MAMA Under Sink Column Cover with 2 Doors and 2 Drawers Instruction Manual

INSTALLATION

INSTRUCTIONS

DO YOU NEED FURTHER HELP?
info@mamastore.it

All our products are delivered already assembled.

In order to ensure that the furniture is delivered in perfect condition, it is necessary for you to carry out certain actions such as adjusting the hinges, installing the feet, and fixing the hanging furniture to the wall.

Not knowing the type of wall you have in your home, we invite you to retrieve fischer screws suitable for the wall structure.

WHAT YOU NEED

SCREWDRIVER             SCREWDRIVER

FISCHER SCREWS SUITABLE FOR YOUR WALL     METER

SECURITY

The wall cabinets, mirrors, electrical and plumbing systems must be installed and/or connected by specialised personnel; Do not make any changes to the cabinet that would affect the stability of the structure; Do not overload the shelves with excessive loads (it is advisable to consider a maximum load of 2 kg); Do not use the shelves as support points to reach higher parts.

INSTALLATION

Have the furniture installed by specialised personnel, use expansion anchors of appropriate capacity and specific to the type of existing masonry. Check whether the masonry is suitable for suspended furniture (e.g. plasterboard).

MAINTENANCE

Always accompany the closing of doors and drawers; Place a protective cover between the surface of the furniture and any heat sources; Avoid direct contact with water on the wooden parts of the furniture; Avoid high humidity in the room where the furniture is located in order to avoid wood expansion and to prevent the edges from peeling off; Wood exposed to light may undergo colour variations; Do not write on the furniture and do not stick posters or stickers of any kind on it.

CLEANING

Take care and care when choosing furniture cleaning products (do not use chemicals or solvents, only a damp cloth and neutral soap is recommended). In special cases always test in places out of sight.

ERA113

INSTALLATION OF FEET

Package contents: N.2 FEET + N2. METAL CAPSULES + N.2 LOW FEET

Place the column cover on a flat surface at the side. Using a hammer, insert the metal caps from the inside of the cabinet into the holes on the back of the base of the column cover. Screw the wheels to the desired height from the outside of the column cover.
Install the two low plastic feet in the holes in the base.

INSTALLATION HANDLES

Use the prefixes on the drawers and doors to install the handles. Use the shorter screws for doors, the longer ones for drawers.
The handles are screwed in from the inside of the drawer/door. Use white hole covers to cover the visible holes inside the cabinet. Use the pads on the inside of the drawer/door to dampen noise.

SUSPENDED BASE INSTALLATION

FOR THE PRODUCTS ATENA60 – ATENA80 – ATENA100 – ERA60 – ERA80 – ERA100 – ATENA260 – ATENA280 – GEA1 – GEA2

The hardware package contains:

    NO. 2 ANGLE PLATES
NO. 3 PIGTAILS FOR FISCHER
    NO. 5 FISCHER D10MM
NO. 2 SCREWS 6X60 FOR FIXING CORNER WALL PLATES
      NO. 4 SCREWS 3.5 X 16 FOR FIXING PLATES ANGLES TO THE BOTTOM OF THE CABINET

IMPORTANT: INSERT THE FISCHER INTO THE HOLE OF THE ANGLE PLATE

IN THE EVENT OF A TIP-OVER OR FALL, THE CABINET CAN CAUSE SERIOUS, EVEN FATAL INJURIES. TO AVOID THIS RISK, THE FURNITURE MUST BE PROPERLY SECURED TO THE WALL. THE METHOD OF FIXING DEPENDS ON THE TYPE AND STRENGTH OF YOUR WALL, SO ANY FIXING MATERIAL (E.G. DOWELS, HOOKS, SCREWS) THAT MAY BE INCLUDED IN THE PACKAGE IS PROVIDED PURELY AS AN INDICATION AND SHOULD THEREFORE BE CHECKED AND REPLACED AS NECESSARY. WE STRONGLY RECOMMEND THAT YOU CONTACT YOUR OWN SPECIALISED PERSONNEL TO DEFINE THE CHOICE OF THE CORRECT ACCESSORIES. THE CABINET MAY REQUIRE THE CONNECTION OF ELECTRICAL AND/OR HYDRAULIC PARTS. INSTALLATION MUST BE CARRIED OUT IN ACCORDANCE WITH CURRENT REGULATIONS BY QUALIFIED PERSONNEL.

