HYUNDAI 21FOM Series 21 Inch Monitor User Manual

HYUNDAI 21″ MONITOR
21FOM Series
USER MANUAL

WARRANTY NOTICE

Limited Warranty does NOT cover:
Any costs associated with the repair or replacement of the Product including labor, installation or other costs incurred by you, and in particular, any costs relating to the removal or replacement of any Product that is soldered or otherwise permanently affixed to any printed circuit board; OR Damage to the Product due to external causes, including accident, problems with electrical power, abnormal electrical, mechanical or environmental conditions, usage not in accordance with product instructions, misuse, neglect, alteration, repair, improper installation, or improper testing; OR Any Product which has been modified or operated outside of specifications or where the original identification markings (trademark or serial number) has been removed, altered or obliterated from the Product, or where the label or screw on the exterior of the Product is removed or broken.

Important Safety Instructions

Read these instructions thoroughly and keep this user manual for future use.
Do not use the product near water. Never spill liquid of any kind of the products.
Clean LCD monitor when power off. Never clean it with liquid cleaness or liquefier. Better use clean wet cloth carefully.
Do not place the product on an unstable cart, stand or table. Doing so may cause the product to fall, which can seriously damage it.
To ensure reliable operation, never block these ventilation slots by placing the product on a bed, rug or similar surface; this product should never be placed near or over a radiator or heat register; or installed in any enclosure that prevents proper ventilation.
Do not place any object on the adapter. Do not place this product where persons could walk on the adapter.
Never push objects of any kind through the ventilation slots at the back of the product. To do so could risk fire or electronic shock.
Do not attempt to service this product by yourself. Opening or removing covers may expose you to dangerous voltage that could cause fire or electronic shock.
Refer all servicing needs to authorized service personnel.
Unplug this product from the wall outlet and contact authorized service personnel under the followin conditions:
a. When the adapter or plug is damaged or frayed.
b. If a liquid has been spilled into or on the product.
c. lf the product has been rained or spilled by water.
d. If the product has been dropped or the cabinet has been damaged.
e. If the product does not operate normally when operating instructions are followed, and product shows to be maintained.

Special Notice:
Only under normal condition can the quality of LCD products be assured during operation. Normal condition as following:
Temperature: 20±15;
Moisture: 65±20;
Display image: continuously changing image. (Not freezing image).
For the LCD products, the phenomenon of image stagnation may appear when display the freezing image for a certain long time. All the display products including LCD may have this kind of image stagnation, and this is not a kind of defect.
In order to avoid the phenomenon of image stagnation, we suggest that the screen protection program be set when your PC or system is spare.

Connection

1. Turn Off computer and Unplug Adapter.
2. To connect signal cable with 15pin into VGA or HDMI out hole on the back of monitor, and to be sure to tighten switches on both ends of signal cable.
3. To plug PC and monitor adapter to the nearest socket.
4. Turn on PC and monitor, image possibility shows successful installation. If not, please double check all the connections.

Notes:

1. To connect signal cable and plug adapter to be assure monitor safety on process of installation.
2. To avoid monitor damaged, please handle the centre part of front cover while it installation.

Monitor Input Connections

1. DC
   Power Input

2. HDMI
   Signal Input

3. VGA
   Signal Input

Stand Assembly Instruction

Front Panel Controls

1. Press it to open the OSD MENU, to select MENU options when the OSD MENU is displayed.
   Hot key to adjust contrast.
   ◄ Down selection button.
   Hot key to adjust brightness.
   ► Up selection button.

2. Hot key to automatically optimize positions, phase and clock when OSD is not shown.
   To exit OSD MENU when OSD is shown.
   **** Power On or OFF; LED-On Normal; LED flicker: Power Saving; LED-Off: Power Off.

Power Switch.
Press this button to turn on or off the monitor. Note: It will not cut off power supply. But to unplug pin from the socket.
Power Indicator.
LED Power Indicator
LED-On: Normal;
LED flicker: Power Saving;
LED-Off: Power Off.

Operate Explanation.
Your LCD has been adjusted to ¡ts optimal status before shipment. You can also adjust the image in accordance with the following allustrations and steps.

• Press the “1” button to start the OSD feature.
• Click the “ ► ” or “ ◄ ” to select the function to be adjusted.
• Click the “1” button to access into the function to be adjusted.
• Click “ ► ” or ” ◄  ” button to change the current setting of the function.
• To exit OSD MENU or go back to the previous action by “2”.
• To repeat above steps for changing the setting of the other function.

OSD Control.

• CONTRAST: Press ” ◄ ” adjust the Contrast.
• BRIGHTNESS: Press ” ◄ ” adjust the Brightness.
• AUTO: Phase and clock when OSD is not shown.

MENU.

Brightness
Color
Temperature
Auto Adjust
Auto Color| AdJust the contrast of the Image.
Adjust the brighiness of the screen.
Set up the color Temp. to be 9300K 8500K  5500K USER red,
green, blue to adjust red / green / blue.
Set up to adjust clock, phase and position automatically.
Adjust the color of the screen.
Picture| H. Position
V. Position
Clock
Phase| Move the Image left and right on the screen.
Move the Image up and down on the screen.
AdJust the clock pulse of the image.
Adjust the focus of image.
OSD Menu| Languaje
OSD H. Pos.
OSD V. Pos.
OSD Timer
Transparency|
Select the language you want.
Move the OSD left and right on the screen.
Move the OSD up and down on the screen.
Adjust OSD display time setting.
Adjust OSD Transparency.
Others| MODE
Aspect Ratio
DCR MODE| Select PC / GAME / MOVIE display mode.
Select the display mode: 16:9 / AUTO / 4:3
Select the DCR Mode On or Off (optional).
Reset| NONE| Restore to factory settings.

Specification

Display Mode

Display Mode| Hor. Sync (kHz)| Vert. Sync (Hz)| Pixel Clock (MHz)| Sync. Polarity (H/V)
---|---|---|---|---
VGA 640×480| 31.469
37.861
37.500| 59.940
72.809
75.000| 25.175
31.500
31.500| -/-
-/-
-/-
SVGA 800×600| 35.156
37.879
48.077
46.875| 56.250
60.317
72.188
75.000| 36.000
40.000
50.000
49.500| +/+
+/+
+/+
+/+
XGA 1024×768| 48.363
56.476
60.023| 60.004
70.069
75.029| 65.000
75.000
78.750| -/-
-/-
+/+
SXGA 1280×1024| 63.981
79.976| 60.020
75.025| 108.000
135.000| +/+
+/+
WXGA 1440×900
WSXGA 1680×1050
WSXGA 1920×1080| 55.9
65.29
67.2| 59.8
59.954
60.1| 106.00
146.25
172| -/+
-/+
-/+

HYUNDAI
Google is a trademark of Google LLC.
The information contained herein is subject to change without notice. The only warranties for Connect and services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty. Hyundai Technology shall not be liable for technical or editorial errors or omissions contained herein.
First Edition: May 2022

Contact Us
Visit us at http://www.hyundaitechnology.com/
For sales inqury (U.S. Worldwide)
Email [email protected]
For technical support please contact HYUNDAI®
U.S. and Worldwide
Toll Free Number: 800-560-0626
Monday-Friday 8:00am-5:00pm PST
Email: [email protected]
México (Spanish)
Toll Free Number: 81 5030-7375
Lunes-Viernes 8:00am-5:00pm CST
Email: [email protected]

References

• Computers, laptops, tablets and smart home solutions – Hyundai Technology

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>