HOLZMANN KAP 305JL Electric Double Bevel Sliding Mitre Saw User Manual

June 11, 2024
HOLZMANN

HOLZMANN KAP 305JL Electric Double Bevel Sliding Mitre Saw

KAP 305JL Electric Double Bevel Sliding Mitre Saw

Read the operation manual carefully before first use.

SAFETY SIGNS

ATTENTION! Ignoring the safety signs and warnings applied on the machine as well as ignoring the security and operating instructions can cause serious injuries and even lead to death.

READ THE MANUAL! Read the user and maintenance manual carefully and get familiar with the controls in order to use the machine correctly and to avoid injuries and machine defects.

EC-CONFORM: This product complies with EC-directives

General note

Protective clothing!

Stop and pull out the power plug before any break and engine maintenance!

Only trained staff!

Operation with jewelry forbidden!

Operation with tie forbidden!

Operation with long hair forbidden!

High voltage!

Warning about cut injuries!

SymbolProtect from moisture!

SymbolProtection class II!

SymbolLaser class 2!

ILLUSTRATION

ILLUSTRATION
ILLUSTRATION
ILLUSTRATION

ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION

TECHNIC

**1**  Back fence  **20** Back fence adjustment screws
**2** Slit **21** Back fence fixing knob
**3** Fixing knob **22** Sliding device fixing knob
**4**  Angle fixing lever **23**  Interlock knob
**5** Angle measuring scale **24**  ON-OFF-switch
**6** Laser **25** Security lock lever
7 Workpiece boom 26 Belt cover
**8** Compensation angle **27** Depth stop
**10**  Downholder **28**  Depth stop adjustment screw
11 Sliding bars 29 Adjustment screw for slot cut depth
12 Cover carbon brush 31 Saw blade
13 Transport handle 33 Dust bag
14 Handle 34 Pipe wrench
15 Saw blade protection 35 carbon brush replacement
16 type plate 36 Tilt angle indicator
17 Cable 37 Saw arm adjustment screws
18 Fixing knob tilt 38 Laser ON/OFF Switch
19 Tilt measuring scale ****
technical details

KAP 305JL


Motor power| 1800W (S1 100%), 2000W (S6 25%)
Voltage|
230V a.c. / 50Hz
Saw blade speed| 4200min-1
Saw blade| Ø 305mm
Boring|
Ø 30mm
Horizontal swing| -45° / 0° / +45°
Tilt|
-45° / 0° / 45°
max. cut| 0° x 0°: 330 x 115mm
max. cut| 45° x 0°: 240 x 115mm
max. cut| 0° x 45°: 330 x 85mm
max. cut| 45° x 45°: 240 x 85mm
Workpiece minimum size| **** L x H 30 x 5mm
weight| 23 kg
Sound-pressure-level LPA| 99,9dB(A)| K:3dB(A)
Sound-power-level LWA| 112,9dB(A)| K:3dB(A)
Vibration| 2,091m/s²| K: 1,5m/s²

PREFACE

Dear Customer!
This manual contains information and important instructions for the installation and correct use of the profimitre saw KAP 305JL.
Following the usual commercial name of the device (see cover) is substituted in this manual with the name “machine”.
This manual is part of the product and shall not be stored separately from the product. Save it for later reference and if you let other people use the product, add this instruction manual to the product.

Please read and obey the security instructions!
Before first use read this manual carefully. It eases the correct use of the product and prevents misunderstanding and damages of product and the user’s health.

Due to constant advancements in product design, construction pictures and content may diverse slightly. However, if you discover any errors, inform us please. Technical specifications are subject to changes!

Please check the product contents immediately after receipt for any eventual transport damage or missing parts.
Claims from transport damage or missing parts must be placed immediately after initial product receipt and unpacking before putting the product into operation. Please understand that later claims cannot be accepted anymore.

SAFETY

Intended Use

The machine must only be used for its intended purpose! Any other use is deemed to be a case of misuse.
To use the machine properly you must also observe and follow all safety regulations, the assembly instructions, operating and maintenance instructions lay down in this manual.
All people who use and service the machine have to be acquainted with this manual and must be informed about the machine’s potential hazards.
It is also imperative to observe the accident prevention regulations in force in your area.
The same applies for the general rules of occupational health and safety.
The machine is used for: cutting wood and plastic materials.
Any manipulation of the machine or its parts is a misuse, in this case HOLZMANNMASCHINEN and its sales partners cannot be made liable for ANY direct or indirect damage.
Even when the machine is used as prescribed it is still impossible to eliminate certain residual risk factors.

