HUANANZHI H510-D4 Motherboard User Manual

HUANANZHI H510-D4 Motherboard

Product Information: H510-D4 Motherboard

The H510-D4 is a motherboard designed for use with Intel LGA1200 CPUs. It supports ECC and XMP CPU and DRAM, with a maximum memory
frequency of 2933/2666/2400MHZ. The board features 4x SATA3.0 (6GB/s) ports, 4x USB2.0 ports, 2x USB3.0 ports, 1x PS/2 port, 1x RJ45 port, 1x VGA port, 1x HDMI port, and 1x DP port. It also includes a Realtek LAN controller, Realtek audio codec, and a PCIe 3.0 x16 slot, a PCIe 3.0 x1 slot, and an M.2 NVME PCIe 3.0X4 slot (key M)2242/2260/2280.

Product Usage Instructions

1. Ensure all parts are firmly connected before starting the computer to avoid failure in recognizing components or starting the computer.
2. Discharge your body static by touching other metal objects before taking the motherboard out of the box to prevent products from being damaged by ESD.
3. Install the H510-D4 chipset driver for Intel win7/win10/win11 and the sound card driver.
4. Install the LAN driver for Realtek win7/win10/win11.
5. Access BIOS settings by pressing Delete during BIOSPOST (Power On Self Test) or F7 during CMOS SETUP.
6. Refer to the motherboard diagram and rear I/O panel for proper installation and settings.
7. For overclocking, access BIOS settings and adjust accordingly.

SAFETY PRECAUTIONS

• Products could probably be damaged due to electrostatic discharge(ESD). Please follow these steps below for a success-ful computer assembly.

• Make sure all parts are firmly connected; otherwise, it might lead to the failure of recognizing components or starting the computer.

• In order to prevent products from being damaged by ESD, please make sure to discharge your body static by touching other metal objects before taking the motherboard out of box.

• Hold the border of motherboard when taking it out. Do not touch the sensitive parts of motherboard.

• Please put the motherboard in an anti-static container or on anti-static pad if not needed.

• Before turning on the computer, make sure all parts inside the case are firmly connected without any loose screws or metal components.

• Do not start the computer before installation finished, otherwise it might result in permanent damage to the computer parts or even injury to the user.

• If you need any assistance in the process of installation, please contact our after-sales customer service or contact us on Huananzhi official mail:huananzhi@yeah.net or Huananzhi official Wechat:nick515 for professional technical support.
  Prior to installation or disassembly, please switch off the power and pull the power cable from the socket.

• Keep the motherboard away from moisture.

• Keep the user manual for future reference.

• Before plugging the power supply, please make sure the socket provides the corresponding voltage.

• In any of the following situations, please keep the motherboard and power cable in a safe place. Do not put anything onto the power cable.

• In the event of any of the following conditions, have the board checked by a service technician:

  • Liquid penetrated into the computer.
  • Motherboard is exposed to moisture.

• Motherboard does not work even if you follow the instructions on user manual.

• Motherboard fell off to the ground and got damaged.

• Motherboard has clear signs of damage.

PACKING
Please confirm that the motherboard is properly packaged upon purchase of the product. If there is any damage to packaging or lack of accessories, contact us as soon as possible.

1. HUANANZHI H510-D4 motherboard
2. SATA data cable
3. User manual
4.  Warranty card

BRIEF INTRODUCTION

Features

CPU : Intel ® 10TH11THLGA1200 Processor I9/I7/I5/I3 Intel ® Croe™ RAM： 2*DIMM supports up to 64GB DDR4 2933/2666/2400MHZ Non EC Cmemory(Depends on CPU / supports XMP) Dual channel storage architecture
Actual memory data rate depends on CPU type and DRAM module
I/O effects： 4 x SATA3.0 (maximum transfer speed up to 6GB/s)

• 4 x USB2.0 interface
• 2 x USB3.0 ports
• 1 x PS/2 Mouse and Keyboard port 1 x RJ45 Network card interface 1 x VGA
• 1 x HDMI-Compatible
• 1 x DP

Audio: Realtek Audio Transcoder

Realtek High Definition Audio
Audio output: Front Out/Front Speaker Out Audio input: Microphone input Audio input.
Ethernet: 1 x Realtek Pickle Gigabit LAN Expansion slot：

• 1 x PCIe 3.0 x16
• 1 x PCIe 3.0 x1
• 1 x M.2 NVME PCIe 3.0X4 (key M)2242/2260/2280

THE MOTHERBOARD DIAGRAM

1-1 H510-D4 Motherboard Illustration

Rear I/O Panel

1-2 Overall Rear I/O Panel Display

1-3 LAN Port Status Table

1-4 Audio Port Configuration

Installation And Settings

NOTICE
please check the motherboard where all pins marked with number “1” or white bold line are position “1”.

