NYXI Wizard Switch Controller User Manual

NYXI Wizard Switch Controller

Product Information

• The product has a cursor that moves within an innermost circle.
• If the cursor bounces outside the innermost circle, press B to exit and correct it again.

Product Usage Instructions

1. Turn on the product.
2. Locate the cursor on the screen.
3. Move the cursor within the innermost circle.
4. If the cursor bounces outside the innermost circle, press B to exit and correct it again.
5. Use the cursor to navigate and interact with the product as needed.
6. When finished, turn off the product.

Package contents

• Left-hand handle * 1
• Right-hand handle * 1
• Charging cable * 1
• Manual * 1
• Intermediate bridge * 1
• Round replacement rocker ring * 2

Product specifications

• Material: ABS
• Battery: built-in 500mAh lithium battery (single-sided)
• Charging: 5V 1A
• Charging time: 3 h
• Use time: 8 h
• Wireless use distance: 10m

Product schematic

Function and operation guidelines

Note: The joypads have a memory function. The set functions are always retained unless the factory settings are restored.

Charging and charging instructions

1. The LEDs flash when the joystick is turned off for charging. When the device is fully charged, the LEDs go out.
2. The corresponding channel light flashes slowly when the handheld is charging in the wireless connection, and the channel light stays on when it is fully charged.
3. The joystick can also be installed on the Switch console, through the console connected to the power adapter for charging. (When the console is not plugged into the power adapter, the console will charge the joystick when the joystick voltage is lower than 3.7V)
4. Low battery alarm When the joystick battery voltage is lower than 3.3 V, the corresponding channel light will flash, indicating the need to charge the joystick.

Connection

Wired direct connection

Wireless connection
Open the console: joystick – change the joystick/order – long-press the SYNC key, four-channel lights flashing, the joystick is automatically connected

Wake up by any button
Except L3, R3, TURBO, Profile, FL, FR buttons, all other buttons can wake up the joystick to enter the pairing state

Note:
Please do not touch the 3D joystick during the connection process.

Turbo and speed adjustment

Setting mode:
TURBO + any one of the settable function buttons (can set the buttons UP, DOWN, LEFT, RIGHT, A, B, X, Y, L, R, ZL, ZR)

Continuous mode:
Turbo+ button 1-time manual continuous, 2 times automatic continuous, 3 times off continuous. Long press TURBO for three seconds to cancel the burst function of all buttons

Turbo speed adjustment:
left hand grip turbo + – right hand grip turbo + + Adjust the burst speed: 5HZ 12HZ 20HZ default 12HZ

Turbo setting indicator
LED lights up white when the button is not set, LED turns blue after setting, blue light flashes with the burst speed when bursting

Back-button mapping and back-button macro programming (Handle must be

connected state, please cancel the continuous when setting)

Back button mapping setting method:
Left: Profile + any settable button on the left (UP, DOWN, LEFT, RIGHT, L, ZL, L3, VRL) + Profile Right: Profile + any settable button on the right (A, B, X, Y, R, ZR, R3, VRR) + Profile

Back-button macro programming

Setting method:
Left: Profile + any of the left settable buttons (UP, DOWN, LEFT, RIGHT, L, ZL, L3, VRL) + Profile Right: Profile + any of the settable buttons on the right (A, B, X, Y, R, ZR, R3, VRR) + Profile

Note:
FL FR can record up to 21 button values, and the output will follow the time interval of the entry.

Back button setting indicator
The first time you press profile setting LED from white to blue and flashing, after the setting is complete press profile indicator blue is always on.

Back button clear
When connected to the host, hold the left and right handle Profile buttons for 3 seconds, the original functions set on the FL and FR buttons will be cleared, and the LED will turn to a long white light.

Motor vibration adjustment

Adjustment method:
Connected state (left or right) turbo + (corresponding) rocker up, down (up to enhance; down to weaken), adjust successfully with 2s vibration prompt.

Vibration level:
100% – 70% – 30% – 0%, default 70%

ABXY light adjustment
Connected state turbo + right stick double click to turn off the light effect. TURBO + right stick long press to adjust the ABXY brightness.

Factory setting “lock mode”
Setting method: When the handle is in sleep mode, press and hold the “SL”and “SYNC” buttons for 5 seconds, the channel indicator LED1 will light up and flash slowly 3 times. Unlocked mode: charge the joystick with a USB cable mounted on the Switch console rail.

Rocker ring replacement

Location schematic

1. Rocker ring pins
2. Handle alignment point
3. Rocker ring alignment line
4. Counterclockwise rotation of the rocker circle alignment line and handle alignment point into a 45° angle line
5. Pull up the rocker ring and rocker cap vertically
6. Press the rocker cap against the 3D lever
7. Place the rocker ring pins against the handle alignment point as shown in the figure and press down
8. Rotate the rocker ring 45° clockwise to align the rocker ring alignment line to the handle alignment point to complete the replacement

Calibration rocker

Connected to the host state: Settings – “handle and sensor” – “calibration rocker” – press the rocker to be calibrated – “calibration rocker” – press the handle “X” button – press the handle “A” button – according to the screen prompts to complete the upward, downward, left, right and circle movement in turn.

Note: When the cursor bounces outside the innermost circle, press “B” to exit and correct it again.

AFTER-SALES SERVICE

Please follow our instructions for use strictly. If you encounter any problems during using it, you can contact us for consultation and solution. Our email is: service@nyxigaming.com, we will handle it for you within 24 hours.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>