WARNING

  • Use only saw blades allowable for this machine!
  • Never use a damaged saw blades!
  • Use the machine never with defective or without mounted guard!
  • The removal or modification of the safety components may result in damage to equipment and serious injury!
    HIGHEST RISK OF INJURY!

Ambient conditions

The machine may be operated:
humidity max. 70%
temperature +5°С to +40°С (+41°F to +104°F)
The machine shall not be operated in areas exposed to increased fire or explosion hazard.

Prohibited use

  • DO NOT USE THE MITRE SAW FOR CUTTING FIREWOOD!
  • Do not operate the machine outside the stated technical restrictions laid down in this manual.
  • Do not operate the saw without security devices.
  • Do not dismount the saw blade protection.
  • Do not use the machine for cutting any other material than wood and wood composite products and plastic.
  • Do not manipulate the machine.
Security instructions

Missing or non-readable security stickers have to be replaced immediately!
The locally applicable laws and regulations may specify the minimum age of the operator and limit the use of this machine!
To avoid malfunction, machine defects and injuries, read the following security instructions!

Read the manual carefully and get familiar with all components before operating the machine for the first time.
This manual contains important information for correct operation of the machine.
This manual is part of the machine and shall be stored for later reference. Add this manual to the machine if handed to 3rd persons for use.
Stick to these Security Warnings and Instructions to reduce the risk of serious injuries.

Assure that the working area is sufficiently lighted!
Keep your work area dry and tidy! An untidy work area may cause accidents. Avoid slippery floor.
Do not overload the machine.
Provide good stability and keep balance all times.
Avoid abnormal working postures! Make sure you stand squarely and keep balance at all times.
Always stay focused when working. Reduce distortion sources in your working environment. The operation of the machine when being tired, as well as under the influence of alcohol, drugs or concentration influencing medicaments is forbidden.
The plug of an electrical tool must strictly correspond to the socket. Do not use any adapters together with earthed electric tools.
Each time you work with an electrically operated machine, caution is advised! There is a risk of electric shock, fire, cutting injury.
Avoid body contact with earthed.
Protect the machine from dampness (causing a short circuit).
Use power tools and machines never in the vicinity of flammable liquids and gases (danger of explosion).
Check the cable regularly for damage
When working with the machine outdoors, use extension cables suitable for outdoor use.
Do not use the cable to carry the machine or to fix the work piece.
Do not overload the machine.
You will work better and safer at specified power range.
Use the correct power tool.
Do not use low-power machines for heavy work.
Do not use the power tool for such purposes for which it was not designed. For example do not use hand circular saw for cutting tree limbs or logs.

Respectively trained people only and only one person shall operate the machine. Do not allow other people, particularly children, to touch the machine or the cable. Keep them away from your work area. Make your workshop childproof.

Wear suitable work clothes! Do not wear loose clothing or jewelry as they might be caught and cause severe accidents!
Wear a hair net if you have long hair. Loose objects can become entangled and cause serious injuries!

Use personal safety equipment: ear protectors and safety goggles when working with the machine.
Wood dust may contain chemical substances that have a negative impact on personal health. Work on the machine only in well-ventilated areas with suitable dust mask perform!
When working outdoors non-slip footwear is recommended.

Never leave the machine running unattended! Before leaving the working area switch the machine off and wait until the machine stops.
Always disconnect the machine prior to any actions performed at the machine. Avoid unintentional starting
Do not use the machine with damaged switch
Never use the power cord for transportation or manipulation of the machine!

Never leave Before starting the machine remove any adjusting wrenches and screwdrivers
Use a clip or clamping jaws to secure the workpiece
Do not fix the workpiece with your hands
Rotating parts can cause severe cut injuries
Keep the saw blades sharp and clean, so they get stuck less often and are easier to guide
Keep any machine that is not being used out of reach of children
Connect the dust extraction device to.
Do not use the cable to remove the plug from the socket.
Protect the cable from heat, oil and sharp edges.

SymbolEven Lasers with relatively small output can harm your eyes! Therefore:
Never look directly into the laser or into the laser beam!
Never direct the laser beam towards reflecting surfaces, persons and animals.
Do not manipulate the laser device!

