KODAK BTSP110 Wireless LED Speaker User Manual
- June 10, 2024
- Kodak
Table of Contents
KODAK BTSP110 Wireless LED Speaker
IMPORTANT SAFETY INSTRUCTIONS
- Read these instructions carefully.
- Keep these instructions in a safe place and follow all instructions.
- Do not use this product near water.
- Cleaning: Do not use liquid cleaners or aerosol cleaners. Clean only with a dry damp cloth.
- Do not place near any heat sources such as radiators, heat registers, stoves, or other apparatuses (including amplifiers) that produce heat.
- Only use attachments/accessories specified by the manufacturer.
- Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as objects have fallen into the product, does not operate normally, or has been dropped.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
IC Warning
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
ISEDC Radiation Exposure Statement:
This equipment complies with ISEDC RF radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
This device complies with Canadian ICES-003 and RSS-247
Thank you for your purchase.
LOCATION OF CONTROLS
| 1. ON / OFF Switch | 6. MicroSD Input |
|---|---|
| 2. Micro USB Charging Port | 7. Next Button / Volume Increase Button |
| 3. Aux-in Port | 8. Play / Pause Button |
| 4. Charge Indicator Light | 9. Previous Button / Volume decrease Button |
| 5. USB Input | 10. Mode Button |
CHARGING THE SPEAKER
Using the Charging Cable, plug the Micro USB Tip into the Micro USB Charging Port and plug the other end (USB Tip) into a USB port on your computer or USB wall charger (not included). The LED Indicator Light will illuminate red while charging and turn off when completed. A full charge will take approximately 3-4 hours.
Product and Battery Disposal
This product contains a built-in lithium battery and should not be disposed of
in normal household waste. The battery in this device is not intended to be
removed by the individual or end user. For disposal and recycling, please
contact your local waste management authorities. The recycling and processing
of electronic waste will make a significant contribution towards helping
protect the environment.
Warning : To reduce the risk of fire and burns, do not disassemble, crush, puncture, short external contacts or dispose of in fire or water.
POWER ON/OFF
To turn on/off the speaker, slide the toggle switch to the ON or OFF
position.
BLUETOOTH MODE
Pairing a Bluetooth Enabled Device for the First Time to your Bluetooth
Speaker
NOTE: Refer to the user manual for your Bluetooth enabled device for
instructions on pairing and connecting Bluetooth devices.
-
Keep the unit and your Bluetooth enabled device within 1 metre at all times during the pairing process.
-
Turn on the speaker and press the Mode Button and toggle to the Bluetooth mode.
-
Turn on the Bluetooth function on your Bluetooth enabled device and search for Bluetooth devices. When the search is complete, select “BTSPK110” from the Bluetooth device list.
NOTE:- If pairing was unsuccessful, turn off the speaker first and repeat the steps above to re-pair again.
- After successful pairing, paired devices will remember each other. Unless pairing information is deleted, re-pairing is not required after the first time.
- If you want to pair the unit with other Bluetooth enabled devices, please disconnect/remove the existing device and pair with the new device according to the steps above.
-
To increase or decrease the volume on the speaker, press and hold the Volume Increase or Volume Decrease Button.
-
To skip songs forward or backward, press the Previous or Next Button.
-
To pause and resume playback, press the Play/Pause button.
FM MODE
Press the Mode Button to cycle through to the FM Mode. Press and hold the
Play/Pause Button to start the auto search function. Once the auto search
feature is completed, all stations with signal will be saved into memory. Use
the Previous or Next Buttons to search through the saved stations.
Tips for Best Reception : If the FM reception is weak, change the position or location of the unit or try placing the unit near a window until you get the best reception.
AUX-IN (AUDIO INPUT) MODE
Using a 3.5mm aux-in cable (not included) plug one end into a smartphone,
tablet, MP3 player or other audio source and the other into the Aux-in Port.
Press the Mode Button to cycle through to the Aux-in Mode.
USB MODE
This unit allows you to play music from a USB thumb drive with MP3
formatted files. Insert the USB thumb drive. Press the Mode Button to cycle
through to the USB Mode.
MICRO SD MODE
This unit allows you to play music from a MicroSD memory card with MP3 formatted files. Insert the MicroSD card. Press the Mode Button to cycle through to the MicroSD Mode.
NOTE: To insert the MicroSD card, use your fingernail to help push it in
all the way until it clicks in. To remove the MicroSD card, push it in all the
way and it will click out. The microSD memory card can be left in the speaker
or taken out. It will not affect the function of the speaker as you cycle
through the different modes.
Need help? Please call us.
If you encounter any difficulties with this product, please call or email us
and our representatives will be ready to help you.
Toll free: 1-800-593-6669 (Monday to
Friday: 9am – 5pm EST)
Email: support@borne-lifestyle.com
Thank you for your purchase. We want you to start enjoying your product.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>