datavideo TP-900 PTZ Presentation Prompter User Guide
- June 10, 2024
- Datavideo
Table of Contents
datavideo TP-900 PTZ Presentation Prompter
PARTS
| Item | Description | Quantity |
|---|---|---|
| A | 15” LCD Control Unit | 1 |
| B | 12V universal Mains PSU | 1 |
| C | USB Mouse | 1 |
| D | 5m Ethernet Cable | 1 |
| E | 3.5mm input adapter for WR-500 remote control | 1 |
| F | TP-900 metal base tray with tripod plate | 1 |
| G | 150 x 150 PTZ Scissor Lift | 1 |
| H | Cloth Hood | 1 |
| I | M4 CRV hex tool | 1 |
| J | 9mm long ¼ thumb screw with red dot | 1 |
| K | 9mm long ¼ thumb screw with washers | 1 |
| L | M6*40mm screws | 8 |
| M | M6*14mm screws | 10 |
| N | 16mm long screw | 1 |
| O | 3/8 to ¼ adapter | 1 |
| P | 565mm Vertical extrusions | 4 |
| Q | 475mm horizontal extrusions with 90 degree joining blocks | 2 |
| R | 325mm glass support extrusions with single end caps | 2 |
| S | 250mm PTZ lift extrusions with both end caps | 2 |
| T | 70/30 mirror glass | 1 |
| U | Glass support bar | 1 |
| V | Spare black extrusion end caps | 2 |
| W | Spare M6*14mm screws | 2 |
| X | 12V regulated DTap cable | 2 |
| Y | Small CRV hex tool to remove the tripod plate from item F | 1 |
| Z | Medium CRV hex tool to remove 90 degree joining blocks from item Q | 1 |
ASSEMBLY INSTRUCTIONS
-
Grab TP-900 metal base tray (Item F) and lay flat on surface such as a table.
-
Grab 4x 565mm vertical extrusions (Item P) and 4x M6 14mm screws (Item M)
NOTE: Make sure screw opening closest to the end is facing away from metal base tray (Item
-
Attach the four 565mm vertical extrusions (Item P) to metal base tray (Item F) using the M6 14mm screws (Item M)
Use M4 CRV hex tool (Item I) for this.
-
Grab 2x 475mm Horizontal extrusions (Item Q) & 4x M6 s 14mm screws (Item M). Remove circular cover caps and place aside.
-
Replace the black circular plastic caps
-
Grab 2x 325mm glass support extrusions with sing end caps (Item R) and 4x M6 40mm screws (Item L)
-
Use M4 CRV hex tool (Item I) to attach screws to thevertical extrusions
-
Grab 2x 325mm glass support extrusions (Item R) and 4x M6 14mm screws (Item M)
-
Use M4 CRV hex tool (Item I) to attach screws to the vertical extrusions
-
Top view should look like this.
-
Remove squared black plastic end caps from 1 & 2 extrusion
-
. Remove squared black plastic cap from 1 & 2 extrusion for PTZ
-
Insert the 150 x 150 PTZ scissor lift (Item G) in between the extrusion (1 & 2) as shown above.
-
Ensure that adjustment knob is facing the rear of the teleprompter as shown.
-
Lock the position of the 150 x 150 PTZ Scissor Lift, (Item G) with the 16mm long screw (Item N)
-
Can go up and down by rotating knob
-
With the PTZ Scissor Lift locked, now lay on flat table. Attach / screw quick release plate of your tripod to on to the bottom of the TP-900 metal base plate (Item F)
-
Once installed, mount onto your tripod.
-
Grab glass support bar (Item U) and 2x M6 14mm screws (Item M)
-
Use M4 CRV hex tool (Item I) to attach screws to the vertical extrusions
-
Leave about a quart or an inch of space between glass support bar (Item U) and glass support extrusion (Item R)
-
Grab 70/30 mirror glass (Item T). Carefully remove plastic covering.
-
Place mirror glass carefully in the center.
-
Fasten the space between glass support bar (Item U) and glass support extrusion (Item R) with the M4 CRV hex tool (Item I).
-
Grab the 15” LCD control unit monitor (Item A)
-
Install the 15” LCD Control Unit (Item A) by inserting the 9mm long ¼ thumb screw with red dot (Item J) through the slot in the TP-900 metal base tray with tripod plate(Item F).
-
Now bring the PTZ scissor lift down (Item G)
-
Grab your PTZ camera. (camera not included) and turn upside down to install onto the PTZ scissor lift (Item G).
-
Install your PTZ camera onto PTZ scissor lift (Item G) with thumb screw (Item K)
-
Adjust the position of the 150 x 150 PTZ Scissor Lift (Item G) as required.
Tip: Position the PTZ lens as close to the 70/30 mirror glass as possible to achieve the best range of pan.
-
Grab cloth cover (Item H)
-
Install the Cloth Hood, Item H. The hood is secured to the inside of the TP-900 metal base tray with tripod plate, Item F and Glass support bar, Item U via integral magnets.
The rear of the hood can be expanded if the PTZ camera or cables protrude past the rear of the TP-900 frame.
https://datavideo.com/product/TP-900
References
- Datavideo | Professional end-to-end solutions provider for your live video production.
- TP-900 PTZ Camera Teleprompter | Datavideo | Datavideo | Professional end-to-end solutions provider for your live video production.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>