1. Mark on the wall where to drill the holes (two for the fischer with hook – top of the cabinet, and two for the angle brackets bottom of the cabinet)

2. With a drill, drill holes in the marked places using a drill bit of the same diameter as the dowel.

3. Fix the corner plates to the wall at the bottom as shown in the figure.
   No. 4 screws 3.5 x 16 for fixing plates

4. Support the base and fasten the attachments to the wall hook.

5. Use the two screws on the brackets to adjust height and distance from the wall.

6. Fasten the cabinet base to the corners.

7. Cover the brackets with the plastic caps corners at the bottom of the cabinet

WASHBASIN DRAINS

FOR SARA75 FURNITURE        FOR ATENA, ERA, GEA1 E GEA2 FURNITURE

ERA – GEA

HANDLE/TOWEL INSTALLATION

Use the prefixes on the drawers to install the handles.

The handles are screwed in from the inside of the drawer.

There are no pre-drilled holes for the towel rail.
Once the installation position has been chosen, mark with a pencil where to drill the holes.
Drill the holes with a drill with a diameter similar to that of the supplied screw. Screw in the towel rail from the inside of the drawer

ATENA – GEA

WOODEN CANVAS DRAWER AND GUIDES

The drawer on our furniture is made of canvas wood and has a cushioned runner. Here are the details should you need to remove or reinstall it.

Remove the top drawer by sliding the white lever at the bottom towards the centre. Lift the drawer slightly and remove it. (Fig.1)
Reposition the drawer by securing it through the rear holes (Fig.3) to the hook on the rail (Fig.2)
Secure the front part of the drawer by inserting the adjusting screw (Fig. 1) into the hole in the side of the drawer.
Slide the white lever towards the side of the cabinet.

PANORAMIC MIRROR ERA – ATENA – GEA

Take the distance between the centre of the two holes on the back of the mirror. With the help of a spirit level, mark the distance of the two holes on the wall. Take the distance between the centre of the two recesses on the back of the mirror.
With the help of a spirit level, mark the distance of the two holes on the wall and drill the holes with a drill bit compatible with the fischer provided. Insert the fischer screw with hook into the hole.
Insert the plastic support into the slots on the rear panel of the mirror. Use the two screws provided to secure it to the panel.
Install the 4 corner brackets on the panel, using the screws provided, to secure the mirror support.
Install the mirror on the wall.
All steps are mandatory to ensure safety.

LED LAMP

Luminaire intended for indoor use only.
Installation may require the involvement of qualified personnel.

Switch off the power supply at the main switch of the electrical system before mounting and any other maintenance work on the luminaire; Place the luminaire on the mounting surface and secure it with screws using the holes provided;

Secure the external cable of the luminaire to the frame with the cable clamp provided;
Connect the luminaire output cables to the general power supply cables (230 V) via a junction terminal block, taking care to match the conductors; Switch the power supply back on at the system’s main switch.

WASHTUB INSTALLATION

Fasten the washbasin to the wall with the fischers provided.
Apply neutral silicone along the upper edge of the washbasin and place the tub on it. Allow to dry.

MOUNTING OF FEET

WASHBASIN BASES, WASHBASINS, MULTIPURPOSE IN GENERAL

Esempio di multiuso con piedino quadrato

What will you find in the package?
Pack of number 4 feet with accompanying screws
Before assembly close cabinet doors and/or drawers, place it horizontally on a flat surface
Screw the feet with their screws into the holes provided in the base of the cabinet.
Screw the foot (with the removable part inserted) to the screw already present on the cabinet.
There is no need to drill further holes in the cabinet for the 4 corner holes on the leg; we use these for other types of furniture.
Should you also wish to use the 4 corner holes, please note that you will not find the corresponding holes on the cabinet, but will have to drill them yourself.

ADJUSTABLE ATTACHMENT FOR MIRRORS, WALL UNITS AND COLUMNS

FOR COMPOSITION SARA – ATENA – ERA – GEA – AT001 – AT002 – ER001

 More instructions at Suspended base installation

PUSH AND PULL ADJUSTMENT

The push and pull system will arrive already installed and consists of:

• plunger
• base

If adjustment is required (= if pressed, it does not lock), simply turn the plunger.