Use only saw blades that are suitable for the use with the KAP machine, especially regarding technical parameters and which are tested and comply with the directive EN 847-1.
Deflected, defect or worn saw blades have to be replaced immediately.
SymbolBlunt saw blades have to be sharpened or replaced.
Blunt saw blades highly increase the danger of kickback!
Assure yourself that the saw blade is correctly mounted and does not touch the base plate.
Do not stop the saw blade by touching it on the side. This will ruin the drive mechanism.
Do not manipulate or remove the saw blade protecting cover!
Do not fix small workpieces by hand, instead only use the downholder (10).
No material feed, no material removal, no adjustments or other activities when saw blade is running.
Do not position your hands near the saw blade or in a way that they could slip into the cutting line.
Long workpieces have to be supported by the double bar guide.
Take especially care when cutting round workpieces!
Check the workpiece for nails, clamps and other material! Just cut one workpiece at once. Do not stack or attempt to cut several work-pieces in one cutting operation!
Do not cut firewood
Wear gloves when handling the saw blades and rough materials. It is recommended that saw blades, whenever practicable be carried in a container.
Make sure that the speed indicated on the saw blade is at least as high as that on the saw speed specified.
Be sure to use only those spacers and screw rings, which are suitable for the purpose specified by the manufacturer.
No Reload, remove or adjust workpieces, or material remains with the machine running!
Do not place hands in near circular saw blade or in a position where they could slip direction circular saw blade!
The use of other application tools and other accessories can mean a risk of personal injury.
Let your power tool repaired by a qualified electrician
The machine does not require extensive maintenance. If malfunctions and defects occur, let it be serviced by trained persons only.


|

N O T I C E

---|---

Emergency procedure

A first aid kit in accordance with DIN 13164 should always be readily available for a possible accident. Initiate the violation in accordance with the necessary first aid measures. When requesting support, provide the following details:

1. Place of accident| 2. Type of accident
3. Number of injured people| 4. Injury type(s)

Remaining risk factors

WARNING
It is important to ensure that each machine has remaining risks. In the execution of all work (even the simplest) greatest attention is required. A safe working depends on you!

Even if the machine is used as required it is still impossible to eliminate certain residual risk factors totally. The following hazards may arise in connection with the machine´s construction and design:
Despite of correct and proper use and maintenance there remain some residual risk factors:

  • Risk of injury to the hands / fingers by the rotating tool during operation.
  • Risk of injury due to sharp edges of the workpiece, especially in non-fixed with a suitable tool / device workpiece.
  • Risk of injury: hair and loose clothing, etc. can be captured and wound up! Safety regulations must be observed with regard to clothing.
  • Risk of injury due to contact with live electrical components.
  • Risk of injury due to breakage or cracking of the abrasive
  • Risk of injury due to dust emissions, treated with harmful agents workpieces
  • Risk of injury to the eye by flying debris, even with safety goggles.
  • Risk of injury to the hearing by prolonged labor without hearing protection.

These risk factors can be minimized through obeying all security and operation instructions, proper machine maintenance, proficient and appropriate operation by persons with technical knowledge and experience.

WARNING
This machine produces an electromagnetic field during operation. This field may under some circumstances interfere with active or passive medical implants. To reduce the risk of serious or fatal injury, we recommend persons with medical implants to consult their physician and the medical implant manufacturer before operating this machine!

ASSEMBLY

Delivery content

Please check the product contents immediately after receipt for any eventual transport damage or missing parts. Claims from transport damage or missing parts must be placed immediately after initial machine receipt and unpacking before putting the machine into operation. Please understand that later claims cannot be accepted anymore.

Assembly
  • Place the workpiece hold-down device (10) in the holder provided (see Figure A).
  • The workpiece boom (7) mount by mounting the compensation angle (8) between the two outrigger booms. Finally, you put the design into the holes which are positioned laterally on the base plate.
  • Insert the suction on the corresponding port on the back of the saw unit. Using the clamping lever to put the dust bag on the suction.
Transport

When bringing the machine to the workplace you have to prepare it for transport. These instructions have to be followed prior to every transport of the sliding compound saw

  • Disconnect the machine from the power supply.
  • Swing the saw arm into the lowest position and lock it in that position with the interlock knob (23).
  • Fix the saw arm with the sliding device fixing knob (22).
  • Lift the machine only at the transport handle (13).
Workplace requirements

The KAP 305JL sliding compound saw has to be attached to the underground. For this purpose there are 4 borings at the ground plate, two at the front side, two at the back side. Furthermore you can attach the machine to compound saw stands.

