antaira LNP-1002C-SFP-24 Series Industrial Unmanaged PoE Switch Installation Guide
- June 10, 2024
- antaira
Table of Contents
Antaira LNP-1002C-SFP-24 Series Industrial Unmanaged PoE Switch
Antaira Technologies LNP-1002C-SFP-24 Series
The Antaira Technologies LNP-1002C-SFP-24 Series is a 10-port industrial PoE+ unmanaged Ethernet switch that comes with 810/100Tx (30W/Port) and 2Gigabit Combo Ports (210/100/1000Tx RJ45 and 2100/1000 SFP Slots). It has a power input of 12~55VDC and is equipped with one 6-pin removal terminal block connector for dual DC power inputs. The switch also has LED indicators for Power 1, Power 2, Fault, PoE Indicators (Port 1~8), LAN Port 1~8 (Upper LED), LAN Port 1~8 (Lower LED), SFP Port Combo G1~G2, and LAN Port Combo G1~G2.
Package Check List
The package contains the following items:
- 1 – Quick installation guide
- 1 – LNP-1002C-SFP-24(-T)
- 1 – Wall mounting bracket set with screws
- 1 – DC cable –18 AWG & DC jack 5.5 x 2.1mm
- 1 – Dust cover set
Front Panel Layout
Top Panel View
LNP-1002C-SFP-24 series top panel is equipped with one 6-pin removal terminal
block connector for dual DC power inputs (12~55VDC).
Product Overview
System Interface/Performance
- All RJ45 ports support the auto MDI/MDI-X function
- Embedded 810/100Tx (30W/Port) and 2Gigabit combo ports (210/100/1000Tx RJ45 and 2100/1000 SFP slots)
- Store-and-forward switching architecture
- 8K MAC address table
- Jumbo frame supports 9.6K
Power Input & Connection
- DC 12 to 55V redundant power, with a 6-pin removal terminal block
- It is recommended to use a UL listed industrial power supply
Operating Temperature
- Standard operating temperature model: -10°C to 70°C
- Extended operating temperature model: -40°C to 75°C
Case/Installation
- IP30 protection
- DIN-Rail and wall mount design
LED Indicators
Product Usage Instructions
Ethernet Ports
All RJ45 ports are auto-sensing for 10Base-T, 100Base-TX or 1000Base-T device connections. Please follow the wiring pin assignment table below for Ethernet port installation.
| Pins | T568A Color | T568B Color |
|---|---|---|
| Pin 1 | white/green stripe | white/orange stripe |
| Pin 2 | green solid | orange solid |
| Pin 3 | white/orange stripe | white/green stripe |
| Pin 4 | blue solid | white/blue stripe |
| Pin 5 | white/blue stripe | blue solid |
| Pin 6 | orange solid | green solid |
| Pin 7 | white/brown stripe | white/brown stripe |
| Pin 8 | brown solid | brown solid |
Power Input Wiring
To insert the power wire:
- Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts on the terminal block connector.
- Tighten the wire-clamp screws to prevent the wires from loosening.
Industrial Switch Mounting
DIN-Rail Mounting
The DIN-Rail bracket is pre-installed on the industrial Ethernet switch from the factory. To install the industrial switch on the DIN-Rail track:
- Insert the top of the DIN-Rail onto the DIN-Rail bracket.
- Push down on the bottom of the switch until it snaps into place on the DIN-Rail.
- Secure the switch by tightening the DIN-Rail bracket screws.
- Check if the bracket is mounted tightly on the rail.
- To remove the industrial Ethernet switch from the rail, do the opposite from the steps above.
Wall Mounting
Follow the steps below to mount the industrial Ethernet switch using the wall
mounting bracket as shown below in Figure 6.
- Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws.
- Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch.
- Use the screws to screw the wall mounting bracket on the industrial Ethernet switch.
- Use the hook holes at the corners of the wall mounting bracket to hang the industrial Ethernet switch on the wall.
- To remove the wall mount bracket, do the opposite from the steps above.
Field Maintenance and Service
- If the device requires servicing of any kind, the user is required to disconnect and remove it from its mounting. The initial installation should be done in a way that makes this as convenient as possible.
- Voltage/power lines should be properly insulated as well as other cables. Be careful when handling them so as to not trip over.
- Do not under any circumstance insert foreign objects of any kind into the heat dissipation holes located in the different faces of the device. This may not only harm the internal layout, but might cause harm to user as well.
- Do not under any circumstance open the device for any reason. Please contact your dealer for any repair needed or follow the instructions within the manual.
Warranty Policy
Warranty Conditions
Products supplied by Antaira Technologies are covered in this warranty for
sub-standard performance or defective workmanship. The warranty is not,
however, extended to goods damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock,
earthquake
(c) Use of unqualified power supply, connectors, or unauthorized
parts/kits
(d) Replacement with unauthorized parts RMA and Shipping Costs
Reimbursement Customers shall always obtain an authorized “RMA” number from
Antaira before shipping the goods for repair or replacement.
- Within the warranty period (based on the invoice date), all parts and labor are free of charge to the customers.
- Customers are responsible for the cost of parts and labor, if the products are out of warranty.
- For RMA service, customers are responsible for the shipping expense for shipping the RMA unit(s) to Antaira. Antaira is responsible for the shipping expense via a ground service for the return repair/replace unit(s) back to customers.
Limited Liability
Antaira would not be held responsible for any consequential losses from using
Antaira’s product.
Warranty Period
5-Year Warranty
Antaira’s Customer Service and Support
-
Antaira’s Technical Service & Support Centers:
+ 844-268-2472 (Antaira US Headquarter)
+ 48-22-862-88-81 (Antaira Europe Office)
+ 886-2-2218-9733 (Antaira Asia Office) -
Antaira’s Web Sites & Repair/Support Emails:
www.antaira.com / support@antaira.com
www.antaira.eu / info@antaira.eu
www.antaira.com.tw / info@antaira.com.tw
*Any changes will be announced on the Antaira website.
References
- Antaira Technologies | Industrial Networking Solutions
- Antaira Technologies Asia | Industrial Networking Product Solutions
- Antaira Technologies PoE Switches, converters and modules, Bluetooth adapters, servers - Antaira Technologies
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>