HUANANZHI X99-F8D Plus Motherboard User Manual

June 11, 2024
HUANANZHI

HUANANZHI X99-F8D Plus Motherboard User Manual

SAFETY PRECAUTIONS

  • Products could probably be damaged due to electrostatic discharge(ESD). Please follow these steps below for a successful computer assembly.
  • Make sure all parts are firmly connected; otherwise, it might lead to the failure of recognizing components or starting the computer.
  • In order to prevent products from being damaged by ESD, please make sure to discharge your body static by touching other metal objects before taking the motherboard out of box.
  • Hold the border of motherboard when taking it out. Do not touch the sensitive parts of motherboard.
  • Please put the motherboard in an anti-static container or on anti-static pad if not needed.
  • Before turning on the computer, make sure all parts inside the case are firmly connected without any loose screws or metal components.
  • Do not start the computer before installation finished, otherwise it might result in permanent damage to the computer parts or even injury to the user.  1 DIRECTORY SAFETY PRECAUTIONS 02
  • If you need any assistance in the process of installation,please contact our after-sales customer service or reach us on HUANANZHI official E-mail:bussiness@huananzhi.com for professional technical support.
  • Prior to installation or disassembly, please switch off the power and pull the power cable from the socket.
  • Keep the motherboard away from moisture.
  • Keep the user manual for future reference.
  • Before plugging the power supply, please make sure the socket provides the corresponding voltage.
  • In the event of any of the following conditions, have the board checked by a service technician:

Liquid penetrated into the computer.
Motherboard is exposed to moisture.

Motherboard does not work even if you follow the instructions on user manual.

Motherboard fell off to the ground and got damaged.
Motherboard has clear signs of damage.

PACKING

Please confirm that the motherboard is properly packaged upon purchase of the product. If there is any damage to packaging or lack of accessories, contact us as soon as possible.

  1. HUANANZHI X99-F8D DUAL motherboard
  2. SATA data cable
  3. I/O shield back plat
  4. User Manual
  5. Warranty Card

BRIEF INTRODUCTION

Features

CPU : Intel® LGA2011-3 Processor Intel® Xeon™

RAM : 8*DIMM supports up to 256GB DDR4 2400/2133/1866MHZ Non-ECC.ECC memory

Quad-Channel Memory Architecture

Actual memory data rate depends on CPU type and DRAM module

I/O effects: 6 x SATA 3.0 (maximum transfer speed up to 6GB/s)

  • 4 x SSATA3.0
  • 4 x USB2.0 interface
  • 4 x USB3.0 interface
  • 1 x RTL8125BG Network card interface

Audio: Realtek Audio Transcoder

  • Realtek 7.1 Surround Sound High Definition Audio Codec
  • Audio output:Front Out/Front Speaker Out,Rear Speaker output,
  • Center/Subwoofer output,Side Hom output
  • Audio input:Microphone input,Audio input

Ethernet: 2 x Realtek PCle Gigabit LAN
Expansion slot: 3 x PCIe 3.0 x16

  • 2 x M.2 22110 NVME PCIe 3.0X4
  • 1 x M.2 2280 NVME PCIe 2.0 X4@NGFF SSATA3.0

MOTHERBOARD DIAGRAM

MOTHERBOARD DIAGRAM

  1. X99-F8D PLUS motherboard illustration

Rear I/O Panel

MOTHERBOARD DIAGRAM

Overall Rear I/O Panel Display
Panel Display

LAN Port Status Table
Table

Installation And Settings

NOTICE

please check the motherboard where all pins marked with number “1” or white bold line are position “1”.

Clear CMOS Jumper CLR-CMOS
Installation And Settings

Front  Audio Output Ports


1| MIC+
2| Ground
3| Vbias
4| AuD_Vcc(AVCC)
5| L_R_Out
6| R_Out Bac
7| N.C
8| KEY
9| L_L_Out
10| L_Out Back

USB Extension Interface


1| VCC
2| VCC
3| D
4| D
5| D+
6| D+
7| GND
8| GND
9| N.C
10| KEY

Installation And Settings

PCI Expansion Slot


1| PWR LED+
2| HDD LED+
3| PWR LED-
4| HDD LED
5| PWR_SW
6| RESET_SW
7| PWR_SW
8| RESET_SW
9| PWR_SW KEY
10| N.C

F_PANEL1 Boot Interface


1| Power
2| USB3_RX
3| USB3_RX_DP
4| Ground
5| USB3_TX_C_DN
6| USB3_TX_C_DP
7| Ground
8| USB2.0-
9| USB2.0+
10| GND
11| USB2.0+
12| USB2.0-
13| Ground
14| USB3_TX_C_DP
15| USB3_TX_C_D
16| Ground
17| USB3_RX_DP
18| USB3_RX_DN
19| Power
20| N.C