Operating a non attached saw poses a security risk!

OPERATION

Device to be operated in a perfect state only. Inspect the device visually every time it is to be used. Check in particular the safety equipment, electrical controls, electric cables and screwed connection for damage and if tightened properly. Replace any damaged parts before operating the device.

Operation instructions

|

WARNING

|


---|---|---
Perform all machine settings with the machine being disconnected from the power supply!

A T T EN T I ON

  • Do not look directly into the laser beam. Never direct the laser beam at people or objects other than the workpiece.

  • Do not deliberately point the laser beam at people.

  • Only point the laser beam at insensitive workpieces with a dull surface. Wood or rough surfaces are ideal for this. Shiny, reflective surfaces are not suitable for using a laser since the laser beam could be directed at the user by the reflective surfaces.

  • Always switch off the laser when you have finished work at the ON/OFF switch for the laser light (38).

  • Only switch on the laser beam if there is a workpiece on the mitre saw bench .

N O T I C E

  • Do not use damaged or warped saw blades.
  • Replace the worn table insert.
  • Select the appropriate saw blade for the material to be cut.
  • Warning! Protective equipment must not use for the purpose of transport
  • Use the saw only if the safety devices are functional, in good condition and in the provided position.
  • Do not remove offcuts or other workpiece parts from the sectional area, as long as the machine with unprotected blade is moving.
  • The workpiece must always be clamped to the saw table.
  • Before each cutting operation make sure that the machine stands safely.
  • Mark the cutting line on the workpiece.
  • Set the angle of the cutting operation.
  • To make a cut from the workpiece hold the laser along the marked line.
Modes

Angle settings
Tilt adjustment:

  • Loosen the fixing knob (18).
  • Set the saw arm in order that the tilt angle indicator (36) points exactly at 0° of the measuring scale (19).
  • Fix the saw arm in this position by tightening the fixing knob (18).
  • Bring the saw arm into the lower position and lock it with the interlock knob (23).
  • Attach an exact angle measuring device to saw blade side and ground plate. They should have an exact angle of 90°.
  • If not, then you need to adjust the 0° of the saw arm by adjusting it with the saw arm adjustment screws (N – 37).
  • Repeat the procedure until 0° on indicator is exactly 90° between saw blade and ground plate. Swing angle adjustment:
  • Loosen the fixing knob (3), operate the fixing lever (4) and swing the saw arm aggregate to the 0° position, let it click into place. You can see the angle at the measuring scale (5).
  • Swing the saw arm into the lower position and lock it with the interlock knob (23).
  • Attach an exact angle measuring device to saw blade side and the left back fence (1). They should have an exact angle of 90°.
  • If not, you need to adjust the back fence guide with the back fence adjustment screws (20) so that angle between saw blade and fence equals 90°.
  • Repeat the procedure with the right side back fence.

Adjust the cutting depth
Finally you need to check the cutting depth of the saw.
Swing the saw arm down into lowest possible position and check if it touches the ground plate.
The depth stop should be already preset so that the blade reaches into the cutting line slit (2) but has a distance to the ground plate of at least 5mm.
If necessary adjust the depth stop pin (27).

Laser
The Laser marks the cutting line. After having set all angles and cutting depth, you should finetune your laser. Attach the workpiece to the back fence, fix it with the downholder.
Perform a slot cut on the workpiece so that it gets not cut through entirely. (See point 5, Slot cut adjustments see point 5.3.3) Now turn on the laser (ON/OFF Switch 38) and check if the laser beam marks exactly the real cutting line.
If not you need to adjust the whole laser assembly until laser indication matches exactly the actual cutting line.

Operation

Switch on & prepare to cut

  • Connect the machine to the power supply
  • Read, understand and apply the security instructions.
  • Operate the accelerator lever (24) and wait until the saw blade has reached its full speed.
  • With the forefinger you now push the security lock lever to the left to unlock the moveable saw blade protection (25).

Switch off
As soon as you release the accelerator knob (24), the motor stops and the saw blade stops within 5-8 seconds.

 Operation modes

Miter cuts

  • Ideal for cutting short workpieces in miter and/or bevel angles.

  • For miter cuts fix the saw arm on the sliding bars with fixing knob (22).

  • Place the material to the back fence (1) and fix the material additionaly with the downholder (10).

  • Prepare to cut according to 5.1, perform the cutting operation.

