UTV Stereo Pro Series 6.5 Inch Performance Speakers Owner’s Manual
- June 10, 2024
- UTV Stereo
Table of Contents
- GENERAL FEATURES
- SPEAKER BREAKDOWN
- SPECIFICATIONS
- INCLUDED PARTS LIST
- THANK YOU FOR CHOOSING UTV STEREO PRODUCTS
- INSTALLATION
- Option #1: OEM DASH INSTALLATION
- Option #2: UNIVERSAL INSTALLATION
- UNIVERSAL INSTALLATION
- Option #3: OEM REAR INSTALLATION
- WARRANTY **
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Owner’s Manual
GENERAL FEATURES
Designed to Fit OEM & Aftermarket Enclosures
100% UV Protected
Removable RGB LED Grille
Dynamic, Crisp Highs & Balanced Mids
Neodymium Magnet
IP65 Rated – Dustproof & Splash Resistant Built-In Crossover
PRO-SERIES 6.5″ Performance Speakers Owner’s Manual
SPEAKER BREAKDOWN
- REMOVABLE LED RGB GRILLE
- LED RING CHAMBER
- 35MM FOUR LAYER VOICE COIL (WOOFER)
- 75MM NEODYMIUM MAGNET (WOOFER)
- PREMIUM TETOLON DOME (TWEETER)
- 22MM VOICE COIL (TWEETER)
- 24MM NEODYMIUM MAGNET (TWEETER)
- BUILT-IN CROSSOVER
SPECIFICATIONS
Frequency Response: | 45Hz-20KHz |
---|---|
Nominal Impedance: | 4 Ohm |
Sensitivity: | 90dB @ 1W/1m |
Continuous Power | 80W |
Peak Power | 500W |
INCLUDED PARTS LIST
THANK YOU FOR CHOOSING UTV STEREO PRODUCTS
Thank you for choosing UTV Stereo products. Your purchase of this UTV Stereo
product for use in your UTV indicates your desire for reliablity and
performance audio that only comes from UTV Stereo.
UTV Stereo is your premier audio manufacturer. We offer the highest quality
products designed for your SXS. Stay one step ahead when you purchase UTV
Stereo products.
To take full advantage of the UTV Stereo Pro-Series 6.5″ Speakers, please read
and follow the instructions in this manual.
Designed for high performance audio systems, these speakers are built rugged
to withstand the elements with an IP65 dustproof and water-resistant rating.
These Pro-Series 6.5″ Performance Speakers have been designed specifically for
use in SxS’s!
INSTALLATION
Professional installation by an authorized UTV STEREO dealer is highly
recommended! Otherwise, the performance of your new gear may not be
satisfactory. In the event that you decide to do your own installation, please
read and follow this manual very carefully. Failure to do so may compromise
the integrity of this product or your vehicle, and possibly void this
product’s warranty.
THERE ARE THREE OPTIONS FOR INSTALLATION
Option #1 – OEM DASH INSTALLATION • We have designed this speaker with a
removable RGB LED Grille to fit into the OEM dash speaker housing on RZR® Pro
Series Models. OEM Housing mount does not allow for use of included Pro Series
RG8 LEO Grille.
Option #2 – UNIVERSAL INSTALLATION • Follow these instructions (beginning
on (Page 08) to install Pro Series 6.5″ speaker using the RGB LED Speaker
Grille on universal 6.5″ speaker enclosures.
Option #3 – OEM REAR INSTALLATION: Combine techniques of Option #1 and #2
to mount into Rear OEM Enclosure.
Option #1: OEM DASH INSTALLATION
Option #1• OEM INSTALLATION
Designed to fit RZR® Pro Series Models OEM Instructions begin on Page 04.
REQUIRED PARTS FOR OEM DASH
INSTALL
STEP 1: Line up holes and apply Small Rubber Gasket (adhesive side down) to
the back of the Pro-Series Speaker.
Failure to use the included OEM
harness WILL result in poor sound quality.
STEP 2: Attach the Female ends of the Included OEM Harness to the (Male)
Terminals on the back of the Pro-Series Speaker, respectively.
STEP 3: Attach the Male ends of the OEM harness into the Female ends
(Female ends come standard in your OEM speaker housing.)
