HUANANZHI X99-QD4 Motherboard User Manual

HUANANZHI X99-QD4 Motherboard

Product Information

The SZ HUANAN SANXIAN TECHNOLOGY CO., LTD. motherboard is designed with advanced features including:

• Supports Intel Xeon and LGA 2011 processors
• DDR3 memory with ECC support
• Multiple SATA ports, USB ports, and PCIe slots
• Realtek LAN and audio drivers
• BIOS with CMOS setup and SRAM

Product Usage Instructions

Before assembling the computer, please follow these safety precautions:

• Avoid electrostatic discharge by discharging your body static by touching other metal objects before taking the motherboard out of the box.
• Hold the border of the motherboard when taking it out and do not touch the sensitive parts of the motherboard.
• Confirm that the motherboard is properly packaged upon purchase. If there is any damage to the packaging or lack of accessories, contact the manufacturer as soon as possible.

To install the motherboard and set up the computer, follow these steps:

1. Firmly connect all parts to prevent failure of recognizing components or starting the computer.
2. Install drivers for the motherboard including Intel chipset, Realtek LAN, and Realtek audio drivers.
3. Configure BIOS settings through CMOS setup and SRAM to optimize system performance. The BIOS includes main, advanced, chipset, boot, security, save, and exit settings.

For more information on installation and settings, refer to the included motherboard diagram and rear I/O panel guide.

SAFETY PRECAUTIONS

• Products could probably be damaged due to electrostatic discharge(ESD). Please follow the steps below for a successful computer assembly.
• Make sure all parts are firmly connected; otherwise, it might lead to the failure of recognizing components or starting the computer.
• In order to prevent products from being damaged by ESD, please make sure to discharge your body static by touching other metal objects before taking the motherboard out of the box.
• Hold the border of the motherboard when taking it out. Do not touch the sensitive parts of the motherboard.
• Please put the motherboard in an anti-static container or on an anti-static pad if not needed.
• Before turning on the computer, make sure all parts inside the case are firmly connected without any loose screws or metal components.
• Do not start the computer before installation finished, otherwise, it might result in permanent damage to the computer parts or even injury to the user.
• If you need any assistance in the process of installation, please contact our after-sales customer service or reach us on HUANANZHI official E-mail:business@huananzhi.com for professional technical support.
• Prior to installation or disassembly, please switch off the power and pull the power cable from the socket.
• Keep the motherboard away from moisture.
• Keep the user manual for future reference.
• Before plugging the power supply, please make sure the socket provides the corresponding voltage.
• In any of the following situations, please keep the motherboard and power cable in a safe place. Do not put anything on the power cable.
• In the event of any of the following conditions, have the board checked by a service technician:
  • Liquid penetrated into the computer.
  • The motherboard is exposed to moisture.

The motherboard does not work even if you follow the instructions on user manual.
Motherboard fell off to the ground and got damaged. Motherboard has clear signs of damage.

PACKING

Please confirm that the motherboard is properly packaged upon purchase of the product. If there is any damage to the packaging or lack of accessories, contact us as soon as
possible.

1. HUANANZHI X99-QD4 Motherboard
2. SATA data cable
3. User manual
4. Warranty card

BRIEF INTRODUCTION

Features

• CPU:
  • Intel ® LGA2011-3 Processor Intel ® Xeon ™
  • Intel ® LGA2011-35/6 Generation Intel ® Core ™
• RAM:
  • 4*DIMM supports up to 128GB DDR4 2400/2133/1866 MHZ Non-ECC.ECC memory
  • Quad-Channel Memory Architecture
  • Actual memory data rate depends on CPU type and DRAM module
• I/O effects:
  • 6x SATA3.0 (maximum transfer speed up to 6GB/s)
  • 4x USB2.0 interface
  • 2x USB3.0 ports
  • 1x PS/2 Mouse and Keyboard port
  • 1x RJ45 Network card interface
• Audio:
  • Realtek Audio Transcoder
  • Realtek 5.1 Channel High Fidelity Audio
  • Audio output: Front Out/Front Speaker Out
  • Audio input : Microphone input, Audio input
• Ethernet: 1x Realtek PCle Gigabit LAN
• Expansion slot:
  • 1x PCIe 3.0 x16
  • 1x PCIe 3.0×4
  • 1x PCIe 2.0 x1
  • 2x M.2 NVME PCIe 3.0X4 (key M)2224/2260/2280

