Riley Hopkins 1616 Riley Flash Dryer Instruction Manual
- June 10, 2024
- Riley Hopkins
Table of Contents
1616 Riley Flash Dryer
Instruction Manual
Tools Required:
- (x1) 1/2” open end wrench • (x1) 7/16” open end wrench
What’s in the box
Tag | Item | Qty. |
---|---|---|
1 | HANDLE-BLACK 1/4-20 INSERT | 1 |
2 | BOLT-1/4-20X1/2HHCS (ZINC) | 1 |
3 | MOUNTING BRACKET BLK | 1 |
4 | HEATER | 1 |
5 | NUT 5/16-18 SERRATED | 8 |
6 | BOLT-5/16-18 X 1-3/4 SERR FL HEX HD ZP | 2 |
7 | TUBE 1.38 DIA | 1 |
8 | TUBE 1.63 DIA | 1 |
9 | COLLAR 1 7/16 ID | 1 |
10 | BENT BOLT | 1 |
11 | GRIP .31 ID X 2.75L | 1 |
12 | LEG | 2 |
13 | BOLT 5/16-18 X 2.5L SERRATED | 2 |
14 | CASTER 2” | 2 |
15 | CASTER 2” W/BRAKE | 2 |
IMPORTANT: BE SURE ALL PARTS ARE ENCLOSED BEFORE ASSEMBLING.
- Assemble mounting bracket [3] and handle [1] using bolt [2].
- Align holes in mounting bracket [3] with holes in tube [7] and secure with two bolts [6] and two nuts [5].
- Place collar [9] at position for desired height and secure with bent bolt [10].
- Assemble legs [12] and tube [8] as shown with legs on flat surface. Secure withbolts [13] and hex nuts [5].
- Secure two casters [14] and two casters [15] to legs [12] using hex nut [5].
- Insert the rotating tube/heater assembly (from Step 3) into the tube [8]. Adjust locking collar [9] to desired height.
- Align face of heater parallel to platen and tighten two bolts [6] and two nuts [5].
General Operating Instructions:
- Adjust height of heater above platen to suit specific conditions.
- Riley Flash will heat to operating temperature in approximately 5 minutes.
- All operating/curing temperatures should be checked with a temperature monitoring device of your choice.
- Pretest all curing situations, inks, and substrates before proceeding.
MANUFACTURE’S WARRANTY
All products are warranted against defects in workmanship at the time of
shipment. The obligation under the above warranty shall be limited to the
repair or replacement of any part or parts manufactured by the dryer
manufacturer without charge F.O.B. factory that may prove defective within 12
months from the date of shipment, which are returned to dryer manufacturer.
The above warranties are the only warranties made with respect to the
equipment. There is no implied warranty of merchantability or of fitness.
EXCLUSIONS: There is no warranty on parts not manufactured by the dryer
manufacturer, other than the respective manufacturer’s warranty, if any. The
warranty against defects shall not extend to damage caused from any of the
following:
- Transport by carrier
- Corrosion
- Operation or use in a manner inconsistent with specifications and/or operating instructions
- Ordinary wear, accident, improper installation, or maintenance
- Alterations made to equipment in any way
Dryer manufacturer shall not be liable for losses or damages, including but not limited to incidental or consequential damages, suffered or incurred because the equipment proves to be defective either upon installation or during its operation or use. Shipment of defective parts to the dryer manufacturer and the return shipment of any repaired or replacement parts from the dryer manufacturer shall be the purchaser’s/user’s expense.
Ryonet Corp. – 800-314-6390 –
www.screenprinting.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>