FOREVER Multi-Trans Hard Surface Paper Instructions
- June 4, 2024
- FOREVER
Table of Contents
FOREVER Multi-Trans Hard Surface Paper
PRINT SETTINGS FOR OKI WHITE TONER PRINTERS
- Paper & Print: Transparency, Multi-Purpose Tray
- White Toner Density: +3 (Calibration at the printer panel)
- Image Mode: mirror image
PRINT SETTINGS FOR OKI Pro8432WT
- Paper & Print: User Type 1, Multi-Purpose Tray
- White Toner Density: +3 (Calibration at the printer panel)
- Color Paper Settings: +2 (Set at the printer panel)
PRINT SETTINGS FOR CMYK PRINTERS
Only for light colored mugs Paper & Print: Transparency (Film/Foil) or similar
TRANSFER PROCESS
- Preheat your mug press before use.
- Position & fix the printed image to the mug using a heat resistant tape.
- Put the mug in the press.
- Press by using the settings below.
- IMPORTANT : The timer of the mug press should not start until the mug has reached the set temperature.
- If your press does not do this automatically, increase the press time to 4 minutes!
- Cool the mug down by dipping into cold water.
- Make sure the transfer media is soft before peeling.
- ATTENTION : At this point, the mug is very hot. Take precautions when moving the mug.
SETTINGS MUG PRESS
- MUG MUG PRESS
- WHITE & COLORED MUGS 140°C / 284°F • 180 sec • high pressure
TIPS & TRICKS
- The light marks that may appear after the application process, can be easily removed with Isopropanol.
- Using the Mug Press Silicone Pad helps distribute the heat evenly around the whole mug & transfer. The pressing parameters can vary by using a silicone pad.
- If you put the mug in the oven at 160°C / 320°F for 15 minutes the scratch resistance will be better.
PRINT SETTINGS FOR OKI WHITE TONER PRINTERS:
- Paper & Print: Transparency, Multi-Purpose Tray
- White Toner Density: +3 (Calibration at the printer panel)
- Image Mode: mirror image
PRINT SETTINGS FOR OKI Pro8432WT:
- Paper & Print: User Type 1, Multi-Purpose Tray
- White Toner Density: +3 (Calibration at the printer panel)
- Color Paper Settings: +2 (Set at the printer panel)
PRINT SETTINGS FOR CMYK PRINTERS:
Only for light colored mugs Paper & Print: Transparency (Film/Foil) or similar
TRANSFER PROCESS
- Set the temperature of the transfer press to 200°C / 390°F.
- Place the substrate on the lower plate.
- Place the transfer paper on the substrate and cover both with the a silicone pad with 5mm thickness.
- Place the sensor of the digital thermometer between the transfer paper and the substrate. (Relevant is the temperature on the surface of the substrate which is shown through the digital thermometer.
- The printing time depends on the size (mass) of the substrate.)
- Open the transfer press when the below mentioned temperature is achieved and peel off the transfer paper as indicated below.
- ATTENTION : At this point, the material is very hot. Take precautions when moving it.
SETTINGS HEAT PRESS
SURFACE| AUTOMATIC HEAT PRESS| PREHEATING| OPENING
AT| PEELING| FIXING
---|---|---|---|---|---
ALUMINIUM| 4-5 bar (55-70 PSI)| | 120°C (250°F)|
Warm or cold| 60 sec.
ADHESIVE FILM| 4-5 bar (55-70 PSI)| | 130°C (265°F)|
Let cool down for 5-10 sec.|
CHROMOLUX BINDER| 3-4 bar (40-60 PSI)| 10 seconds|
100-110°C (210-230°F)| Warm or cold|
CERAMIC TILE| 4-5 bar (55-70 PSI)| | 130°C (265°F)|
Warm or cold| 60 sec.
WOOD| 3 bar (40 PSI)| 20 seconds| 130°C (266°F)|
Immediately| 60 sec.
MAGNETIC VINYL| 4-5 bar (55-70 PSI)| | 110-120°C
(230-250°F)| Warm or cold| 60 sec.
ACRYLIC GLASS| 4-5 bar (55-70 PSI)| | 100-105°C
(210-220°F)| Let cool down for 5-10 sec.|
MIRROR| 4-5 bar (55-70 PSI)| | 145°C (265°F)|
Warm or cold|
MOUSE PAD| 4-5 bar (55-70 PSI)| | 110°C (230°F)|
Warm or cold|
Before starting a mass production, we recommend to make transfer and washing test with all materials.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>