MOTHER-BOARD IMAGE

Rear I/O Panel

Installation And Settings

NOTICE please check the motherboard where all pins marked with number “1” or white bold line are position“1”

M.2 Interface Installation

1. Remove the screw from the screw base.
2. Remove the screw base.
3. Tighten the screw base screwed into the length M.2 module to the M.2 interface distance hole.
4. Insert your M.2 module into the M.2 interface at a 30-degree angle.
5. Place the screw on the trailing edge notch of your M.2 module and tighten to the screw base.

Memory Installation

1. Pull the clips on both ends of the memory slot outward, and the memory strip corresponds to the protruding position of the slot to determine the direction of installation.
2. Align the memory module into the slot and press.
3. Let the snaps on both ends of the slot automatically bounce.

Graphics Card Installation

1. Use a screwdriver to remove the bezel and screws on the main unit.
2. Need to pick up the card slot of the card slot when installing the graphics card.
3. Insert the graphics card into the card slot of the graphics card.
4. After the installation is in place, the chuck will automatically return to its position.
5. Secure the graphics card to the chassis with screws.
6. Install the power cord.

Drivers installation

1. Drivers listing:

2. Intel Chip Information Installation
   Run“ Control Panel – System – Hardware – Device Manager” Click the right mouse button to change the driver’s hardware device and proceed with the installation below:
   Option: Propertyl – Update driverl – Not connect to Internet – Manually installation
   Find the corresponding directory Select “Next step”

3. Audio driver installation
   Before this installation, please check the model of the audio chip on the motherboard first(you may refer to this manual), Select the proper driver accordingly for installation.

4. Audio driver installation (take HD Audio series for example)
   Run “driver installer”: /X99-QD4 Realtek Audio/setup.exe Click on “next”to continue,and then”finished” The system will automatically restart itself to finish the installation

5. Uninstallation of audio driver(take HD Audio series for example)
   setting int o Windows desk top, choose “setting”/ “control”,and then “add/remove programs”. Later, choose “Realtek High Definition Audio Driver” in the menu and click on ” add/remove”so thatthe driver will be aut omatically removed.

6. Driver installation of external video card
   Run “driver installer”, take Setup.exe, Click on “next”- “yes” -“next” -“next”and”finished”h
   The system will automatically search for devices to complete the installation

7. Driver installation of network
   Run “driver installer”: X99-QD4 LAN DRIVER /Install_Win7_7126_0624019/Install_Win10_10035_06242019/setup.exe click on “next”- “installation”- “finished”and restart the computer， and restart the computer，The system will automatically search for devices to complete the installation.

BIOS Settings

In order to enable the computer to work well or execute specific functions, CMOS SETUP normally stores all kinds of data in CMOS SRAM of the motherboard. When the computer is shut down, motherboard’s battery will supply power to CMOS SRAM. When the computer is turned on and starts POST(Power On Self Test), press “Delete/Del” key to enter into AMI BIOS CMOS SETUP main page. Motherboard warm boot key is“ F7”

Menu: please pay attention to every option in the settings menu. When there is a triangle shaped symbol on the left side of menu, it means that you choose this sub-menu,so a pop-up sub-menu will be available.

Main Menu Function

• Main

• System Overview
  Date/Time settings, HDD specs/Monitor type settings.

• Advanced
  Advanced Settings
  BIOS special function settings, such as virus alert, booting disk priority etc.

• Chipest
  Advanced Chipest Settings

• Boot
  Boot Settings

• Security
  Security Settings

• Save
  Save Setting

• Exit
  Exit Options
  Exit settings include loading of optimized defaults value/ loading of fail- safe defaults / discarding changes/ exiting without saving.Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving.

WWW.HUANANZHI.COM

References

• 华南金牌官网

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>