Skullcandy Push Active Series True Wireless Earbuds User Guide
- June 10, 2024
- Skullcandy
Table of Contents
Skullcandy Push Active Series True Wireless Earbuds
Download the Skullcandy App
Auto Power – On/Off
- Auto On: Open Lid
- Auto Off: Close Lid
Power- On
- Left Earbud or Right Earbud
Power- Off
- Left Earbud or Right Earbud
Pairing
Pairing Mode
- Left Earbud or Right Earbud on Mode
Pair New Device
- “Push Active”
How To Use
Play/Pause Answer/End
- Left Earbud or Right Earbud “While On
Volume Up
- Right Earbud
- “While Audio is Playing
Volume Down
- Left Earbud
- “While Audio is Playing
Share Audio
- Right Earbud – “Share”
- Left Earbud – “Join”
- “While On
Re-Sync Earbuds
- Both Earbuds
- while On
- Bluetooth Disconnected
Find With Tile™
- Both Earbuds
- Tile App Required
Spotify Tap™
- Left Earbud Only
- While On
- Spotify App Required
Reset Paired Device List
- Right Earbud Only
- While ON
- Bluetooth Disconnected
Charging
Charge Earbuds
- Close Lid To Charge
Charge the Case
Voice Control
Skullcandy App Required
- “Hey Skullcandy, Spotify”
- “Hey Skullcandy, Play”
- “Hey Skullcandy, Pause*
- “Hey Skullcandy, Next*
- “Hey Skullcandy, Previous”
- “Hey Skullcandy, Volume Up*
- “Hey Skullcandy, Volume Down”
- “Hey Skullcandy, Stay Aware On*
- “Hey Skullcandy, Stay-Aware Off”
- “Accept”
- “Reject”
Specification
- Speaker Driver: 8mm
- Impedance: 22 Ohma, THD <3%@1KHz
- Voltage Regulation: 5V, 700mA, Bluetooth® 5.2
- Frequenoy Band: 2402MHz – 2480MHz
- Maximum Power: 10mw
- Weight: 95g.
- Maximum cooperation temperature: 45°c
- Hardware Version: revD (Earbuda) / revE1 (Charge Case)
- Software Version: v4.5 (Earbuds) / v1.0.0.6 (Charge Case)
Contains a Li-ion battery. The battery must be recycled or disposed of the property.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions
- this device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISED Compliance Statement
This device contains licence-exempt transmitter(s)/receivers) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
ISED SAR Compliance Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying F exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.
Skullcandy, Sand other marks are registered trademarks of Skullbandy, Ino. All right reserved.
MODEL: S2BPW
FCC ID: Y22-82BPW
IC: 10486A-82BPW
WARRANTY
1-Year Global Limited Warranty
United States of America and Canada Product Purchases Only Skulcandy products are backed by a 1-year limited warranty. I it doesn’t work the way we promised, we’ll make it right. For Guarantee Claims, Questions, and Terms & Conditions visit www.skulcandy.com/warranty or call us at 1-888-MYSKULL.
SIMPLIFIED EU
DECLARATION OF CONFORMITY
Hereby. Skullcandy Internation GmbH declares that the radio equipment type [Model: S2BPW is in compliance with Directive 2014/53/EU. The full text of the EU declaration of Conformity is available at the following internet address: Skullcandy.eu/product-documents
Contacts
Americas
- Skullcandy, Inc.
- 6301 N Landmark Dr.
- Park City, UT 84098 U.S.A.
- Skullcandy.com
Europe
- Skullcandy Europe BV
- Postbue 425
- 5500AK Veldhoven Nederland
- Skullcandy.eu
Canada
- Skullcandy Canada ULC 329 Railway St. Unit 205
- Vancouver, BC. VA 1A4 Canada
- Skullcandy.ca
Méxioo
- Skulcandy Mexico 8 de RL de CV Aristoteles 218
- Polanco IV Seccion, Miguel Hidalgo 11550, México City, Méxioo
- Skullcandy.mx
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>