CENTEK CT-1520 Gas Stove Instruction Manual

: June 11, 2024
: CENTEK

Table of Contents

CT-1520 Gas Stove
SAFETY PRECAUTIONS
APPLIANCE DESCRIPTION
SCOPE OF SUPPLY
OPERATION PROCEDURE
MAINTENANCE
SPECIFICATIONS
DISPOSAL
CERTIFICATION DATA, GUARANTEE
MANUFACTURER AND IMPORTER INFORMATION
TROUBLESHOOTING
Documents / Resources

CT-1520
GAS STOVE
INSTRUCTION MANUAL

CT-1520 Gas Stove

DEAR CUSTOMER!
Prior to operating the appliance, please carefully read the present manual which contains important information regarding its proper and safe operation. Take care not to lose the present manual. The manufacturer will not be responsible for any damage resulting from improper use of the appliance or from non-observance of the instructions and provisions of the present manual, as well as from attempts by unskilled persons at repairing the appliance. Should You decide to transfer the appliance to another person, please pass the present manual over along with it.
PURPOSE OF THE APPLIANCE: for food preparation by heating it in metal kitchen utensils.

SAFETY PRECAUTIONS

The cooker should only be connected to gas supply by skilled personnel of a specialized company authorized for the installation and maintenance of gas cookers. The following requirements should be strictly observed in order to avoid situations hazardous for human life and health, as well as premature failures of the appliance:

The use of a gas cooker will generate heat and humidity in the kitchen. The room should be well ventilated: keep the natural ventilation opening unobstructed or provide forced ventilation facilities. In case of prolonged and intensive use of the cooker provisions for additional ventilation should be ensured, e.g. operating a forced ventilation device at a higher archangel capacity.
The location and operation of the gas bottles connected to the cooker should comply with the local safety and gas supply regulations valid in Your region.
The main gas supply valve shall be located in a visible and easily accessible place.
The following is not allowed in order to avoid the risk of fire:
– Using a malfunctioning cooker.
– Installing the cooker in locations with high fire risks (near wooden surfaces and surfaces lined with wallpapers, combustible plastic, etc.).
– Leaving the operating cooker unattended.
– Using the cooker for purposes other than intended (for room heating, drying clothes, etc.).
– Making modifications to the cooker’s design.
– Storing combustible substances, spray cans, paper, rags, etc. near the cooker.
– Letting children access the operating cooker.
The appliance should not be used by physically, sensory or mentally handicapped persons (including children) or by persons without sufficient experience or knowledge, unless such persons are under supervision, or have been instructed on the use of the appliance, by the persons responsible for their safety. Take precautions not to children play with the appliance.
Immediately call the gas repair service to eliminate the gas leak.
The main gas supply valve shall be closed when the cooker is not in use.
Disconnect the gas supply hose from the cooker prior to washing and other maintenance activities.
Regularly (at least once every six months) check condition of the power cable and gas supply hose. If any defects (cracks, traces of melting, loss of elasticity) should be revealed, immediately apply to a repair service for replacement.
Take special precautions when cooking dishes with high fat or oil content. These can easily ignite when overheated.

CAREFUL: accessible surfaces of the appliance can reach high temperature during operation.
Do not touch the hot surfaces.

ATTENTION: Should the smell of gas occur in the room, immediately close the gas bottle valve or the main gas supply valve, close all valves on the cooker, open all windows and do not perform any activities related to the generation of flame or sparks: do not light matches, smoke, turn on electric lights and appliances, etc.! Close all valves and check all gas hose fittings by smearing with soap suds. Bubbles will appear in leaking places. Tighten the clamps at hose attachment points until full disappearance of the bubbles. If you discover a gas leak, close the gas bottle outlet valve immediately.
NOTE: burns are the most frequent accidents related to cookers! These are usually caused by:
– touching hot parts of the cooker;
– spilling boiling liquids;
– tipping over the vessel on the burner.

APPLIANCE DESCRIPTION

Housing; 2) Burner; 3) Control knob; 4) Grille; 5) Enamel coated burner; 6) Forged aluminum burner.

SCOPE OF SUPPLY

Cooker – 1 ps. 2) Replacement burner 0,7 mm – 1 pc. 3) Grille – 1 pc. 4) Forged aluminum burner – 1 pc. 5) Enamel coated burner – 1 pc. ATTENTION: a nozzle with a diameter of 0.56 mm is already installed. The gas supply hose and clamps are not included in the supply!

OPERATION PROCEDURE

PREPARATIONS FOR USE. INSTALLATION
IMPORTANT: the cooker has no exhaust connection for combustion products. For correct and safe operation the cooker should be installed in a well ventilated room in accordance with the requirements of the present manual and the local safety and operational requirements applicable in Your region.

