ALPHA FAN PRIMA-5B LED Ceiling Fan Instruction Manual

June 10, 2024
ALPHA FAN

ALPHA FAN PRIMA-5B LED Ceiling Fan

SAFETY PRECAUTION

Warning
Installation and maintenance work shall only be performed by qualified persons, familiar with local code and regulations, and experienced with this type of appliance. All field wiring must be installed in accordance with the national wiring regulation. Ensure that the rated voltage of the unit corresponds to that of the nameplate before commencing wiring work according to the wiring diagram. The appliance must be permanently connected to the electricity supply through a double pole switch having a contact separation of at least 3mm in all poles

The unit must be GROUNDED to prevent possible hazards due to insulation failure.
The earth wire is approximately 60mm longer than the safety wire. This is to ensure at the event whereby the suspension system fails, the (L) and (N) wire will break leaving the fan remain earthed to prevent electrocution.

Tighten the blade firmly using a screwdriver.
Blades that are detached from the unit during operation will cause serious injuries and property damage.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliances. Confirm that the power supply has been switched OFF before installing or servicing the unit. Ensure that the blade is fully static before doing any maintenance work.

STOP using the ceiling fan when any abnormality or failure occurs.
If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent or suitably qualified persons.

CAUTION

Please take note of the following important points when installing.
The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a sufficient strength to withstand 4 times the weight of the ceiling fan.

The mounting of the suspension system shall be performed by the manufacturer, its service agent or suitably qualified persons. The fan is to be installed so that the blades are more than 2.5m above the floor.

Safety cord should not be longer than the earthing conductor.
Should failure of the suspension system occur, the supporting of the fan must not rely on the earthing conductor. The earthing terminal in the fan assembly should be such that should any part of the suspension system fall off, the body of the fan assembly shall effectively earthed.

Ensure that the unit’s panel is closed after service or installation.
Unsecured panels will cause the unit to operate noisily.

Sharp edges and coil surfaces are potential locations which may cause injury hazards. Avoid from being in contact with these places.

Before turning off the power supply set the remote controller’s ON/OFF switch to the “OFF” position.

  • If this is not done, the unit’s fans will start turning automatically when power resumes, posing a hazard to service personnel or the user.
  • Do not operate any heating apparatus too close to the ceiling fan unit or use in a room where mineral oil, oil vapor or oil steam exists, this may cause the plastic part to melt or deform as a result of excessive heat or chemical reaction.
  • Avoid the ceiling fan unit from exposing to direct sunlight, this may cause degradation of plastic material as a result of excessive heat and UV radiation.
  • Ensure the colour of the wires of the outdoor unit and the terminal markings are the same to the indoors respectively.
  • Do not use joined and twisted wires for incoming power supply.
  • Do not place any object in the path of the blades. Avoid raising objects or your arms near the ceiling fan.
  • The fan suspension system and blade screw tightening shall be examined yearly.
  • Replacement of parts of the safety suspension system device shall be performed by the manufacturer, its service agent or suitably qualified persons.
  • The torque value for screws/bolts for securing the primary suspension system for the motor is 2Nm.

Parts & Accessories

ALPHA-FAN-PRIMA-5B-LED-Ceiling-Fan-fig- \(1\)

Installation Instruction

Step 1

  • Route all the wires from the Motor through the Motor Bracket.
  • Route all the wires through the Downrod.
  • Fix the Motor Bracket and Downrod to the Motor Assembly with Bolt, Washer, Nut and tighten them firmly then insert the Clevis Pin.

IMPORTANT:
CLEVIS PIN MUST BE INSERTED TO PREVENT NUT FROM LOOSENING.

Step 2

  • Assemble the Canopy and Coupling Cover through the Downrod.
  • Fix the Rubber Pulley Assembly to the Downrod with Bolt, Washer, Nut and tighten them firmly, then insert the Clevis Pin.ALPHA-FAN-PRIMA-5B-LED-Ceiling-Fan-fig- \(3\)

Step 3

  • Remove the Bolt, Clevis Pin, Nut, Washer and Rubber Pulley from the Downrod. Place the Rubber Pulley onto the ceiling hook and fix back the Bolt, Clevis Pin, Nut and Washer.
  • Remove the Safety Wire screw and spring washer from the Downrod.ALPHA-FAN-PRIMA-5B-LED-Ceiling-Fan-fig- \(4\)

Step 4
Tie the Safety Wire across the hook as shown.ALPHA-FAN-PRIMA-5B-LED-
Ceiling-Fan-fig- \(5\)

Step 5

  • Connect the Connectors from Fan and Receiver.
  • Connect the wires from the receiver to House’s Supply Wire.
  • Connect Earth Wire to House Supply Earth Terminal.

Step 6
Install the Blades on the Motor with the Screw.

Step 7
Install Lamp Shade by twisting it in.

ALPHA-FAN-PRIMA-5B-LED-Ceiling-Fan-fig- \(8\)

Step 8
Below shows a complete installation diagram.

