tracer 4.0D FHD Mensa Dash Camera Instruction Manual
- June 10, 2024
- Tracer
Table of Contents
tracer 4.0D FHD Mensa Dash Camera
OVERVIEWS
Safety instructions
-
Keep the unit away from heat sources, direct sunlight, humidity, water and any other liquids.
-
Do not operate the unit if it has been exposed to water, moisture or any other liquids to prevent against electric shock, explosion and/or injury to yourself and damage to the unit.
Do not use the unit if it has been dropped or damaged in any way. -
Repairs to electrical equipment should only be performed by a qualified electrician.
-
Improper repairs may place the user at serious risk.
-
Do not use the unit with wet hands.
-
Do not use this unit for anything other than its intended use.
-
Keep the unit out of reach of children. This appliance is not a toy.
-
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat place, such as sunshine, fire.
1| DC Power/ USB Interface. Connect with car charger or DC(5V-12V)
power to charging
---|---
2| AV-IN rear camera slot. Connect with external rear camera
3| TF Card Slot. Insert Micro SD Card or TF Card,4-32GB Class10
high speed
4| Reset Hole
5| Mode/Menu Key: while working short press to enter the Menu
settings. Long press to switch the modes (recording, photo, playback)
6| UP Key. In the menu, use UP key to scan and choose the menu
options. In the playback mode, use Up key to scan and choose video files
to play
7| Power Key. Long press to turn on/off the device. Short press under
working state, open/close the screen saver
8| Down Key. Under Recording Mode, a short press on Down Key the mute
the video recording
9| OK Key. While Recording Mode, a short press on OK Key to start/
stop recording. In the menu, use OK key to confirm the settings
Installation guide
- Turn off the car engine.
- Insert the TF card into the recorder card slot. Please use high-speed TF card (Class10 or higher), the capacity 8-32GBFix the recorder to the suction cup bracket on the glass of the car.
- Insert the car charger into the car cigarette lighter.
- Using enclosed mounting elements please put the mirror dash cam on the front mirror inside the car.
- Adjust the lens position to ensure that the lens is level with the ground. Plug in the rear cam to the proper slot on the dash cam. For automatic switch to the image from the rear camera, after using reverse gear, please connect the red cable from the rear camera extension cord to the+ 12V terminal on the reverse lamp bulb. It is recommended that you use the services of a qualified workshop.
- Connect the USB port to the car charger with a charging extension cable. The wiring extension cable can be laid along the edge of the windshield of the car during wiring.
- Start the engine and check that the machine is installed correctly. When the machine is installed correctly, the system work indicator lights up; the machine starts to enter the recording state, and the recording indicator flashes. Please check if the picture on the display is normal.
Function introduction
- Motion Detection: in standby, detect object is moving front of camera, camera will record video automatically, press OK button to stop and turn off the function
- Loop recording: to select video time in 1/3/5 minutes, it will delete the first file automatically to keep recording.
- G-sensor: It is one of the most important functions of a car camera. It is a sensor that evaluates all the forces that act on the car while driving and maneuvering on the road, and as a result of road incidents. In a situation where the forces detected by the sensor are higher than those in normal use, sensor sends a signal to the camera and blocks the recorded video from being deleted. For example, in the event of a collision by another car, or a collision while parking, the G-Sensor’s response automatically saves and blocks the recording. Thanks to this function, we have irrefutable evidence of who was at fault on the road and what were the circumstances of the event, and thus may be used as possible evidence in a case for compensation or proving guilt.
- Parking mode: turn on Parking mode in menu. Than in standby mode, once camera detect any impact, it will turn on automatically, record and secure the video.
Product specification
Video resolution|
- Single front cam recording
- FHD 1920*1080p 30fps
- Dual recording front/rear cam
- HDR 1280*720p 30fps/480p
---|---
LCD screen| 4inches, 2.5D glass
Video file format| AVI
G-sensor| Supported
Loop recording| Off/1min/3min/5min
Motion detect| Supported
Parking mode| Supported
MIC| Supported
Power interface| 5V 1A
Battery| 200mAh
The symbol of a crossed-out wheeled bin placed on electrical equipment. its packing or accompanying or accompanying documents means that the product may not be thrown out together with other waste. used equipment may contain substances with toxic and carcinogenic properties ,hazardous to human health and life ,and poisoning the soil and groundwater. it is the user’s responsibility to hand over the used equipment to a designated collection point for its proper processing contact your local authorities , waste disposal services and the place where you purchased this product. the household plays in important role in contributing to the reuse and recovery of secondary raw materials , including recycling , waste equipment. At this stage, attitudes are formed that effect the preservation of the common good , which is a clean natural environment .
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>