  • Swing the saw arm back up, release the accelerator lever and wait until the electric saw brake stops the saw.

  • Now you can take the workpiece away 14.4.2 Sliding cuts

  • Sliding cuts are ideal for performing longer cuts

  • Fix the material!

  • Pull the saw towards your body.

  • Switch the machine on, wait until saw blade reaches full speed.

  • Now swing the saw arm down and let it work its way slowly through the material. Now push the saw arm slowly backwards.
    Advantage: If the material cracks or material parts are catapulted, then not towards the operator.
    Disadvantage: You MUST fix workpiece additionaly with downholder (10) to prevent it from kickback. 14.4.3 Slot cuts

  • Clap the depth stop (27) to the side so that the adjustment screw (29) touches the depth stop (27) when swinging down the saw arm.

  • Adjust the adjustment screw for slut cuts as desired (29).

OPERATION NOTICES

  • Always use well sharpened saw blades. Deflected, cracked or worn saw blades are a security risk and have to be replaced immediately!
  • Assure yourself that you do not overload the machine. Use it for operations it is designed for.
  • Choose always saw blades where at least 2-3 teeth are simultaneously in the material to achieve a clean cut and to reduce the risk of material kickback.
  • For precision miter and bevele cuts you should use a saw blade with at least 60 teeth.

MAINTENANCE


|

A T T E N T I O N

---|---
Don’t clean or do maintenance on the machine while it is still connected to the power supply:
Damages to machine and injuries might occur due to unintended switching on of the machine!
Therefore: Switch the machine off and disconnect it from the power supply be- fore any maintenance works or cleaning is carried out

The machine does not require extensive maintenance. If malfunctions and defects occur, let it be  serviced by trained persons only.
Before first operation as well as later on every 100 operation hours you should lubricate all connecting parts (if required, remove beforehand with a brush all swarfs and dust).
Check regularly the condition of the security stickers. Replace them if required.
Check regularly the condition of the machine.
The good condition and perfect adjustment is essential for a smooth and a clean cut. Store the machine in a closed, dry location.

N O T I C E
Clean your machine regularly after every usage – it prolongs the machines lifespan and is a prerequisite for a safe working environment. Repair jobs shall be performed by respectively trained professionals only!

Maintenance plan

Checks and activities to be performed


Loose or lost screws| Prior to every operation
Damage of any part| Prior to every operation
Saw blade condition| Prior to every operation
Clean machine| After every operation
Empty dust bag| After every operation
Readjust miter and bevel angle, laser;| monthly
Sharpen saw blade| When necessary
Change saw blade| When worn or defect
Change carbon brush| When carbon brush is worn ( < 4mm )

Change saw blade

In the following causes the blade to be changed:

  • You need to change to a different type of blade for better cutting result.
  • You replace a worn saw blade by a new one

ATTENTION: Use only saw blades with

  • max. diameter Ø of 305mm
  • max. thickness of 3mm
  • 25.4 mm inner diameter
  • max. RPM of the saw blade must be at least 4200min-1
  • Blade quality HSS or better

|

A T T E N T I O N

|
---|---|---
To eliminate the risk of cuts you should wear protective gloves when handling the circular saw blade

CAUTION:
To eliminate the hazard of cutting injury, you should wear safety gloves when touching the saw blade.

  • Swivel the movable circular saw blade guard backwards.

  • Turn the locking screw out so far that the safety pin can be pushed past.
    If the black guide plate is not easily turn loosen the retainer screw on the left easily.
    Change saw blade
    The sheet is pushed upward until the flange bolt is accessible

  • Press the shaft slightly and rotate the blade until the Spindle interlock system clicks.
    Change saw blade

  • Using the supplied Allen key you-6mm-solve with the flange bolt by turning it clockwise.
    NOTE: Left-hand thread !
    Change saw blade

  • Remove the flange bolt and flange.

  • Remove the blade from the motor shaft.

  • Install the new blade onto the spindle and pay attention to the right direction.

  • Place the flange on, turn flange screw with the Allen key laid back counterclockwise. Lefthand thread.

For Precision miter saw blades are recommended with teeth 60T!