ALPHA-FAN-PRIMA-5B-LED-Ceiling-Fan-fig- \(9\)

TRANSMITTER LEARNING PROCESS

IMPORTANT:
DO NOT CONNECT THIS REMOTE CONTROL CEILING FAN TO THE DIMMER SWITCH OR REGULATOR.

The receiver & transmitter is pre-programmed in the factory. If you wish to control 2 or more fans using 1 transmitter, the below steps are required.

DO NOT PRESS ANY OTHER BUTTON DURING THIS PROCESS

Step 1

  • Insert the 2 pcs of batteries (provided) into the transmitter.
  • Turn on the power supply (wall switch) to the fan.
  • Within 30 sec, press and hold the “LEARN” button for 3 sec. Once the receiver has detected the frequency, the transmitter will “Beep Beep” twice. The programming process is completed and fan is ready to use. If the fan is not responding to the transmitter, repeat Step 1b.

TRANSMITTER FUNCTION

IMPORTANT:
DO NOT CONNECT THIS REMOTE CONTROL CEILING FAN TO DIMMER SWITCH OR REGULATOR.

ALPHA-FAN-PRIMA-5B-LED-Ceiling-Fan-fig- \(11\)

The transmitter & receiver is incorporated with last memory function. This function stores your last setting in memory and the next time you turn on the fan, fan will operate as the last setting.

The function of Forward & Reverse

Fan must be turned on and rotating.

Press and hold the Forward/Reverse button for 3-sec fan will slow down and then change direction (approx. 15 sec). When the fan is slowing down to change direction, the Fan Speed function is disabled until the direction has been changed.

ALPHA-FAN-PRIMA-5B-LED-Ceiling-Fan-fig- \(12\)

Forward
Fan rotates anti-clockwise blowing the air downwards creating the wind chill effect. Suitable for hot weather conditions.

Reverse
Fan rotates clockwise drawing the air towards the ceiling and circulating the warm air downwards. This function works best at low speed. Suitable for air- conditioned conditions.

POWER SUPPLY CONNECTION

CIRCUIT DIAGRAM

IMPORTANT:
DO NOT CONNECT THIS REMOTE CONTROL CEILING FAN TO THE DIMMER SWITCH OR REGULATOR.

ALPHA-FAN-PRIMA-5B-LED-Ceiling-Fan-fig- \(14\)

MAINTENANCE

Due to the fan’s natural movement, connections may get loose after a period of usage. To ensure proper and safe usage, inspect the suspension system and tighten all connections every 6 months.

Cleaning

Cleaning your fan periodically will prolong its new appearance. Basic cleaning procedures are as follows :

  1. Use only lukewarm water. Do not use detergent, corrosive or acidic solution.
  2. Damp the cloth lightly. Use only soft or lint-free cloth to clean the fan. Rough fabric will scratch the fan surface.
  3. To cover small scratches, apply a light coat of shoe polish over it.
  4. There is no need to oil the fan.

TECHNICAL SPECIFICATIONS

Model PRIMA-5B/56 LED PRIMA-5B/40 LED
No. of Blades 5 5
Fan Width 1420mm (56”) 1015mm (40”)
Motor RPM 70 – 210 80- 240
Voltage 220-240V~ 50Hz 220-240V~ 50Hz
Motor Wattage 4W – 45W 4W – 40W
LED Wattage 22W 22W
Nett Weight 6.0kg 5.7kg

ALPHA-FAN-PRIMA-5B-LED-Ceiling-Fan-fig- \(15\)

CUSTOMER SERVICE CENTRE

If you need any technical assistance or a faulty report, please contact our customer service center at:

Alpha Home Appliances Sdn. Bhd. (390258-H)

  • Head Office: 6, Jalan Sungai Kayu Ara 32/37, Berjaya Park, Section 32, 40460 Shah Alam, Selangor.
  • Tel: 03-5740 6666
  • Fax: 03-5740 8220
  • Website: www.alphamalaysia.com.
  • Email: info@alphamalaysia.com.
  • Johor Bahru: 71, Jalan Molek 3/10, Taman Molek, 81100 Johor Bahru.
  • Tel: 07-353 4833 / 4933
  • Fax: 07-355 4233
  • Melaka: 19, 19-1 & 19-2, Jalan KSB 11, Taman Kota Syahbandar, 75200 Melaka.
  • Tel: 06-292 6292 / 6293
  • Fax: 06-292 6296
  • Ipoh: 11, Lalua n Tasek Timur 5, Taman Tasek Indra, 31400 Ipoh, Perak.
  • Tel: 05-545 2282 / 547 2282
  • Fax: 05-547 6282
  • Penang: 28, Jalan Icon City, Icon City, 14000 Bukit Mentajam, Penang.
  • Tel: 04-506 2366 / 2066 / 2566
  • Fax: 04-506 2966
  • Pahang: A131, TK1, Jalan Wang Ah Jang, Taman Liza, 25100 Kuantan, Pahang.
  • Tel: 09-516 5226
  • Fax: 09-513 9226

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals