HitLights ‎L1012V-MC1 LED Strip Lights User Manual

HitLights ‎L1012V-MC1 LED Strip Lights

Welcome To LED Strip Lighting

Our thin and flexible LED lighting can be used in nearly and space to create wonderful accents of stylish light just about anywhere! Our high-quality LED chips provide exceptional light output, color accuracy, and brightness; and will be sure to establish a comfortable lighting effect for your project! Because they are fully dimmable and run on very low amounts of power, our LED light strips are designed to be an extremely versatile lighting solution.

Common uses for our LED Light Strips include task lighting and accent lighting:

• Indirect lighting for recessed coves and molding
• Display cases, shelves, etc.
• Over, inside, and under cabinet areas
• Perimeter lighting for counters and shelves
• Custom lighting for artwork and other projects

In general, LED Strip Lights provided an easy DIY task for most customers, but basic wiring skills such as stripping, splicing, extending, and connecting wires are usually required for custom installations.

Eclipse Kit

Your kit should include the following parts

• 4*1ft Eclipse LED Strip light
• 1° UL Power Supply
• 4′ 1ft 4-pin Strip-to-Strip Connectors
• 2-Controller Fixing Tane
• 1° RF Receiver
• 1° RF Remote
• 8° Wire Holding Clips

Warning

1. Be careful not to damage the strip or other components. Avoid contact with strong chemicals or cleaning products. Sharp objects. or unwanted electrical sources including static electricity.
2. Avoid bending your strip at sharp angles, as this can damage the strip over time.
3. Do not attach the strip to conductive or metal surfaces – and be sure that the surface you’re installing on does not contain potentially conductive objects such as nails or screws.
4. LED strip light can be cut by segment, but we don’t recommend it, since segmenting it can cause the strip to be unstable. If it’s required, please prepare the connectors, and make sure the tooth of the connectors is being pressed flush onto the metal pad of the strip light during the connection

Important Notices And Concerns

• This product must only be powered by a 12V DC power source.
• Unplug your power source when cutting LED strips.
• Pay close attention to the polarity of all connections: match positive to (+) and negative to (-).
• This strip is rated as IP-65, and it should be installed in dry or damp indoor locations. Not recommended for outdoor use.
• Be sure to follow local and national electrical codes for low-voltage Class 2 power units.

Steps For More Advanced Installations

12V DC Voltage Drop: 12V DC power is naturally subject to “voltage drop.” Along the length of 12V power wires through the lighting, LED chips may begin to dim after connecting more than 1 spool of this LED light strip. This can be corrected with the use of RGB amplifiers.

Connecting Your Led Light Strip

1. Before formally installed in the designated location, please connect the strip lights to the receiver and power supply, then connect the power supply to the power source to test and verify your LED strip lights are in working order.
2. Use the included alcohol pad to clean the location where you plan to adhere your strip, making sure no dust or dirt remains prior to installation. (Some surfaces may not be suitable for this tape (e.g., brick, fabric, or other rough surfaces).
3. Carefully remove the blue release liner protecting the surface of the LED Strip’s adhesive. Press and hold the LED light strip along the installation location. Make sure there are no gaps between the lights and the surface.
4. Connect the led strip light to the receiver, then to the power supply. Make sure that the arrow on the 4 PIN connectors matches the arrow on the strip light. The ~ arrows at both ends need to correspond positively.)
5. Use the included foam tape to mount the receiver, and the included wire clips to keep the wire connectors in place.
6. Connect your power supply to your power source – your strips should light up!

Controller

1. Turn On
2. Turn Off
3. Auto mode
4. Speed adjust +
5. Speed adjust –
6. Modes switch +
7. Modes switch –
8. Brightness adjust +
9. Brightness adjust

Functions

• 1/2. Turn On/off  /
  Turn the unit on/Off. When powered on, the unit will restore the previous status setting.

• Auto mode
  Automatically plays 19 dynamic modes in a loop.