Disassembling the push and pull system:
Push down the baseplate through the claw on the
outside

1. Simultaneously push the plunger upwards, levering the body that mounts on the baseplate

SINGLE AND DOUBLE WALL UNITS AND MIRRORS

FOR PRODUCTS AT164SRI – AT163SRI – AT371SRL – AT372SRL – AT004 – AT005 – AT006 – AT007 – AT208 – ER003

IMPORTANT
FOR WALL MOUNTING, USE WALL PLUGS COMPATIBLE WITH THE TYPE OF WALL
WARNING
ELECTRICAL INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED TECHNICIAN, OBSERVING THE SAFETY DISTANCES REQUIRED BY LAW FOR THE DEGREE OF PROTECTION TO WHICH THE SYSTEM IS CERTIFIED

1. Retrieve fischer suitable for the wall type
2. Measure the distance between the A-points of the two plates
3. Mark two points on a wall at the correct distance.
4. Use a drill with a drill bit compatible to the type of fischer
5. Install the wall cabinet/mirror

LED SPOTLIGHT

Luminaire intended for indoor use only.
Installation may require the involvement of qualified personnel.
Acting on the main switch of the electrical system, switch off the power supply before mounting and any other maintenance work on the light fitting;
Place the luminaire on the mounting surface, taking care to feed the power supply cables through the recessed hole and press down until the luminaire is inserted;
Secure the external cable of the appliance to the frame with the cable clamp provided;
Connect L=brown coloured conductor and N=light blue coloured conductor by means of a terminal block to the respective conductors of the electrical system as shown in the diagram in the instructions and secure the terminal block once the connections have been made;
Switch the power supply back on at the system’s main switch.

DRAWERS AND SHOE CABINETS

MOUNTING SHOE CABINETS’ FEET

Esempio di scarpiera a ribalta con piedino triangolare

What will you find in the package?
Pack of number 4 feet with accompanying screws
Before assembly close cabinet doors and/or drawers, place it horizontally on a flat surface
Place the template, previously cut out, on each of the 4 corners at the base of the cabinet.
of the cabinet, pre-drill the holes A in the template with a screwdriver to facilitate insertion of the screws.
Screw the feet with their screws into the holes provided in the base of the cabinet.
Carefully lift the cabinet and install it in the chosen location.

ASSEMBLING DRAWER FEET

What will you find in the package?
Pack of number 4 feet with corresponding screws
Before assembly close cabinet doors and/or drawers, place it horizontally on a flat surface
Screw the feet with their screws into the holes prepared at the base of the cabinet, positioning the hollow part in contact with the cabinet base as shown in the figure.
Carefully lift the cabinet and install it in the chosen position.

HINGE REGISTRATION

YOU HAVE JUST INSTALLED THE CABINET AND THE DOORS ARE CROOKED? DON’T WORRY, JUST ADJUST THE HINGES

The hinges have three distinct adjustments required to align the doors to the cabinet frame. Thanks to the hinges, it is possible to move the doors noticeably outwards or inwards, from left to right, and finally, upwards or downwards.

Unscrew the indicated screws and move the sash up or down to adjust it. Fasten it again.
Unscrew the indicated screw and move the sash inwards or outwards to adjust it. Fasten it again.
Unscrew the indicated screw and move the sash to the right or left to adjust it. Fasten it again.

ANTI-TIP SYSTEM

The anti-tilt system prevents the cabinet from tipping over, thus ensuring safety in its use.
Fix the cabinet to the wall as shown in the figures in sequence.
FISCHER d. 08MM NOT SUPPLIED (BUY ACCORDING TO TYPE OF WALL)
What will you find in the package?
no. 1 angle plates with adjustment slots
no. 1 long screws for fisher
no.1 short screws
no.2 washers

Adjust the slot of the angle plate.
Fasten the slot to the wall using a fisher suitable for the type of wall.
Tighten the screw at the adjustment slot so that the cabinet is secured.

CORRECT AND SAFE LAMP LOCATION

IP44-certified lamps can be installed in Zone 2 and Neutral Zone.

At the end of its life it is “Waste Electrical and Electronic Equipment” (WEEE). Recycling means respecting the environment and the law (DIR96/02/EEC): find out about the separate collection points provided for by law (in Italy abuse is punishable under Art. 50 et seq. of Legislative Decree 22/1997). Product packaging must be disposed of according to the regulations in force in the municipality where the product is unpacked. Packaging materials can be dangerous (risk of suffocation), do not leave them within the reach of children.

DO YOU NEED FURTHER HELP?
info@mamastore.it

Documents / Resources

| MAMA Under Sink Column Cover with 2 Doors and 2 Drawers [pdf] Instruction Manual
Under Sink Column Cover with 2 Doors and 2 Drawers, Under Sink, Column Cover with 2 Doors and 2 Drawers, 2 Doors and 2 Drawers, 2 Drawers
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>