InCarTec 29-CTSNS011 Nissan Steering Wheel Control Interface User Guide
- June 10, 2024
- InCarTec
Table of Contents
InCarTec 29-CTSNS011 Nissan Steering Wheel Control Interface
Product Information
Nissan Steering Wheel Control Interface
The 29-CTSNS011 Nissan Steering Wheel Control Interface is designed for use
with the following Nissan vehicles: Qashqai (J11, Acenta Only) 2014>, X-Trail
(T32) 2014>, Pulsar 2015>, Titan 2015>, Micra 2017> (For Vehicles without
Parking Sensors or Reverse Camera). The interface is used to retain the OEM
Aux Socket (If feature is available).
Wiring Colour Codes
| Wire Colour | Function |
|---|---|
| Yellow | Permanent 12V |
| Black | Ground |
| Red | 12V Ignition |
| Orange | Illumination |
| Green | Park Brake |
| Pink | Speed Pulse |
| Purple | Right Rear Speaker + |
| Purple/Black | Right Rear Speaker – |
| Green | Left Rear Speaker + |
| Green/Black | Left Rear Speaker – |
| Grey | Right Front Speaker + |
| Grey/Black | Right Front Speaker – |
| White | Left Front Speaker + |
| White/Black | Left Front Speaker – |
Setting Vehicle Time
Press and hold ‘Enter’ for 8 seconds (Micra – set the MDF to Aux and hold
the button for 8 seconds). Use Track – to change hours and Track + to change
minutes. Short press Enter to set the time, or press and hold Enter to exit
the menu without saving changes.
ABOUT THIS PRODUCT
29-CTSNS011
Nissan Steering Wheel Control Interface. Retains OEM Aux Socket (If feature is
available).
Product Contents
- Interface
- Harness
- Instruction
Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for
installa-tion. The place of installation must be free of moisture and away
from heat sources. Please ensure you use the correct tools to avoid damage to
the vehicle or product.
Wiring Colour Codes
| Wire Colour | Function |
|---|---|
| Yellow | Permanent 12V |
| Black | Ground |
| Red | 12V Ignition |
| Orange | Illumination |
| Green | Park Brake |
| Pink | Speed Pulse |
| Purple | Reverse |
| Wire Colour | Function |
| --- | --- |
| Purple | Right Rear Speaker + |
| Purple/Black | Right Rear Speaker – |
| Green | Left Rear Speaker + |
| Green/Black | Left Rear Speaker – |
| Grey | Right Front Speaker + |
| Grey/Black | Right Front Speaker – |
| White | Left Front Speaker + |
| White/Black | Left Front Speaker – |
Fitting Guide
-
Remove and disconnect the original head unit.
-
Connect the 12 way molex connector of the head unit patch lead (supplied separately) to the interface.
-
Connect the opposite end of head unit patch lead to the head unit steering wheel control input on the back of the aftermarket head unit. This may be a 3.5mm jack plug or a wire input depending upon the head unit brand being fitted. Please see the head unit installation manual for further information on where to connect.
Important Note: This step must be completed before connecting power to the interface. Failure to so do may result in no steering wheel control function. -
Connect the 14 way molex connector to the interface.
-
Connect the male power/speaker ISO harness to the female power/speaker ISO harness from the aftermarket head unit. For aftermarket head units without an ISO connector, please refer to the wiring colours on Pg. 2.
-
Connect the female vehicle specific connector to the male vehicle connector and connect the USB and red/white aux connections to the head unit to retain these features (if vehicle is equipped).
STEERING WHEEL CONTROL FUNCTIONS
- Track -: Setting Vehicle Time
- Track +: Press and hold ‘Enter’ for 8 seconds (Micra – set the MDF
- Volume – : to Aux and hold the button for 8 seconds). Use Track – to
- Volume + : change hours and Track + to change minutes. Short press
- Pick Up: Enter to set the time, or press and hold Enter to exit the menu
- Hang Up: without saving changes.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>