Losfom EM0 Body Camera User Manual

Losfom EM0 Body Camera

PREFACE

We sincerely thank you for using our company’ s product. This manual is the introduction of the body police camera which includes its functions, features, external structure, operation, and caution items. Before using the product, please read the user manual carefully and keep it properly.

PART 1 STRUCTURE DIAGRAM

1. Red Flashing Light
2. Infrared Lights
3. Video/Night Vision Button
4. White Light
5. Photo Button
6. Working Indicator
7. White Light Button/Alarm Button
8. Lens
9. Blue Flashing Light
10. Infrared Lights
11. Microphone
12. Image Sensor
13. Power Indicator
14. Speaker Hole
15. Reset Hole
16. USB/Charging Interface
17. LCD Display
18. Audio Button
19. Power On/Off Button
20. Menu/OK Button
21. Up/Mark Key
22. Down/Playback Button
23. Return Button

PART 2 LCD INDICATION

1. Video Icon
2. Resolution
3. Device ID & Police ID
4. System Date
5. System Time
6. Battery Icon
7. Audio Icon
8. TF Card
9. Current Video Recording Length

PART 3 BASIC OPERATION

How to charge the device

Low battery prompt: When the battery voltage is too low, the screen will intermittently display the words “Battery Low” with a prompt sound, and it will automatically shut down after 5 minutes. Please charge it in time it the battery is low, so as not to affect your use. If idle the camera for a long time, please charge it every two months. When need to use it, please charge it fully first. There are two ways to charge this product: Method 1:Using the USB cable and charger to charge. Method 2:Connect to computer to charge. As shown in the below position, use the USB cable to connect t the computer. When charging, the working indicator light shows green, the power indicator light shows blue, and the blue indicator goes out after fully charged.

Power On/Off/Standby Mode

Power On: In the shutdown state, press and hold the CO button to power on, and enter the preview screen, the working indicator shows green. Turn on the LCD Display function in the menu, if without any operation after 5 minutes after powering on, the default is to automatically enter the LCD Auto Off mode. Start video recording for 5 minutes, without any other operations, then it automatically enters the LCD Auto Off mode and the red indicator keep flashing. (LCD Display option can be set to off/30 seconds/1min /2min/5min).

Power Off: In the power-on state, press and hold the button for 3 seconds to power off, and all the indicator lights go out.
Standby Mode: In the power-on state, the power indicator stays green. Turn on the LCD Display option in the menu, if without any operation after 30 seconds/1min/2min/5min after powering on, the screen will turn off. Tap any button to light up the display screen.

Take Photo

In the power-on state, short press the button to take a picture and automatically save it. There will be a “click” sound during the picture. The picture is named after the date and time, and the suffix is JPG. Short press button to enter the playback mode. (When the icon turns from o toA, the photo is taken successfully)

Video Recording

Normal Video In the standby mode with the preview screen, tap the button to start the video record OR in power off state, long press Čbutton for 3 seconds to start video recording. When recording. there is a red dot flashing slowly in the screen upper left corner, and the work indicator shows red flashing Press the button again to stop recording, the indicator turns back to steady green, the video file is automatically saved and the camera automatically returns to the preview screen. The video is named after the date and time, with AVI as the sufix. Short press ( button to enter the playback mode.

Snapshot
During the recording process, short press O button to take a picture and save it automatically. The video recording ill not be interrupted during this process.

Video Lock/Mark Press button to start the video recording, click the button to lock the current video and mark it as a key video, then need to click video button again to save this key video. This function will not interrupt the video process. The marked videos will be saved and the video file name starts with “SOS”. During the video recording, click the button to lock the current video and click the button again to release the lock. Then press ČË button to save the file. This video will save as a normal video, named beginning as “NOR” Please check the below picture:

If marked the video as a locked video, this file will not be covered after the memory is full during the Loop Recording/Cyclic Record mode. And the locked videos can’t be deleted from the camera.

Audio Recording

In the power-on state, tap the button; OR long press and hold the button for 3 seconds in the power-off state, to start an audio recording. When recording, the screen displays a logo, and the work indicator flashes red and green. Press the button again to stop the audio recording The work indicator goes off and the audio file is automatically saved. The camera automatically returns to the preview screen. The indicator turns to steady green light. The audio is named after the date and time, with .WAV as the suffix. Short press (button to enter the playback mode.

Night Vision

The infrared night vision function defaults to “Manual”, and the infrared night vision light is off, which is suitable for daytime use. For night use, need to manually switch to infrared night vision mode. In the power-on state, long press the button to turn on the IR mode. At this time, the six infrared lights are turned on and appear red. The preview screen or the image changes to black and white. Long press the itton again to turn off the IR mode. IR lights turn oft, and the preview Screen or the image will be restored to the color one. If need the camera to switch automatically, enter the menu to set IR Filter to “Auto”. Then the camera can automatically switch the intrared night vision mode according to the brightness of the environment.

Files View /Playback

• In the standby mode, short press the ( button to enter the playback menu, and use the () button or button to select the desired option, as shown in the figure below:
• Press the button to enter the playback list, and use the button or the (button to select the file to be played;
• Press the (button to view and press the button to return to the previous menu.