Change the carbon brush

If your HOLZMANN KAP 305JL motor becomes loud or even does not start anymore, the carbon brushes are probably worn.
Remove with a screwdriver the carbon brush cover (30). If the carbon brush is worn (<4mm) you need to replace the 2 carbon brushes.
Memorize the direction of the carbon brushes when removing them. Take care to insert the new brushes similarly.
Run the saw for 10 minutes in idle run. Release the accelerator lever and observe the time interval required for the saw blade to stop. If it takes long time to stop (~ 20 seconds), then the electric saw blade brake does not work. Let the saw be checked by a professional.

Storaging

The machine never store outdoors! Storage permitted only at temperatures between + 5 ° and + 40 ° C, with at + 40 ° C the humidity must not be higher than 60%. Store in a dry, clean place

Cleaning

After each workshift the machine has to be cleaned. Remove chips etc. with a suitable tool. Do not remove them by hand (cutting injury!). Remove dust as well.

N O T I C E
The usage of certain solutions containing ingredients damaging metal surfaces as well as the use of scrubbing agents will damage the machine surface!
Clean the machine surface with a wet cloth soaked in a mild solution.

Disposal

Do not dispose the machine in residual waste. Contact your local authorities for information regarding the available disposal options. When you buy at your local dealer for a replacement unit, the latter is obliged to exchange your old.

TROUBLE SHOOTING

BEFORE YOU START WORKING FOR THE ELIMINATION OF DEFECTS, DISCONNECT THE MACHINE FROM THE POWER SUPPLY.

Trouble Possible cause Solution
Engine doesn’t run (or not correctly)
  • Switch defective

|

  • Repair switch

  • Power supply is off

|

  • Repair power supply

  • Carbon brushes defective

|

  • Chang carbon brushes

  • Motor defective

|

  • Repair or change motor

Saw blade gets stucked|

  • Blunt saw blade

|

  • Sharpening or changing

  • Too hard materal or too much pressure

|

  • Conform the cutting speed on work piece hardness and engine power

Material kickback|

  • Blunt saw blade

|

  • Sharpening or changing

  • Wrong running direction of the saw blade

|

  • Control

Wrong cutting angle Wrong mitre angle|

  • Wrong adjusted fence or saw aggregate

|

  • Control

Saw blade touches the machine bed|

  • Adjusting the cutting depth wrong

|

  • Control

MANY POTENTIAL SOURCES OF ERROR CAN BE CLEARED BY THE EXPERTLY  CONNECTION TO THE ELECTRICITY GRID.

N O T I C E
Should you in necessary repairs not able to properly to perform or you have not the prescribed training for it always attract a workshop to fix the problem.