Do not install the cooker on a lacquered surface of kitchen furniture or on surfaces covered with flammable materials (fabric, rubber, paper, etc). Adjacent furniture, curtains, kitchen towels, etc., should be located at s safe distance to avoid ignition.
The cooker should be installed with a minimum gap of 60 mm from the nearest wall. The wall behind the cooker should be lined with fire-resistant material. The minimum distance from the side of the cooker to vertical furniture panels should be (left and right) should be 200 mm. The minimum vertical distance from the cooker to any overhead shelves or cabinets should be 850 mm.

CONNECTION
Before connecting the cooker ensure that the available gas supply system (gas type and pressure) correspond to the cooker’s settings.

Connect the cooker to the gas bottle via a pressure regulator (reducer).
The pressure regulator is not supplied with the cooker and should be purchased separately.
The cooker can be connected via a rigid pipeline or a flexible hose in accordance with the applicable standards.
If the natural gas pressure exceeds the allowable limit (25 mbar), a pressure reducer shall be installed in the supply line to reduce the pressure to the appropriate value.
Prior to connecting the cooker ensure that the control knob is in the zero position.
After making the connections check burner operation. The burner flame should be uniform, without interruptions or gaps.

CONNECTING VIA A FLEXIBLE HOSE
The following requirements should be observed during the installation and connection of the gas cooker:

the hose should be accessible for inspection over the whole length;
the hose shall not be squeezed, sharply bent or exposed to tensile forces;
the hose should be at least 1.5 meters long;
a damaged hose shall be replaced completely, no repairs are allowed.
Do not check fitting tightness or search for leaks with a lit match or any other open flame!

ATTENTION: if the cooker is connected to a building gas supply system that does not comply with the potential equalization requirements a special isolating joint or a dielectric flexible hose should be used for connecting the cooker.

MAINTENANCE

Keep the cooker clean. A clean cooker will last longer and is pleasant to cook with.
Wash the painted surfaces of the cooker with a soft kitchen sponge soaked in warm water with detergent and then wipe with dry cloth. Take particular care when cleaning the control knobs which feature information symbols.
Do not use a steel wool mop or a knife to remove contamination. Soak caked dirt first.
Do not use abrasive powders, as well as acidic and other aggressive chemicals which can damage the cooker’s surfaces and erase the symbols.
– Remove burners for easier cleaning.
Enamel coated burner caps and the grille can be carefully cleaned with a metal brush or a rag with abrasive cleaning powder.
Do not use steam to clean the cooker.

ROOM VENTILATION REQUIREMENTS
Constant supply of oxygen is required to support combustion. Besides, accumulation of noncomputed gases shall be avoided and the combustion products extracted. Special ventilation facilities should be provided for this purpose, the room should be equipped with an exhaust ventilation channel. If there are no ventilation devices or channels in the room where the cooker is operated, or if these are of insufficient capacity, additional ventilation facilities shall be provided in the form of a ventilation opening as per the requirements provided below (a door or window can serve as such an opening, however, the rooms into which they open should have a direct exhaust into an outdoor area and provide for the abovementioned functions of supplying oxygen and extracting combustion products. The air intake capacity should not be less than 2 m3 /h per 1 kW of burner output. Use the table below to facilitate calculation of ventilation opening sizes.

ROOM AREA	VENTILATION OPENING SIZE
under 5 m³	min. 100 cm²
5 m³ to 10 m³	min. 50 cm²
over 10 m³	not required
basement	min. 65 cм²

SPECIFICATIONS

Enamel coated burner and grille.
Forged aluminum burner.
Flame height control.
Replacement burner for natural (pipeline) gas included (2 pcs.).
The cooker, according to settings, may operate on liquefied propane-butane gas (LPBG) at a pressure of 3000 Pa (0,03 bar) or G20 grade natural gas at a pressure of 2000 Pa (0,02 bar).
The readjustment to a different gas type can be performed by maintenance services authorized for gas appliance maintenance.
The readjustment is performed by replacing the burner nozzle sand low-flowrate adjustment screws (LAS) according to the table below.

Burner Type| Liquefied gas (LPN)*
PN= 3000 Pa (0,03 bar)| Natural Gas (620)
PN= 2000 Pa (0,02 bar)
---|---|---
N ,kW
NOM.| N ,kW
NOM.| Nozzle| LAS| N ,kW
NOM.| N ,kW
NOM.| Nozzle| LAS
Medium velocity burner| 1,70| 0,4| 0,56| 33| 1,80| 0,4| 0,7| 44
Maximum gas flow rate of
gas cooker| 121.5 (gab)| 171.25 UN

*LPBG – liquefied propane-butane gas as per GOST 20448-90 (highest combustion heat Hs – 98,4 MJ/m 3 (50,28 MJ/kg)).

The output and and gas flow rate are shown at an ambient temperature of 15 °С and an atmospheric pressure of 101,3 kPa (acc. STB EN 30-1-1-2005). Column “Nozzle” and “LAS” show the marking that corresponds to a nominal nozzle size number of 100.
BE CAREFUL: accessible surfaces of the appliance can reach high temperature during operation.

DISPOSAL

Upon expiry of its service life the appliance can be disposed of separately from ordinary domestic waste. You can turn it over to a specialized electric and electronic appliance disposal and recycling centre.

