragile or low-value fittings not covered above, like lanyard and clip, you can contact the post-sale within 30 days of the purchase, if it has any quality drawback or damage under normal use condition. If such drawback or damage occurs after 30 days of the purchase or under abnormal use condition, we will only offer conditional quality assurance as appropriate.

USA Customer Support: cs@olightstore.com
Global Customer Support: contact@olightworld.com
Visit www.olightworld.com to see our complete product line of portable illumination tools.

References

• Olight | Illuminate Your World.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>