HUANANZHI X99-T8 Gaming Motherboard User Manual

HUANANZHI X99-T8 Gaming Motherboard

Product Information

The SZ HUANAN SANXIAN TECHNOLOGY CO., LTD. motherboard is a high-performance motherboard designed for gaming and other high-end applications. It supports DDR4 RAM with a capacity of up to GB and clock speeds of ///MHz. It features multiple I/O ports including SATA, SATA, USB, PS/, RJ, and PCIe. The motherboard also includes Realtek LAN and audio drivers for high-quality sound and network connectivity.

Product Usage Instructions

Installation

1. Ensure that all components are compatible with the motherboard before installation.
2. Install the CPU onto the LGA-CPU pin of the motherboard.
3. Insert the RAM*DIMM into the appropriate slots on the motherboard.
4. Connect the necessary cables to the I/O ports on the motherboard.
5. Secure the motherboard onto the case using screws.

Drivers Installation

1. Insert the provided driver installation CD into your computer’s CD drive.
2. Locate and run the X-T chipset driver and follow the installation instructions.
3. Install the Realtek sound card driver and LAN driver for high-quality audio and network connectivity.
4. Install any other necessary drivers for your specific components.

BIOS Settings

1. Power on your computer and press the Delete key to enter the BIOS setup.
2. Navigate through the BIOS settings using the arrow keys.
3. Adjust settings as desired for optimal performance.
4. Save changes and exit the BIOS setup.

Note: Please refer to the user manual for additional safety precautions, packing information, motherboard diagram, and other installation and setting instructions.

SAFETY PRECAUTIONS

• Products could probably be damaged due to electrostatic discharge(ESD). Please follow the steps below for a successful computer assembly.
• Make sure all parts are firmly connected; otherwise, it might lead to the failure of recognizing components or starting the computer.
• In order to prevent products from being damaged by ESD, please make sure to discharge your body static by touching other metal objects before taking the motherboard out of the box.
• Hold the border of the motherboard when taking it out. Do not touch the sensitive parts of the motherboard.
• Please put the motherboard in an anti-static container or on an anti-static pad if not needed.
• Before turning on the computer, make sure all parts inside the case are firmly connected without any loose screws or metal components.
• Do not start the computer before installation is finished, otherwise, it might result in permanent damage to the computer parts or even injury to the user.
• If you need any assistance in the process of installation, please contact our after-sales customer service or reach us at HUANANZHI’s official E-mail: business@huananzhi.com for professional technical support.
• Prior to installation or disassembly, please switch off the power and pull the power cable from the socket.
• Keep the motherboard away from moisture.
• Keep the user manual for future reference.
• Before plugging in the power supply, please make sure the socket provides the corresponding voltage.
• In any of the following situations, please keep the motherboard and power cable in a safe place. Do not put anything on the power cable.
• In the event of any of the following conditions, have the board checked by a service technician: Liquid penetrated into the computer. The motherboard is exposed to moisture. The motherboard does not work even if you follow the instructions in the user manual. Motherboard fell off to the ground and got damaged. Motherboard has clear signs of damage.

PACKING

Please confirm that the motherboard is properly packaged upon purchase of the product. If there is any damage to the packaging or lack of accessories, contact us as soon as possible.

1. 1*HUANANZHI X99-T8 Motherboard
2. 2*SATA data cable
3. 1*1/O shield back plat
4. 1* User manual
5. 1*Warranty card

BRIEF INTRODUCTION

Features

• CPU: Intel® LGA2011-3 Processor Intel® Xeon™ E52678V3/2676V3/2673V3/2629V3/2649V3/2666V3/2669V3/2696V3
• RAM: 8*DIMM supports up to 256GB DDR3 1866/1600/1333MHZ Non-ECC.ECC memory Quad-Channel Memory Architecture Actual memory data rate depends on CPU type and DRAM module
• 1/O effects: 4 x SATA3.0 (maximum transfer speed up to 6GB/5) 4 x SSATA3.0 4 x USB2.0 interface 4 x USB3.0 ports 1 x PS/2 Mouse and Keyboard port 1 x RJ45 Network card interface
• Audio: Realtek Audio Transcoder Realtek 7.1 Surround Sound High Definition Audio Codec Audio output: Front Out/Front Speaker Out, Rear Speaker output, Center/Subwoofer output, Optical audio output Audio input: Microphone input, Audio input
• Ethernet: 1 x Realtek PCle Gigabit LAN Expansion slot: 2 × PCIe 3.0 x16 1 x PCle 3.0×4 2 x PCle 2.0 x1 1 x M.2 NVME PCIe 3.0X4 (key M)2242/2260/2280 1 x M.2 NVME PCle 2.0X4 (key M)2242/2260/2280