• 4/5. Speed adjust
  S+ to increase speed, S- to decrease. This key only works in dynamic mode.

• 6/7. Dynamic modes switch /
  Switch between 19 dynamic modes.

• 8/9. Brightness adjust
  Press to increase brightness and decrease.

Modes List

• Static Color Mode: (Red], [Green], [Blue], [Purplish Red], [Light Green], [Light Blue]. [Orange], [Purple], [Cyan], [yellow], [Lavender], [White]
• Dynamic Mode: [Red fade], [Green fade], [Blue fade], [Yellow fade] [Purple fade], [Cyan fade], [White fade], [Red fade+ jump] [Green fade+ jump], [Blue fade + jump], [Red flash], [Green flash]. [Blue flash], [3 colors jump], [7 colors jump]. [3 colors alternating flash], [Dazzling mode] [3 colors fade], [7 colors fade]

Operation

1. Using Remote Controller
   Remove the Plastic tab before using. Remote signals can pass through many barriers. To properly receive the remote signal, do not install the main unit within enclosed metal parts.

2. Paring New Remote
   Remote is paired to the receiver by default. A receiver can be paired with 2 remotes. Remotes can be paired to any receiver. If a receiver is paired to 3 remotes, the 3rd remote will cover the 1st. Follow the steps below to pair a new remote.

• Disconnect the receiver from power, and reconnect within 5 sec.
• Press “ ****” for 2 seconds and the receiver will recognize the new remote controller

We Are Happy To Help

LED Strips may seem complicated at first glance, especially to beginners, but please do not worry! Contact us, we will answer any questions you may have and talk you through the process of creating professionally graded led lighting for your projects. 1.855.768.4135

Customer Support

customerservice@hitlights.com

FAQ’s

How long is the HitLights L1012V-MC1-0465-ECLBK-K LED Strip Lights?

The LED strip lights are typically available in different lengths, such as 16.4 feet (5 meters) or longer. Refer to the product specifications or packaging for the specific length of the LED strip lights you have.

Can I cut the LED strip lights to a shorter length?

Yes, the HitLights LED strip lights can be cut at designated cutting points. This allows you to customize the length of the strip to fit your desired application.

What is the voltage requirement for the LED strip lights?

The HitLights LED strip lights typically operate at 12 volts (DC). It's important to ensure that the power supply or adapter you use matches this voltage requirement.

Are the LED strip lights dimmable?

Yes, the HitLights LED strip lights are generally dimmable. However, this depends on the specific model and any additional dimming accessories or controllers that may be required.

Can I control the LED strip lights remotely?

Some models of HitLights LED strip lights may support remote control functionality. This usually requires the use of a separate remote control or a compatible smart home system.

Are the LED strip lights waterproof?

HitLights offers a variety of LED strip lights, including both waterproof and non-waterproof options. Check the product specifications or packaging to determine if the specific model you have is waterproof.

Can I connect multiple LED strips together?

Yes, it is often possible to connect multiple HitLights LED strips together to create longer lengths or cover larger areas. However, be sure to follow the manufacturer's instructions for proper connection methods and consider any limitations on maximum length.

Are there color options available?

HitLights LED strip lights are available in different color options, including single-color (e.g., white, warm white) and multi-color (RGB) variants. Check the product details or packaging for the specific color options of the LED strip lights you have.

Can I use the LED strip lights outdoors?

Some models of HitLights LED strip lights are suitable for outdoor use, while others are designed for indoor use only. Verify the IP rating or waterproofing capabilities of the specific LED strip lights you have to determine their suitability for outdoor applications.

Is installation hardware included with the LED strip lights?

HitLights LED strip lights typically come with adhesive backing for easy installation. However, the availability of additional installation hardware, such as mounting clips or brackets, may vary depending on the specific package or product variant.

Video – Introduction

Download this PDF Link:HitLights ‎L1012V-MC1 LED Strip Lights User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>