DALS Lighting 9009CC Series 120V LED Linears Instructions
- June 11, 2024
- dals Lighting
Table of Contents
Instructions for 120V LED linears
9009CC /9012CC / 9018CC / 9024CC / 9030CC
Instructions Manual
IMPORTANT SAFETY INSTRUCTIONS
-WARNING-
Instructions pertaining to a risk of fire, electric shock or injury to
persons.
These products may represent a possible shock or fire hazard if improperly
installed or atached in any way. Products should be installed in accordance
with these instructions, current electrical codes and/or the current National
Electic Code (NEC). To reduce the isk of fire, eleciric shock or injury to
persons; use oy nsulated staples or plasic ties to secure cords, route and
secure cords so that they will not be pinched or damaged when the cabinet is
pushed to the wall, position the poriable cabinet light with respect to the
cabinet so the lamp replacement markings are able to read during relamping.
Not ntended for nstallation in ceflings or soffs. Intended inside “buit-n
furnishings” such as a kitchen cabinet or lrophy case. The National Electrical
Code (NEC) does not permit cords to be concealed where damage to insulation
may go unnoticed. To prevent fire danger, do not run cord behind walls,
ceilings, offis or cabinets where it may be inaccessable for examination,
cords should be examined periodically and immediatly replaced when any damage
is noted.
This class B digital apparalus complies wilh Canadian ICES-005. This digital
apparalus does not exceed the Class B imits for radio-noise emissions from
digital apparatus as set out in the Radio Inerference Regulations of the
Canadian Depariment of Communications.
| Lumens per fixture at 3000K| Total consumption
---|---|---
9009CC:
9012CC:
9018CC:
9024CC:
9030CC:| 200
335
560
850
1115| W
5W
8W
12W
16W
**** Model 9009CC is plug-in only and comes with three selectable CCTs: 2700K, 3000K, 4000K
Compatible extension cords (sold separately):
9000-ACCE24: – 24″ (61 cm) extension cord to connect between two 120V LED
linears
9000-ACCE72: – 72″ (183 cm) extension cord to connect between two 120V LED
linears.
**Warranty:
**
DALS offers a 5 years warranty for the LED linear light from the date of
purchase that covers repair or replacement of defective parts of the housing,
optics, and electronics.To contact DALS customer service call to 1 877 430
1818 or send an e-mail to info@dals.com.
For more information on new products, technical specifications and additional
accessories visit our website: www.dals.com
Directional Lighting
Approved for installation inside, under or over cabinets, with light shining
in any directions.
Switch
5 Color temperature setting options (models 9012, 9018, 9024, 9030)
3 Color temperature setting options (model 9009)
High / Low / OFF switch
Interrupteur 2
Installation instructions
-
PLUG-IN OR DIRECT WIRED
Install the screws on mounting surface to the dimension specified above.
Leave 1/16″ (1.5 mm) spacing between screw head and mounting surface. -
ONLY FOR DIRECT WIRED
Unscrew the cover and remove it to make connections.
Remove the appropriate knockout than install the included strain relief bushing. -
ONLY FOR DIRECT WIRED
Install the 120V line feed wire by matching the black wires together, the white wires together and the ground wires together. -
PLUG-IN OR DIRECT WIRED
Plug-in: put the fixture in place and connect the power cord to the fixture.
Direct wired: screw the cover and put the fixture in place. -
PLUG-IN OR DIRECT WIRED
Plug others fixtures with the included extensions cord or seamless connector.
Linears can be linked together up to a maximum of S00W per circuit.
The first linear of a serie Is the only one to be plugged in or direct wired.
INS_900XCC_REV10
1877430 1818
Documents / Resources
| DALS
Lighting 9009CC Series 120V LED
Linears
[pdf] Instructions
9009CC-WH, 9009CC Series 120V LED Linears, 9009CC Series, 120V LED Linears,
LED Linears, 120V Linears, Linears
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>