MOTHERBOARD IMAGE

Rear I/O Panel

Installation And Settings

NOTICE

please check the motherboard where all pins are marked with the number“ 1” or white bold line are position“ 1”.

• In order to properly place the CPU in the motherboard, the surface of the LGA2011-3 CPU has two pairs of starting points and a golden triangle. The golden triangle indicates Pin1
• Remove the screw from the screw base.
• Remove the screw base.
• Tighten the screw base screwed into the length M.2 module to the M.2 interface distance hole.
• Insert your M.2 module into the M.2 interface at a 30-degree angle.
• Place the screw on the trailing edge notch of your M.2 module and tighten it to the screw base.
• Pull the clips on both ends of the memory slot outward, and the memory strip corresponds to the protruding position of the slot to determine the direction of installation.
• Align the memory module into the slot and press.
• Let the snaps on both.

Memory Installation

1. Use a screwdriver to remove the bezel and screws on the main unit.
2. Need to pick up the card slot of the card slot when installing the graphics card.
3. Insert the graphics card into the card slot of the graphics card.
4. After the installation is in place, the chuck will automatically return to its position.
5. Secure the graphics card to the chassis with screws.
6. Install the power cord.

Graphics Card Installation

Drivers installation

win7/win10
X99-T8LAN Driver| Realtek network card driver installation| win7/win10

Intel Chip Information Installation

Run“ Control Panel – System – Hardware – Device Manager” Click the right mouse button to change the driver’s hardware device and proceed with the installation below：

Option: Property – Update driver – Not connect to the Internet – Manually installation Find the corresponding directory Select “Next step”

Audio driver installation

Before this installation, please check the model of the audio chip on the motherboard first(you may refer to this manual), Select the proper driver accordingly for installation.

Audio driver installation (take the HD Audio series for example)

Run “driver installer”: /X99-T8 Audio/0003-64bit_Win7Win8 Win81 R276.exe Click on “next” to continue, and then”finished” The system will automatically restart itself to finish the installation.

Uninstallation of audio driver(take HD Audio series for example)

Getting into the Windows desktop, choose “setting”/ “control”, and then “add/remove programs”. Later, choose “Realtek High Definition Audio Driver” in the menu and click on “add/remove”so thatthe driver will be automatically removed.

Driver installation of external video card

• Run “driver installer”, take Setup.exe, and click on “next”- “yes” -“next”- next” and“finished”
• The system will automatically search for devices to complete the installation.

Driver installation of network

Run “driver installer*•X99-T8 LAN/Install_ Win7_7126_06242019 /Install_Win10_10035_06242019/setup.exe click on “next”. “installation”. “finished” and restart the computer, and restart the computer, The system will automatically search for devices to complete the installation.

BIOS Settings

In order to enable the computer to work well or execute specific functions, CMOS SETUP normally stores all kinds of data in the CMOS SRAM of the motherboard. When the computer is shut down, the motherboard’s battery will supply power to CMOS SRAM. When the computer is turned on and starts POST(Power On Self Test), press the “ Delete/Del” key to enter into AMI BIOS CMOS SETUP main page. The motherboard warm boot key is“ F7”. Menu: please pay attention to every option in the settings menu. When there is a triangle- shaped symbol on the left side of the menu, it means that you choose this sub- menu, so a pop-up sub-menu will be available.

Main Menu Function

Main Advanced Chipset Boot Security Save Exit

• Main System Overview Date/Time settings, HDD specs/Monitor type settings.
• Advanced Settings BIOS special function settings, such as virus alert, booting disk priority etc.
• Chipset Advanced Chipest Settings
• Boot Boot Settings
• Security Security Settings
• Save Save Setting
• Exit Exit Options Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving.Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving.

WWW.HUANANZHI.COM

References

• 华南金牌官网

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>