File Deletion

Note: If you need to protect the recorded files, turn on the “Password” option in the menu setting. Otherwise, all the files can be deleted without password verify.
After turn on the “Password ” option in the menu setting, need to enter the default password: 000000 first before deleting files. The locked/marked video can’ t be deleted on the camera’ s side, other files can be deleted normally. Step as

• In standby, short press ( button to enter the playback mode.
• Use the button or button to choose the Video/ Photo/ Audio file need to delete, click ( button to the playback file list.
• Long press (button to the password verify page, insert the default password(000000) if first use (otherwise, enter the password you have modified).
• After that get the option of “cancel” or “ok” interface, use the button or button to choose “cancel” or “ok”, then click button to confirm. After deleting the file, the camera goes back to the previous playback file list.

File Transfer/Connecting Computer

Connect to the computer by the USB cable attached. Then enter USB disk mode. If turn on “Password”option in the menu, need to input the password you set first, (the default password is 000000) then could review or delete the files in the Computer.

Camera Password

Default Camera Password: 000000 There is “Password” option in the menu setting, click button in the standby mode to get into menu, then turn to “Password” function. If want to turn it on, you need to insert the defau lt password: 000000 first. Click button again, then use the button or button to choose the “On” option and click button again to save the change. After turning on the “Password ” option, the below circumstance need to verify the password, including but not limited to:

1. When connecting the camera to the PC side;
2. Try to delete the files on the camera;
3. Choose to change the camera password, need to verity the old password(f the neW camera, need to enter the default password.)

How to change the password?
Short press button in the standby mode, then turn to “Change Password” section in the menu. Before changing, you need to insert the default password: 000000 first. Then use and button to choose the 6 character password you desired, then need to click button to save the change.

Reset

When the device crashes or stops working due to improper operation or other special reasons, please press the button to reset the device. Then re-power the camera to check.

PART 4 SYSTEM SETTING/ MENU LIST

In standby mode, press the button to enter the setting menu. After entering the menu interface, use the button and button to select the list to be set, press the button to confirm. Use the button or ( button to change the options, then press the button again to confirm and save the setting changes.

PART 5 WORKING INDICATOR LIGHT

• In the power-on state, camera standby, the power indicator shows steady green;
• On the video mode, the working indicator light is red and flashes slowly;
• On the audio mode, the working indicator is red and green and flashes slowly;
• Connecting a camera to the computer, the work indicator is green, the power indicator is blue;
• When charging, the power indicator is blue, and the light will be off when fully charged. If charging when powering on, the power indicator shows blue and working indicator shows green;
• After powering on, every time a photo is taken, the Work indicator tlashes red once;

PART 6 WHITE LIGHT &ALARM FUNCTION

White Light After powering on, long press thebutton to turn on /off the white light, the camera emits white light, which acts as an illuminating light.
Red & Blue Flashing and Alarm After powering on, tap the .=|button to turn on the alarm function. The camera will sound an alarm and flash red and blue warning lights. Press the button again to turn off the alarm sound, and tap it again to turn off the flashing lights.

PART 7 DASH CAMERA MODE

In standby mode, press the button to enter the setting menu. Use the button and button to get the Car Dash Cam Mode option, press the button to get the two options of “off and “On”. Press the button or button to change the option to “On”, then press the button again to confirm and save the change.

Package includes a Car Suction Cup Bracket to install the body camera on the car windshield. This suction cup only support the clean and smooth glass material. If the surface is not smooth enough or frosted glass can not suck firmly.

Instructions to install

PART 8 SPECIFICATIONS

PART 9 TROUBLESHOOTING

The camera couldn’t power on, does it stop working?
A:

1. Connect the charger and cable to charge the device, and check whether the problem is solved after 4 hours of charging
2. Please check whether the charging interface and the USB cable are normal,
3. Use a pin to do a reset of the camera and re-power on to check again;
4. If the problem cannot be solved, please contact Customer service for further help.

Q: The image shot by the device is red/ green. Or the screen has color difference.
A: Please shut down the camera and restart it to check.

Q: Why the screen turns off automatically?
A: The camera enters the LCD Auto Off mode in default without 5 minutes operation. If you want the display is always on, please enter the menu to set LCD Display option to Off. LCD Display option can be set to oft/30 sec/1 min/2 min/5 min.

Q: Why does the camera shut off auto?
A: Please check whether the Auto Power Off option in the menu is on. It you want the camera to stay power-on state, please enter the menu to set Auto Power Off to Off. Auto Power Off mode can be set to off/3 min/5 min/10 min.

What does the Stealth Mode/Secret Mode in the menu mean?
A: The Stealth Mode/Secret Mode is default Off in the menu. If turn it on, when recording video/audio/ taking photos, the indicator light and sound won’t appear, realize the hidden recording.

Q:A video or audio cannot be played?
Or no sound for videos? A: Please check the menu and turn on the “Video sound option. Turn to the loudest volume of the camera to check whether the sound could playback normally with the camera itself. It is recommended to playback videos/ audio on the VCL media player on your computer.

PART 10 PACKAGE LIST

PART 11 CUSTOMER SERVICE

Losfom is always dedicated to offer the best service to our valuable customer. To reach the customer service, please e-mail us: Official Email address: support01@losfom.com

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician help.

The device has been evaluated to meet general RF exposure requirement. The device can be u sed in portable exposure condition without restriction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>