WIRING DIAGRAM

WIRING DIAGRAM

Explosion drawing

explosion drawing

spare parts list

No

| Part Name| Qty| No| Part Name|

Qty

---|---|---|---|---|---
1| M5x14 screw| 9| 44| spring| 1
2| ∅5 washer| 12| 45| turnplate| 1
3| positive stop piece| 1| 46| bevel scale| 1
4| miter scale| 1| 47| ∅6 flat washer| 2
5| ∅2x4rivet| 3| 48| angle block| 1
6| M8x25 screw| 1| 49| ∅8 washer| 2
7| base| 1| 50| screw| 1
8| wrench sleeve| 1| 51| bracket| 1
9| wrench| 1| 52| bevel indicator| 1
10| ∅8 flat washer| 1| 53| M6 nut| 2
11| M8 lock nut| 1| 54| M6x25 screw| 2
12| steel piece| 2| 55| screw| 2
13| fence| 1| 56| M8 nut| 1
14| ∅8 flat washer| 4| 57| M10x50 bolt| 1
15| ∅8 spring washer| 4| 58| 1∅10 flat washer| 2
16| M8x35 screw| 2| 59| bevel lever| 1
17| M2x20 screw| 2| 60| M10 lock nut| 1
18| label 1| 2| 61| M10x86 bolt| 1
19| movable fence(left)| 1| 62| M10 nut| 1
20| movable fence (right)| 1| 63| spring| 1
21| M8x30 screw| 3| 64| M6x25 knob| 1
22| kerfboard| 1| 65|  |
23| M4x10 screw| 12| 66| ∅45x∅30×50 linear bearing| 4
24| grip| 1| 67| gasket| 4
25| M5x10 screw| 7| 68| bearing pressure cover| 2
26| lock lever plate| 1| 69| stopper pin| 2
27| lock pin| 1| 70| M4x8 screw| 8
28| cap| 1| 71| wire clamp| 2
29| miter lever| 1| 72| rear cover| 1
30| lock sleeve| 1| 73| screw| 5
31| ∅12 stop ring| 2| 74| slide| 2
32| compression spring| 1| 75| screw| 2
33| M6x14 screw| 5| 76| M6 lock nut| 2
34| ∅6 spring washer| 8| 77| support plate| 1
35| ∅6 flat washer| 7| 78| location sleeve| 2
36| lock cam| 1| 79| spring| 1
37| miter lock plate| 1| 80| rod| 1
38| lock lever| 1| 81| arm| 1
39| sleeve| 1| 82| screw| 1
40| ∅4 spring washer| 7| 83| height limit plate| 1
41| ∅4 flat washer| 2| 84| lock pin| 1
42| indicator| 1| 85| pin| 1
43| support foot| 1| 86| spring| 1
87| knob| 1| 134| brush holder cap| 2
88| label| 3| 135| motor housing| 1
89| blade case holder| 1| 136| label| 1
90| HK1010 needle bearing| 2| 137| screw| 1
91| axis| 1| 138| link plate| 1
92| key| 2| 139| location ring| 1
93| 6001 bearing| 1| 140| safty cover| 1
94| blade case| 1| 141| torsion spring| 1
95| spring seat| 1| 142| friction ring| 1
96| circlip| 2| 143| M6x10 screw| 1
97| torsion shaft| 1| 144| rubber cushion| 1
98| spring| 1| 145| screw| 1
99| spring hook| 1| 146| center plate| 1
100| M3x8 screw| 2| 147| cushion| 2
101| safty lock| 1| 148| wheel| 2
102| sheath| 1| 149| lower guard| 1
103| gasket| 1| 150| M5x8 screw| 4
104| spring| 1| 151| screw| 1
105| pin| 1| 152| circlip| 1
106| cover plate| 1| 153| M4x12 scew| 3
107| circlip| 1| 154| bearing cover| 1
108| driving wheel (big)| 1| 155| front end cover| 1
109| ∅6 spring washer| 1| 156| M5x16 screw| 3
110| screw| 1| 157| big gear| 1
111| belt cover| 1| 158| output shaft| 1
112| belt| 1| 159| 6003 bearing| 1
113| kerboard for table saw| 1| 160| gasket| 1
114| depth adjust nut| 1| 161| inner flange| 1
115| M6x35 screw| 1| 162| blade| 1
116| dust nozzole extension| 1| 163| outer flange| 1
117| dust nozzole| 1| 164| screw| 1
118| dust bag| 1| 165| cable plug| 1
119| M6x18 screw| 4| 166| upper handle| 1
120| M6x12 screw| 2| 167| ST6x25 screw| 2
121| driving wheel (small)| 1| 168| M5x20 screw| 3
122| label| 1| 169| M5x30 screw| 2
123| motor bracket| 1| 170| switch cover| 1
124| 6002 bearing| 1| 171| ST3.9×16 screw| 5
125| rotor| 1| 172| handle cover| 1
126| 6000 bearing| 1| 173| cable sleeve| 1
127| air seal ring| 1| 174| ST3.9×14 screw| 2
128| ST4.8×15 screw| 2| 175| cable clamp| 1
129| stator| 1| 176| handle| 1
130| ∅5 flat washer| 4| 177| spring| 1
131| M5x35 screw| 4| 178| switch button| 1
132| brush holder| 2| 179| swtich| 1
133| carbon brush| 2| 180| 606 bearing| 2
181| roller| 1| 195| handwheel| 1
182| rolling shaft| 1| 196| fence| 1
183| M8x30 screw| 1| 197| connecting plate| 1
184| lock plate| 1| 198| fence| 1
185|  | 1| 199| wrench| 1
186| M6x14 screw| 1| 200| sleeve| 1
187| M8x20 screw| 1| 201| spring pin| 1
188| side board| 2| 202| rivet| 4
189| foot screw| 1| 203| rod| 1
190| M8 nut| 1| 204| location rod| 1
191| rod| 1| 205| rivet| 2
192| support| 2| 206| transformer| 1
193| sleeve| 1| 207| laser seat| 1
194| pressure plate| 1| 208| laser| 1

CE-CERTIFICATE OF CONFORMITY

D i s t r i b u t o r

HOLZMANN MASCHINEN® GmbH

4170 Haslach, Marktplatz 4, AUSTRIA

Tel.: +43/7289/71562-0; Fax.: +43/7289/71562-4

www.holzmann-maschinen.at


name
PROFI MITRE SAW
model
KAP 305JL
EC-directives

  • 2006/42/EG
  • 2006/95/EG
  • 2004/108/EG
  • RoHs:2011/65/EU

applicable Standards
EN 61029-1/A11:2010, EN 61029-2-9:2009
EN 55014-1/A2:2011, EN 55014-2/A2:2008, EN 61000-3-2/A2:2009 EN 61000-3-11:2000, EN 60825:2007, EN 62321:2009

Hereby we declare that the above mentioned machines meet the essential safety and health requirements of the above stated EC directives. Any manipulation or change of the machine not being explicitly authorized by us in advance renders this document null and void.

