WyreStorm NHD-0401-MV HDBaseT Switching Extender with USB2.0 and Relay Triggering User Guide
- June 10, 2024
- WyreStorm
Table of Contents
Quickstart Guide
4-Input 4K60 Multiview Processor for NetworkHD™
NHD-0401-MV
Wyre Storm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the installation process.
****IMPORTANT! Installation Requirements
- Read through the Wiring and Connections section for important wiring guidelines before creating or choosing premade cables.
- Visit the product pages to download the latest firmware, document version, additional documentation, and configuration tools.
In the Box
1x NHD-0401-MV Switcher
1x 12V 2A Power Supply (US/UK/EU/AU)
1x IR Remote
1x IR Receiver Cable
2x Wall Mounting Brackets
2x Rack Mounting Brackets
1x Quickstart Guide (This Document)
Wiring Diagram – NetworkHD Solution
Wiring Diagram – Standalone
Solution
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and
terminated prior to making connections to the switcher. Read through this
section in its entirety before running or terminating any wires to ensure
proper operation and to avoid damaging the equipment.
IMPORTANT! Wiring Guidelines
- The use of patch panels, wall plates, cable transmitters, kinks in cables, and electrical or environmental interference will have an adverse effect on signal transmission which may limit performance. Steps should be taken to minimize or remove these factors completely during installation for best results.
- WyreStorm recommends using pre-terminated VGA, HDMI, DP and USB cables due to the complexity of these connector types. Using preterminated cables will ensure that these connections are accurate and will not interfere with the performance of the product.
Communication and Connections
RS-232 Wiring
The NHD-0401-MV uses a 3-pin RS-232 with no hardware flow control. Most
control systems and computers are DTE where pin 2 is RX, this can vary from
device to device. Refer to the documentation for the connected device for pin
functionally to ensure that the correct connections can be made.
Audio Connections
The audio connection uses a 3.5mm (1/8in) TRS stereo jack. Setup and
Configuration
The NHD-0401-MV is designed to work natively with the NHD-CTL-PRO for
management, setup and configurations. However, the NHD-0401-MV can also be
used as a standalone multiview switcher.
Setup via the NHD-CTL-PRO
The NHD-CTL-PRO will automatically locate and display the NHD-0401-MV in its
web interface. Ensure that the NHD-CTL-PRO and NHD-0401-MV are in the same IP
address range.
Setup as a Standalone Switcher
The NHD-0401-MV contains a web interface that can be accessed directly by
entering it’s IP address into a web browser. The switcher can also be
controlled via API commands from a 3 rd -party control system. Communication
settings are listed.
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
- Verify that power is being supplied to the switcher
- Verify that all HDMI connections are not loose and are functioning properly.
- Verify that the output resolution of the source and display is supported by this switcher.
- Configure EDID Settings to a lower resolution.
- If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
Warranty Information
WyreStorm Technologies ProAV Corporation warrants that its products to be free
from defects in material and workmanship under normal use for a period of five
(5) years from the date of purchase. Refer to the Product Warranty page on
wyrestorm.com for more details on our limited product
warranty.
HDMI cable Performance Guide
| WyreStorm Connector | 3rd Party Device | |
|---|---|---|
| Pin 1 | TX (Transmit) | —> To —> |
| Pin 2 | RX (Receive) | —> To —> |
| Pin 3 | G (Ground) | —> To —> |
RS-232 and IP Settings
| Baud Rate: | 115200 |
|---|---|
| Data Bits: | 8bits |
| Parity: | None |
| Stop Bits: | 1bit |
| Flow Control: | None |
| Default IP Address: | DHCP |
| Default IP Port: | 23 |
No or Intermittent 3 rd party Device Control
Verify that the IR, LAN or RS-232 cables are properly terminated.
NHD-CTL-PRO Won’t Find Switcher
- Verify that both the switcher and controller are in the same IP address range
- Ensure firmware is update to date
Copyright © 2022 WyreStorm Technologies |
wyrestorm.com
NHD-0401-MV Quickstart Guide | 221021
INT: +44 (0) 1793 230 343 | US: 844.280.WYRE (9973)
support@wyrestorm.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>