PHILIPS 4116231P6 Hue Enrave LED Ceiling Light Instructions
- June 11, 2024
- Philips
Table of Contents
4116231P6 Hue Enrave LED Ceiling Light
Instruction Manual
4116231P6 Hue Enrave LED Ceiling Light
Warnings
Always make sure the luminaire is detached from the mains socket
Always make sure the DC cable is detached from the power supply
Staring at the operating light source may cause eye injury
| # | Disassemble/dismantle steps | Tools needed |
|---|---|---|
| a | Press and rotate diffuser [27) by hand counterclockwise until it | |
| unsnap.Lift the diffuser up to remove it from base [30) | – | |
| b | Remove deco rinq [26) by lifting up from the base (30] | – |
| c | Unplug wires from light source-led modules [11] | WAGO TOOL #2060 |
| d | Unplug wires from light source – splitter [10] | WAGO TOOL #2060 |
| e | Remove flat cable from the light source – splitter [10] and light source – | |
| hue connect [9) | – | |
| f | Unscrew 2 screws [21) and remove pull relief [17] from base[30] | TORXHEAD |
SCREW DRIVER T10
g| Unplug wires from power supply cord [32] and light source – hue connect
(9]| RATHEAD SCREWDRIVER OR WAGO TOOL #2065
h| Unscrew 1 screw [8] and remove light source-hue connect [9)| TORXHEAD SCREW
DRIVER T10
i| Unscrew 2 screws [8] and remove light source – splitter [101| TORXHEAD
SCREW DRIVER T10
j| Unscrew 14 screws [8) and remove light source -led modules [11) and plates
[31] from base [30)| TORXHEAD SCREW DRIVER T10
k| Unscrew 3 screws [19) and remove washers [6] and plate [29] from base [30)|
TORXHEAD SCREW DRIVER T10
I| Remove grommet [15) from plate [29)| –
m| Unscrew knurled parts in connection parts [3] press and remove 3 suspension
cables from them and pull out them through holes in plate| –
n| Pry and remove plate (29] from base [30)| –
o| Unscrew 2 screws [16) and remove bracket (24) from the base [25)| CROSSHEAD
SCREWDRIVER PH
p| Unscrew 6 screws [19) and remove caps [7] from base [25)| TORXHEAD SCREW
DRIVER T10
q| Unscrew 3 nuts [2] and remove connection parts [3) and washers [1] from
base [251| SOCKET WRENCH
r| Unscrew 1 screw [13] and remove it from base [25)| CROSSHEAD SCREWDRIVER PZ
s| unclamp 2 close end connectors and loosen wires from control clear – psu
[23) and power supply cord [32]| PINCER
t| Remove terminal blocks [12] by unscrewing wires of the control gear – psu
[23),remove cover N (18) and cover L (22)| FLATHEAD SCREWDRIVER
u| Unscrew 2 screws [19) and remove control gear – psu (23) from the base
[25)| TORXHEAD SCREW DRIVER T10
v| Unscrew 2 screws (20) and remove power supply cord [32] from the base (25)|
TORXHEAD SCREW DRIVER T10
w| Unscrew 1 nut [2) and remove pull relief [14] and nipple [4] from base
[25]| SOCKET WRENCH
| COMPONENT| QTY
---|---|---
1| Washer| 3
2| Nut| 4
3| Connection part|
4| Nipple| 1
5| Suspension cable| 3
6| Washer| 3
7| Cover| 3
8| Screw| 17
9| Light source – hue connect| 1
10| Light source – splitter| 1
11| Light source -led module| 7
12| Terminal block| 2
13| Screw| 1
14| Pull relief| 1
15| Grommet| 1
16| Screw| 2
17| Pull relief| 1
18| Cover N| 1
19| Screw| 11
20| Screw| 2
21| Screw| 2
22| Cover L| 1
23| Control gear – psu| 1
24| Bracket| 1
25| Base| 1
26| Deco ring| 1
27| Diffuser| 1
28| Plate| 1
29| Plate| 1
30| Base| 1
31| Plate| 7
32| Power supply cord| 1
SKU| Color| Country
---|---|---
915005998001| White| EU/UK
915005998101| Black| EU/UK