STEP 4: Mount the speaker to your OEM housing as shown in Figure A on
Page 05 using the included M4-.7x12mm Panhead Machine Screws.
OEM DASH INSTALLATION COMPLETE
Option #2: UNIVERSAL INSTALLATION
Option #2: UNIVERSAL INSTALLATION
Designed to fit Standard 6.5″ Speaker Enclosures UNIVERSAL Instructions begin
on Page 09.
REQUIRED PARTS FOR UNIVERSAL INSTALL
UNIVERSAL INSTALLATION
STEP 1: Attach the RGB LED
Grille to the front of the speaker using 4 of the included Phillips Head
3x1Omm countersunk screws per each Speaker & Grille. Make sure the notch in
the speaker lines up with the notch in the grille so that RGB wires can pass
through without being pinched.
STEP 2: Run the LED RGB Grille
Harness wires through the notch in the speaker.
STEP 3: Set the Large Gasket
(Adhesive side down) on top of the RGB LED Grille Harness wires, making sure
the notch in the gasket lines up with the notch in the speaker.
STEP 4: Crimp the included
(RED) Female Terminal Connectors onto the speaker wires coming from the
amplifier, and insert onto terminals of the speaker. If desired you may now
add an optional UTV Stereo BT RGB Controller. For complete ROB functionality.
Simply plug the UTV Stereo BT RGB Controller into existing Pro-Series RGB LED
Harness following instructions included with the UTV Stereo 131 RBG
Controller.
Option #2: UNIVERSAL INSTALLATION (RGB ORIENTATION)
Option #3: OEM REAR INSTALLATION
Option #3: OEM REAR INSTALLATION
Designed to fit Rear OEM RZR® Pro Series Models 6.5″ Speaker Enclosures
If RGB LED connection is desired
additional parts and labor required.
REQUIRED PARTS FOR UNIVERSAL INSTALL
If RGB LED connection is desired,
additional parts and Labor required.
STEP 1: Attach the RGB LED
Grille to the front of the speaker using 4 of the included Phillips Head
3x1Omm countersunk screws per each Speaker & Grille. Make sure the notch in
the speaker lines up with the notch in the grille so that RGB wires can pass
through without being pinched.
STEP 2: Run the LED RGB Grille
Harness wires through the notch in the speaker.
STEP 3: Set the Large Gasket (Adhesive side down) on top of the RGB LED
Grille Harness wires making sure the notch in the gasket lines up with the
notch in the speaker.
Failure to use
the included OEM harness WILL result in poor sound quality.
STEP 4: Attach the Female ends of the included OEM Harness to the (Male)
Terminals on the back of the Pro-Series Speaker, respectively.
STEP 5: Attach the Male ends of
the OEM harness into the Female ends (Female ends come standard in your OEM
speaker housing.)
STEP 6: Mount the speaker to your OEM housing as shown in Figure C on Page 12
using the included M4-.7x18mm Panhead Machine Screws.
OEM REAR INSTALLATION COMPLETE
PRO-SERIES 6.5″ Performance Speakers Owner’s Manual
WARRANTY **
**
Should your product require service, please consult with the dealer from which
it was purchased or contact a local UTV STEREO dealer directly. Units received
without an accompanying return authorization number will not be processed.
Please contact your UTV Stereo dealer or contact UTV Stereo directly to obtain
a return authorization number. Additionally, you must include a copy of your
purchase receipt from an authorized UTV Stereo dealer for consideration of an
in-warranty service. Units received without a receipt will be held for 30
days. Allowing us time to contact you and obtain a copy of the receipt. After
30 days, all units will be returned.
DO NOT SUBMERGE THIS PRODUCT. THIS WILL VOID YOUR WARRANTY.
UTV STEREO and the UTV STEREO Logo are registered trademarks.
All other brand names are trademarks or registered trademarks of their
respective owners.
These trademark holders are not affiliated with UTV Stereo All rights
reserved. Designed in USA.
Copyright© 2023 UTV STEREO
Tel. 480-616-2299
Address: 7561 East Baseline Road Mesa, AZ 85209
Designed in USA utvstereo.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>