CERTIFICATION DATA, GUARANTEE

The service life of this item is 5 years since the date of sale to the end user, provided the item will be used in strict accordance with the present manual and the applicable technical standards. Upon expiry of the service life please contact the nearest authorized service centre for suggestions as to further operation of the appliance. The manufacturing date of the appliance is integrated into the serial number (digits 2 and 3 – year, digits 4 and 5 – month of manufacture). If any questions related to appliance maintenance should arise, or if the appliance has malfunctions, apply to the CENTEK TM Authorized Service Center. The address of the service center can be found on the website https://centek.ru/servis. Service support contacts: Phone: +7 (988) 24-00-178, VK: vk.com/centek_krd. General Service Center: OOO «Larina-Serves», Krasnodar, Phone: +7 (861) 991-05-42.
The product has the Certificate of Conformity.

MANUFACTURER AND IMPORTER INFORMATION

I mop rated to EAEU by: I ndividualniy Predprinimatel Saruman Karo Shurikovich. Address: Russia, 350912 Krasnodar, ul. Ataman Lysenko, 23, put. Pashkovskiy. Phone: +7 (861) 2-600-900.

DEAR VALUED CONSUMER!
The guarantee period for all appliances amounts to 12 months since the date of sale to the end consumer. With this Warranty Card the Manufacturer confirms the proper condition of the appliance and undertakes to repair, free of charge, all defects caused by the Manufacturer’s default.

GUARANTEE MAINTENANCE TERMS

The guarantee shall be valid if the following documentation conditions are observed:
• The original Warranty Card shall be filled out correctly and clearly, indicating the of appliance model, serial number and sale date, the stamp of the seller company and signature of its representative shall be available, as well as the stamps on each coupon and the buyer’s signature in the Warranty Card.
The Manufacturer reserves the right to reject guarantee maintenance if the buyer fails to provide the abovementioned documents or if the information contained therein is incomplete, illegible or ambiguous.
The guarantee shall be valid if the following operation conditions are observed:
• the appliance is used in strict accordance with the present manual;
• the safety rules and requirements are observed.
The guarantee does not apply to regular maintenance, cleaning, installation and setup of the appliance at the owner’s location.
The guarantee does not apply in the following cases:
• mechanical damage;
• normal wear of the appliance;
• non-observance of operation requirements or erroneous actions on the part of the user;
• improper installation or transportation;
• natural disasters (lightning, fire, flood, etc.), as well as any other causes beyond the Manufacturer’s or Seller’s control;
• ingress of foreign objects, liquids or insects into the inside of the appliance;
• repairs or modifications to the appliance by unauthorized persons;
• use of the appliance for commercial purposes (loads exceeding normal domestic application), connection of the appliance to utility and telecommunication networks incompliant with national technical standards;
• failure of the following accessories, if replacement of these is allowed by design and does not involve disassembly of the appliance:
a) remote control units, rechargeable batteries, replaceable batteries (power cells), external power supply units and chargers;
b) consumables and accessories (packaging, covers, slings, carry bags, mesh screens, blades, flasks, plates, supports, grilles, spits, hoses, tubes, brushes, nozzles, dust collectors, filters, smell absorbers);
• for battery-powered appliances – operation with inappropriate or depleted batteries;
• for rechargeable battery-powered appliances – any damage caused by improper battery charging and recharging.
The present guarantee is provided by the Manufacturer in addition to the consumer rights determined by the applicable legislation and does not limit these rights in any way.
The Manufacturer shall not be made liable for possible damage, directly or indirectly inflicted by CENTEK brand products on people, domestic animals, the consumer’s or third persons’ property if such damage is inflicted as the result of non-observance of appliance installation and operation requirements, deliberate or negligent actions (omission) by the consumer or third persons, as well as of force majeure circumstances.
Service centers will only accept appliances in a clean state (there should be no food residues, dust and other contamination on the appliance). The Manufacturer reserves the right to change the design and specifications of the appliance without prior notice.

TROUBLESHOOTING

PROBLEM	POSSIBLE METHODS OF DISPOSAL
The cooker will not fire up	• Gas bottle is empty (replace bottle)

• Gas supply closed (open supply valve)
• Gas hose squeezed (spread out the hose)
• Burner(s) wet or clogged (dry or clean burner(s))
Yellow or uneven flame| • Gas in bottle running out (replace bottle)
• Burners incorrectly installed (seat burners correctly)
Smell of gas| • Gas hose connection leaky (check tightness with soap suds)
• Leak in pressure reducer (replace reducer)
• Control knob not fully closed (check position of control knob)

WARRANTY CARD

ATTENTION! Please require the seller to fill out the warranty card and tear-off coupons in full

PRODUCT

MODEL

SERIAL NUMBER

DATE OF SALE

This tear-off coupon is filled in by a representative of the seller

PRODUCT

MODEL

SERIAL NUMBER

DATE OF SALE

COMPANY-SELLER