Instructions

  • In order to properly place the CPU in the motherboard, the surface of the LGA2011-3 CPU has two pairs of starting points and a golden triangle. Golden triangle indicates Pin1

CPU Installation

  1. Remove the screw from the screw base

  2. Remove the screw base

  3. Tighten the screw base screwed into the length M.2 module to the M.2 interface distance hole

  4. Insert your M.2 module into the M.2 interface at a 30 degree angle
    CPU Installation

  5. Place the screw on the trailing edge notch of your M.2 module and tighten to the screw base.

Interface Installation

Memory Installation

  1. Pull the clips on both ends of the memory slot outward, and the memory strip corresponds to the protruding position of the slot to determine the direction of installation.

  2. Align the memory module into the slot and press

  3. Let the snaps on both ends of the slot automatically bounce

M.2 Interface Installation

  1. Remove the screw from the screw base

  2. Remove the screw base

  3. Tighten the screw base screwed into the length M.2 module to the M.2 interface distance hole

  4. Insert your M.2 module into the M.2 interface at a 30 degree angle
    CPU Installation

  5. Place the screw on the trailing edge notch of your M.2 module and tighten to the screw base

Graphics Card Installation

  1. Use a screwdriver to remove the bezel and screws on the main unit

  2. Need to pick up the card slot of the card slot when installing the graphics card

  3. Insert the graphics card into the card slot of the graphics car

  4. After the installation is in place, the chuck will automatically return to its position.

  5. Secure the graphics card to the chassis with screws

  6. Install the power cord
    Card Installation

SATA Interface
SATA Interface

Drivers installation

Drivers listing:

Driver Directory Driver Description Operating System
X99-F8D PLUS Chipset Driver Intel chip
information installation win7/win10/win11
X99-F8D PLUS Suond Card Driver Realtek series sound card
driver installation win7/win10/win11
X99-F8D PLUS LAN Driver Realtek network card
driver installation win7/win10/win11

Intel Chip Information Installation

Run “Control Panel – System – Hardware – Device Manager” Click the right mouse button to change the driver’s hardware device and proceed with the installation below:

Option: Propertyl – Update driverl – Not connect to Internet – Manually installation Find the corresponding directory Select “Next step”

Audio driver installation
Before this installation, please check the model of the audio chip on the motherboard first(you may refer to this manual), Select the proper driver accordingly for installation.

Audio driver installation (take HD Audio series for example)
Run “driver installer”: /X99-F8D PLUS SOUND CARD DRIVER /VISTA-WIN7-R267, take WDW-267 if OS is XP Click on “next”to continue,and then”finished” The system will automatically restart itself to finish the installation

Uninstallation of audio driver(take HD Audio series for example)
etting into Windows desktop, choose “setting”/ “control”,and then “add/remove programs”. Later, choose “Realtek High Definition Audio Driver” in the menu and click on “add/remove”so thatthe driver will be automatically removed.

Driver installation of external video card
Run “driver installer”, take Setup.exe, Click on “next”- “yes” -“next”-“next”and”finished”h The system will automatically search for devices to complete the installation

Driver installation of network
Run “driver installer”: X99-F8D LAN DRIVER/WIN7 XP click on “next”- “installation”- “finished”and restart the computer, and restart the computer,The system will automatically search for devices to complete the installation.

BIOS Settings

In order to enable the computer to work well or execute specific functions, CMOS SETUP normally stores all kinds of data in CMOS SRAM of the motherboard. When the computer is shut down, motherboard’s battery will supply power to CMOS SRAM. When the computer is turned on and starts POST(Power On Self Test), press “Delete/Del” key to enter into AMI BIOS CMOS SETUP main page. Motherboard warm boot key is “F11”,Save the key “F10” 13 BIOS Settings Menu: please pay attention to every option in the settings menu. When there is a triangle shaped symbol on the left side of menu, it means that you choose this sub-menu,so a pop-up sub-menu will be available

Main Menu Function

  • Main
  • System Overview Date/Time settings, HDD specs/Monitor type settings.
  • Advanced Advanced Settings BIOS special function settings, such as virus alert, booting disk priority etc. Main Advanced Chipset Boot Security Save Exit BIOS Settings 14
  • Chipest
  • Boot Boot Settings
  • Security Security Settings
  • Save Save Setting
  • Exit Exit Options

Exit settings include loading of optimized defaults value/ loading of fail- safe defaults / discarding changes/ exiting without saving.Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals