i d W EB069 Cool Air Sliding Door Set Running Within The Wall Instruction Manual
- June 11, 2024
- i d W
Table of Contents
Instructions for Fitting
Sliding door set running within the wall
EB069 RE / Stand: 10.2022 / Druck: 10.2022
+
| NL| PL| SL| FI| TR| LV| EL| UK
---|---|---|---|---|---|---|---|---
IT| HU| NO| DA| LT| HR| RO|
PT
| CS| SV| SK| ET| SR|
BG
|
Dissemination as well as duplication of this document and the use and
communication of its content are prohibited unless explicitly permitted.
Noncompliance will result in damage compensation obligations. All rights
reserved in the event of patent, utility model or design model registration.
Subject to changes.
Dear Customer,
We are delighted that you have chosen a quality product from our company.
1 About these instructions
Read through all of the instructions carefully: they contain important
information about the product and fitting.
Pay attention to and follow the instructions provided, particularly the safety
instructions and warnings.
Please keep these instructions in a safe place and make sure that they are available to all users at all times. These instructions are important documentation for the building files.
Expert fitting and careful maintenance increase the performance, availability and security.
1.1 Warnings used
The general warning symbol indicates a danger that can lead to injury or death. In the text section, the general warning symbol will be used in connection with the caution levels described below. In the illustrated section, an additional instruction refers back to the explanation in the text.
ATTENTION
Indicates a danger that can lead to damage or destruction of the
product.
1.2 Symbols used
Important advice to
prevent injury to persons and damage to property
Correct arrangement or
activity
Non-permissible
arrangement or activity
Protection against
weather
Indicates steps in the
illustrated section that must be performed in sequence.
Inspect
Tighten the screws
firmly
See text section
Optional
1.3 Abbreviations used
OFF Finished floor level
mm All dimensions in the illustrated section are in mm
2 Basic principles
2.1 Sliding door set running within the wall
1
| Offset lintel
---|---
2
| Continuous lintel, with track cover
3
| Reveal lining for glass doors
2.2 Foaming the sliding door frame
We recommend a 2 component PUR fitting foam for foaming. Suitability should be proven in accordance with the ift guideline. Note the safety instructions as well as the notes on use from the fitting foam manufacturer.
ATTENTION
Foaming the sliding door frame
▶ Ensure a solid, clean subsurface free of grease.
If necessary, use a primer.
▶ Always use at least 3 foam points per frame side, top, centre, bottom. Foam
along the entire frame width / wall thickness.
▶ Also always foam the upper frame corners.
▶ In case of single-leaf sliding doors running within the wall, door width >
1000 mm, additional mechanical connections are required between the frame
crosspiece and the wall lintel.
3 Fitting
3.1 Sliding door set running within the wall
Check that the individual frame parts are free of faults and complete, check the dimensions and check that screws are tight before assembling the frame.
– Frame parts (4 ×)
a. Fitting side with groove (2 ×)
b. Inlet side without groove (2 ×), if necessary (4 ×)
– Frame part headers (2 ×)
– Decorative edges to suit frame parts
– Fittings bag
– Intermediate part (for a single-leaf door set)
– Sliding door rail (if not already delivered and fitted)
respectively confirmed and packaged separately.
A possible, larger, design-related opening between door leaf top edge and frame can be covered by fitting a cover strip in the lintel area of the two frame halves.
NOTE
Processed goods cannot be exchanged.
3.2 Checking fitting situation
– Suitability of the wall type
– Finished level / metre line of the floor
– Door opening sense
– Sliding door rail position
Observe building regulations
4 Fitting by qualified personnel and warranty
The supplied products may only be fitted and put into operation by qualified personnel. We do not provide any warranty, as fitting is outside of our sphere of influence. These fitting instructions only provide recommendations, as there are several possibilities for professional and correct fitting. No legal claims can be derived from recommendations.
Putting the door into operation is prohibited until it has been established that the door has been installed in accordance with our specifications and its function has been properly tested. A product’s declaration of performance becomes invalid if an alteration to the product is carried out without consultation with us.
Wood is a natural product with individual characteristics and nuances. It reacts to changes in air humidity, amongst others. The door and frame should be subjected to as few fluctuations in humidity as possible. We therefore advise against fitting in rooms with more than 60% relative air humidity (take note of humidity in new buildings).
5 Care and maintenance
A slightly damp cloth, chamois or a lint-free microfibre cloth without using special detergents is enough to maintain the high-quality surfaces of doors and frames. This allows normal household dirt (e.g. fingerprints or water splashes) to be easily removed. Use lukewarm water with a squirt of washing-up liquid for stubborn dirt. Then dry off well. Do not use any abrasive or caustic solvent-based detergents!
All important functional parts must be visually inspected on a regular basis (min. 1 × annually) for fastening and function. Identified defects (e.g. loose screws, damaged or missing seals, incorrectly set or stiff hinges) must be promptly addressed.
Please ask your dealer for further processing, maintenance and care instructions and for certificates and verifications.
EB069 RE / 10.2022
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>