Signature
Christian Eckerstorfer
techn. documentation
HOLZMANN-MASCHINEN
4170 Haslach, Marktplatz 4

Signature
Klaus Schörgenhuber
Director
Haslach, 03.04.2015
Ort / Datum place/date

GUARANTEE TERMS

(applicable from 03.04.2015)

Please consult our troubleshooting section for initial problem solving. Feel free to contact your HOLZMANN reseller or us for Customer Support!
Warranty claims based on your sales contract with your HOLZMANN retailer, including your statutory rights, shall not be affected by this guarantee declaration. HOLZMANN-MASCHINEN grants guarantee according to following conditions:
A) The guarantee covers the correction of deficiencies to the tool/product, at no charge, if it can be verified adequately that the deficiencies were caused by a material or manufacturing fault.
B) The guarantee period lasts 12 months, and is reduced to 6 months for tools in commercial use. The guarantee period begins from the time the new tool is purchased from the first end user. The starting date is the date on the original delivery receipt, or the sales receipt in the case of pickup by the customer.
C) Please lodge your guarantee claims to your HOLZMANN reseller you acquired the claimed tool from with following information:
> > Original Sales receipt and/or delivery receipt
> > Service form (see next page) filed, with a sufficient deficiency report

for spare part claims: a copy of the respective exploded drawing with the required spare parts being marked clear and unmistakable.
D) The Guarantee handling procedure and place of fulfillment is determined according to HOLZMANNs sole discretion in accordance with the HOLZMANN retail partner. If there is no additional Service contract made including on-site service, the place of fulfillment is principally the HOLZMANN Service Center in Haslach, Austria. Transport charges for sending to and from our Service Center are not covered in this guarantee.
E) The Guarantee does not cover:

  • Wear and tear parts like belts, provided tools etc., except to initial damage which has to be claimed immediately after receipt and initial check of the product.
  • Defects in the tool caused by non-compliance with the operating instructions, improper assembly, insufficient power supply, improper use, abnormal environmental conditions, inappropriate operating conditions, overload or insufficient servicing or maintenance.
  • Damages being the causal effect of performed manipulations, changes, additions made to the product.
  • Defects caused by using accessories, components or spare parts other than original HOLZMANN spare parts.
  • Slight deviations from the specified quality or slight appearance changes that do not affect functionality or value of the tool.
  •  Defects resulting from a commercial use of tools that – based on their construction and power output – are not designed and built to be used within the frame of industrial/commercial continuous load.

F) Claims other than the right to correction of faults in the tool named in these guarantee conditions are not covered by our guarantee.
G) This guarantee is voluntary. Therefore Services provided under guarantee do not lengthen or renew the guarantee period for the tool or the replaced part.

SERVICE

After Guarantee and warranty expiration specialist repair shops can perform maintenance and repair jobs. But we are still at your service as well with spare parts and/or product service. Place your spare part / repair service cost inquiry by filing the SERVICE form on the following page and send it:
via Mail to info@holzmann-maschinen.at o r via Fax to: +43 7289 71562 4

PRODUCT EXPERIENCE FORM

We observe the quality of our delivered products in the frame of a Quality Management policy. her product development and product choice. Please let us know about your:

  • Impressions and suggestions for improvement.
  • experiences that may be useful for other users and for product design
  • Experiences with malfunctions that occur in specific operation modes

We would like to ask you to note down your experiences and observations and send them to us via FAX, E-Mail or by post:

name :
product:
purchase date :
purchased from :
e – mail :
Thank you for your kind cooperation !

CONTACT:
HOLZMANN MASCHINEN GmbH
4170 Haslach, Marktplatz 4 AUSTRIA
Tel : +43 7289 71562 0
Fax: +43 7289 71562 4
info@holzmann-maschinen.at

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals