HUANANZHI H81 Motherboard User Manual

HUANANZHI H81 Motherboard

Product Information

The H81 motherboard is produced by SZ Huanan Sanxian Technology Co., Ltd. and can be found on their website, www.huananzhi.com. It supports up to 16GB DDR3 1600/1333-1066MHZ Non-ECC memory with a Two-Channel Memory Architecture. The motherboard has 2 x SATA3.0 and 2 x SATA2.0 ports with maximum transfer speeds up to 6GB/s and 2GB/s respectively. It also has 2 x USB3.0 interfaces, 4 x USB2.0 ports, 1 x PS/2 Mouse and Keyboard port, 1 x RJ45 Network card interface, and 1 x DVI, 1 x HDMI-Compatible, and 1 x VGA video output ports.

Product Usage Instructions

• Before assembling the computer, follow the safety precautions to prevent electrostatic discharge (ESD) damage to the product. Make sure all parts are firmly connected to avoid failure in recognizing components or starting the computer. Discharge your body static by touching other metal objects before taking the motherboard out of the box to prevent ESD damage.
• Prior to installation or disassembly, switch off the power and pull the power cable from the socket.
• Confirm that the motherboard is properly packaged upon purchase of the product. If there is any damage to packaging or lack of accessories, contact the manufacturer as soon as possible.
• Refer to the directory for brief introduction, features, and packing details of the product.
• For BIOS setup, access the CMOS SETUP through BIOSPOST (Power On Self Test) by pressing the Delete key (for AMI BIOS) or F7 key. The BIOS has Main, Advanced, Chipset, Boot, Security, Save, and Exit options. Use these options to navigate through the BIOS settings and save changes.
• For driver installation, install the H81 chipset driver, Intel driver, Realtek sound card driver, and H81 LAN driver for Windows 7 or Windows 10. Refer to the user manual for instructions on driver installation.

SAFETY PRECAUTIONS

• Products could probably be damaged due to electrostatic discharge(ESD). Please follow these steps below for a successful computer assembly.
• Make sure all parts are firmly connected; otherwise, it might lead to the failure of recognizing components or starting the computer.
• In order to prevent products from being damaged by ESD, please make sure to discharge your body static by touching other metal objects before taking the motherboard out of box.
• Hold the border of motherboard when taking it out. Do not touch the sensitive parts of motherboard.
• Please put the motherboard in an anti-static container or on anti-static pad if not needed.
• Before turning on the computer, make sure all parts inside the case are firmly connected without any loose screws or metal components.
• Do not start the computer before installation finished, otherwise it might result in permanent damage to the computer parts or even injury to the user.
• If you need any assistance in the process of installation, please contact our after-sales customer service or reach us on HUANANZHI official E-mail: bussiness@huananzhi.com for professional technical support.
• Prior to installation or disassembly, please switch off the power and pull the power cable from the socket.
• Keep the motherboard away from moisture.
• Keep the user manual for future reference.
• Before plugging the power supply, please make sure the socket provides the corresponding voltage.
• In any of the following situations, please keep the motherboard and power cable in a safe place. Do not put anything onto the power cable.
• In the event of any of the following conditions, have the board checked by a service technician:
  • Liquid penetrated into the computer.
  • Motherboard is exposed to moisture.
  • Motherboard does not work even if you follow the instructions on user manual.
  • Motherboard fell off to the ground and got damaged.
  • Motherboard has clear signs of damage.

PACKING

Please confirm that the motherboard is properly packaged upon purchase of the product. If there is any damage to packaging or lack of accessories, contact us as soon as possible.

1. HUANANZHI H81 Motherboard
2. SATA Data Cable
3. I/O Shield Back Plat
4. User Manual
5. Warranty Card

BRIEF INTRODUCTION

Features

• CPU:
  • Intel ® LGA1150 I3/I5/I7 4th Generation Intel ® Core ™
  • Intel ® LGA1150 4th Generation Intel ® Celeron ™
  • Intel ® LGA1150 4th Generation Intel ® Pentium ™
• RAM:
  • 2*DIMM supports up to 16GB DDR3 1600/1333-1066MHZ Non-ECCmemory
  • Two-Channel Memory Architecture
  • Actual memory data rate depends on CPU type and DRAM module
• I/O effects:
  • 2 x SATA3.0 (maximum transfer speed up to 6GB/s)
  • 2 x SATA2.0 (maximum transfer speed up to 2GB/s) 2 x USB3.0 interface
  • 4 x USB2.0 ports
  • 1 x PS/2 Mouse and Keyboard port
  • 1 x RJ45 Network card interfacet
  • 1 x DVI
  • 1 x HDMI-Compatible
  • 1 x VGA
• Audio:
  • Realtek Audio Transcoder
  • Realtek 5.1 Channel High Fidelity Audio
  • Audio output: Front Out/Front Speaker Out
  • Audio input: Microphone input, Audio input
• Ethernet:
  • 1 x Realtek 100MB/S Ethernet
• Expansion slot:
  • 1 x PCIe 3.0 x16
  • 1 x PCIe x1
  • 1 x M.2 NVME PCIe 2.0X4 (key M)2242/2260/2280

THE MOTHERBOARD DIAGRAM

Rear I/O panel

Installation And Settings

NOTICE please check the motherboard where all pins marked with number “1” or white bold line are position “1”.

To place the CPU properly on the motherboard, the SURFACE of the LGA1150 CPU has two pairs of starting points and a golden trian-gle. The golden triangle indicates Pin1.

CPU installation

1. Remove the screw from the screw base.
2. Remove the screw base.
3. Tighten the screw base screwed into the length M.2 module to the M.2 interface distance hole.
4. Insert your M.2 module into the M.2 interface at a 30 degree angle.
5. Place the screw on the trailing edge notch of your M.2 module and tighten to the screw base.

M.2 Interface Installation

1. Pull the clips at both ends of the memory slot outwards, and the memory strip corresponds to the protruding position of the slot to determine the direction of installation.
2. Align the memory strip to the slot and press down.
3. Make the clips on both ends of the slot spring up automatically.

2- 8 Memory Installation

1. Use a screwdriver to remove the bezel and screws on the main unit.
2. Need to pick up the card slot of the card slot when installing the graphics card.
3. Insert the graphics card into the card slot of the graphics card.
4. After the installation is in place, the chuck will automatically return to its position.
5. Secure the graphics card to the chassis with screws.
6. Install the power cord.

Drivers installation

Intel Chip Information Installation
Run “Control Panel – System – Hardware – Device Manager” Click the right mouse button to change the driver’s hardware device and proceed with the installation below:
Option: Property – Update driver – Not connect to the Internet – Manually installation Find the corresponding directory Select “Next step”

Audio driver installation
Before this installation, please check the model of the audio chip on the motherboard first(you may refer to this manual), Select the proper driver accordingly for installation.

1. Audio driver installation (take HD Audio series for example)
   • Run “driver installer”: /H81Audio/Realtek_Audio_XP_Win7_8/setup.exe
   • Click on “next” to continue, and then”finished”
   • The system will automatically restart itself to finish the installation
2. Driver installation of external video card
   Getting into Windows desktop, choose “setting”/ “con-trol”,and then “add/remove programs”. Later, choose “Re-altek High Definition Audio Driver” in the menu and click on “add/remove”so that the driver will be automatically removed.

Driver installation of external video card

• Run “driver installer”, take Setup.exe, click on “next”- “yes”
• -“next”
• -“next”and”finished”

The system will automatically search for devices to complete the installation

Driver installation of network
Run “driver installer” H81 LAN/RTL810x_8111_win7/setup.exe click on “next”-“installation”-“finished” and restart the comput-er，the system will automatically search for devices to complete the installation.

BIOS Settings

In order to enable the computer to work well or execute specific functions, CMOS SETUP normally stores all kinds of data in CMOS SRAM of the motherboard. When the computer is shut down, motherboard’s battery will supply power to CMOS SRAM. When the computer is turned on and starts POST(Power On Self Test), press “Delete/Del” key to enter into AMI BIOS CMOS SETUP main page. Motherboard warm boot key is “F11”
Menu: please pay attention to every option in the settings menu. When there is a triangle shaped symbol on the left side of menu, it means that you choose this sub-menu,so a pop-up sub-menu will be available.

Main Menu Function

• Main

• System Overview
  Date/Time settings, HDD specs/Monitor type settings.

• Advanced
  Advanced Settings
  BIOS special function settings, such as virus alert, booting disk priority etc.

• Chipest
  Advanced Chipest Settings

• Boot
  Boot Settings

• Security
  Security Settings

• Save
  Save Setting

• Exit
  Exit Options
  Exit settings include loading of optimized defaults value/ loading of fail- safe defaults / discarding changes/ exiting without saving.Exit settings include loading of optimized defaults value/ loading of fail-safe defaults / discarding changes/ exiting without saving.

SZ HUANAN SANXIAN TECHNOLOGY CO.,LTD.
WWW.HUANANZHI.COM

References

• 华南金牌官网

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>