2-1 Clear CMOS Jumper CLR-CMOS

2-5 F_PANEL1 Ports

2-3 USB Expansion Ports

2-4 PCI-E Expansion Slot

2-5 F_PANEL1 Ports

2-6 USB 3.0 Interface

Figure 2-6 CPU installation

• To place the CPU properly on the motherboard, the SURFACE of the LGA1200 CPU has two pairs of starting points and a golden trian-gle. The golden triangle indicates Pin1.

1. Remove the screw from the screw base

2.  Remove the screw base

3. Tighten the screw base screwed into the length M.2 module to the M.2 interface distance hole

4. Insert your M.2 module into the M.2 interface at a 30 degree angle
   

5. Place the screw on the trailing edge notch of your M.2 module and tighten to the screw base
   

2-7 M.2 Interface Installation

1. Pull the clips at both ends of the memory slot outwards, and the memory strip corresponds to the protruding position of the slot to determine the direction of installation
2. Align the memory strip to the slot and press down
3. Make the clips on both ends of the slot spring up automatically

2- 8 Memory Installation

1. Use a screwdriver to remove the bezel and screws on the main unit

2. Need to pick up the card slot of the card slot when installing the graphics card
   

3. Insert the graphics card into the card slot of the graphics card

4. After the installation is in place, the chuck will automatically return to its position.
   

5. Secure the graphics card to the chassis with screws 6.Install the power cord

2-9 Graphics Card Installation

2-10 SATA Interface

Drivers Installation

Drivers listing

win7/win10/win11
H510-D4 LAN Driver| Rdreiavletrekinnsteatlwlaotriokncard| win7/win10/win11

• Run “driver installer” :Intel_ChipsetDriver
• V10_1_18838_8284_WIN10_Win11_64_bit.exe
• Select “Next” to continue
• Select “Finish” and restart the computer. The system will automatically find the devices. Installation finished.
• Run“ Control Panel – System – Hardware – Device Manager”
• Click the right mouse button to change the driver’s hardware device and proceed with the installation below：
• Option: Propertyl – Update driverl – Not connect to Internet –
• Manually installation
• Find the corresponding directory
• Select “Next step

Audio driver installation
Before this installation, please check the model of the audio chip on the motherboard first(you may refer to this manual), Select the proper driver accordingly for installation.

Audio driver installation (take HD Audio series for example)

Run “driver installer”:audio_realtek_6.0.9191.1_x64/Setup.exe, take Click on “next” to continue, and then “finished” The system will automatically restart itself to finish the installation.

Driver installation of external video card

Getting into Windows desk top, choose “setting”/ “control”, and then “add/remove programs”. Later, choose “Realtek High Definition Audio Driver” in the menu and click on “add/remove” so that the driver will be automatically removed.

Driver installation of external video card

• Run “driver installer”, take Setup.exe,
• click on “next”- “yes” “next”and”finished”
• The system will automatically search for devices to complete the installation

Driver installation of network
Run “driver installer”: Realtek Install Win10_10051_09282021.exe click on “next”-“installation”-” finished” and restart the computer the system will automatically search for devices to complete the installation.

BIOS Settings

In order to enable the computer to work well or execute specific functions, CMOS SETUP normally stores all kinds of data in CMOS SRAM of the motherboard. When the computer is shut down, motherboard’s battery will supply power to CMOS SRAM. When the computer is turned on and starts POST(Power On Self Test), press“ Delete/Del” key to enter into AMI BIOS CMOS SETUP main page. Motherboard warm boot key is“ F7”
Menu: please pay attention to every option in the settings menu. When there is a triangle shaped symbol on the left side of menu, it means that you choose this sub menu, so a pop-up sub-menu will be available.

Main Menu Function

• Main
• System Overview
• Date/Time settings, HDD specs/Monitor type settings.
• Advanced
  • Advanced Settings BIOS special function settings, such as virus alert, booting disk priority etc.
  • Overlocking Memory XMP overlocking function setting
• Chipest Advanced Chipest Settings
• Boot
  • Boot Settings
• Security
  • Security Settings
• Save & Exit
  • Save Setting & Exit Options
  • Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving. Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>