MPS TBMA Test Board MagAlpha Sensors Owner’s Manual
- June 11, 2024
- MPS
Table of Contents
MPS TBMA Test Board MagAlpha Sensors
DESCRIPTION
The TBMA is a test board for the MagAlpha magnetic position sensor family. The TBMA allows users to run and test MagAlpha sensors quickly. TBMA boards come in two different formats: round (RD) and long (LT). In the RD format, the sensor is mounted in an end-of shaft configuration. In the LT format, the sensor is mounted on the edge of the board and can be used in both side-shaft and end-of-shaft configurations.
The TBMA is compatible with the Macom kit, offering seamless connection and operation of the MagAlpha and allowing users to evaluate MagAlpha functionalities and performances with their own set-up.
Contrary to the EVMA, the TBMA test board only includes the assembled board with the sensor and decoupling capacitors. It does not include connectors.
FEATURES
- Round Board Format for End-of-Shaft Mounting
- Long Board Format for Side Shaft and Endof-Shaft Mounting
- Compatible with MagAlpha Communication Interface Kit (EVKT-MACOM)
APPLICATIONS
- Servo Drives
- Robotics
- Automotive
- BLDC Motor Commutation
- Encoders
All MPS parts are lead-free, halogen-free, and adhere to the RoHS directive.
For MPS green status, please visit the MPS website under Quality Assurance.
“MPS” and “The Future of Analog IC Technology” are registered trademarks of
Monolithic Power Systems, Inc.
OVERVIEW
BOARD TYPE
Different board types are available, and each has a different schematic and
layout design (see Table 1). The board type to use is determined by the
selected sensor part number.
Each board type is also available in two different formats: a round shape test
board (RD), or a long shape test board (LT). The board part number specifies
which format is used:
- TBMAXXX-Q-RD-XXX = round shape test board
- TBMAXXX-Q-LT-XXX = long shape test board
Both RD and LT board formats can be used for end-of-shaft configurations where the sensor is positioned at the end of the motor or knob shaft. For side-shaft configurations where the sensor is positioned perpendicularly to the motor or knob shaft, only the RD board format can be used.
Table 1: Board Type
Board Type | Board Part Number | MPS Chip Part Number |
---|---|---|
Board type 1 | TBMA100-Q-RD-00A | MA100 |
TBMA100-Q-LT-00A
TBMA300-Q-RD-00A| MA300
TBMA300-Q-LT-00A
TBMA700-Q-RD-00A| MA700
TBMA700-Q-LT-00A
TBMA750-Q-RD-00A| MA750
TBMA750-Q-LT-00A
NOTE:
Availability of this option depends of the chip part ID. Please refer to the part datasheet directly.
Board type 2
NOTE:
Availability of this option depends of the chip part ID. Please refer to the part datasheet directly.
| TBMA102-Q-RD-01A| MA102
TBMA102-Q-LT-01A
TBMA302-Q-RD-01A| MA302
TBMA302-Q-LT-01A
TBMA310-Q-RD-01A| MA310
TBMA310-Q-LT-01A
TBMA702-Q-RD-01A| MA702
TBMA702-Q-LT-01A
TBMA710-Q-RD-01A| MA710
TBMA710-Q-LT-01A
TBMA730-Q-RD-01A| MA730
TBMA730-Q-LT-01A
TBMA800-Q-RD-01A| MA800
TBMA800-Q-LT-01A
TBMA820-Q-RD-01A| MA820
TBMA820-Q-LT-01A
TBMA850-Q-RD-01A| MA850
TBMA850-Q-LT-01A
TBMA CONTENT
Figure 2 shows a list of TBMA test board contents.
- One TBMA board with MagAlpha mounted (RD or LT)
- Decoupling capacitors
- Connector footprints (connectors not included)
BOARD TYPE 1
RD Format Overview
Figure 3 shows an overview of the Type 1 round (RD) board type.
LT Format Overview
Figure 4 shows an overview of the Type 1 long (LT) board type.
Schematic
Figure 5 shows a schematic for the Type 1 board.
Bill of Materials
The Type 1 board bill of materials (BOM) is shown in Table 2.
Table 2: Bill of Materials Type 1
Quantity| Designator| Description| Value|
Manufacturer| Manufacturer PN
---|---|---|---|---|---
2| C1, C4| Ceramic Capacitor; 10V; X6S; 0402| 1µF| Murata| GRM155C81A105KA12D
1| C2
(optional)
| Ceramic Capacitor; 10V; X6S; 0402| 1µF| Murata| GRM155C81A105KA12D
1| C3
(optional)
| Ceramic Capacitor; 16V; X7R; 0402| 100nF| Murata| GRM155R71C104KA88J
1| U1| MagAlpha Magnetic Position Sensor| MAxxx| MPS|
2| CN1, CN2
(not populated)
| 8 Position Receptacle
Connector 0.100″ (2.54mm), Surface Mount Tin
| | Würth Elektronik or
TE Connectivity
| 690367280876
or
7-2178711-8
Assembly View
Figure 6 shows the top side assembly view of the Type 1 round board. Figure 7
shows the top side assembly view of the Type 1 long board.
Mechanical Drawing
Figure 8 shows the top side mechanical drawing of the round board. Figure 9
shows the top side mechanical view of the long board.
Connector Pinout
Figure 10 shows the connector pinout of the Type 1 round board. Figure 11
shows the connector pinout for the Type 1 long board.
See Table 3 for Type 1 pin registers.
Table 3: Connector Pin Mapping Type 1
Pin | Name | Description |
---|---|---|
CN1.1 | VDD | 3.3V supply. |
CN1.2 | GND | Ground. |
CN1.3 | VFLASH | Flash power supply (3.9V only powered during flashing). |
CN1.4 | CS | Chip select (serial). |
CN1.5 | SCLK | Clock (serial). |
CN1.6 | MISO | Master in slave out (serial). |
CN1.7 | MOSI | Master out slave in (serial). |
CN1.8 | – | Leave unconnected. |
CN2.1 | U (1) | U output (optional motor commutation). |
CN2.2 | V (1) | V output (optional motor commutation). |
CN2.3 | W (1) | W output (optional motor commutation). |
CN2.4 | A (1) | A output (optional incremental encoder). |
CN2.5 | B (1) | B output (optional incremental encoder). |
CN2.6 | Z (1) | Z output (optional incremental encoder). |
CN2.7 | TEST | Test pin. |
CN2.8 | PWM (1) | Pulse width modulation output (optional). |
NOTE:
- Availability of this option depends of the chip part ID. Please refer to the part datasheet directly.
BOARD TYPE 2
RD Format Overview
Figure 12 shows an overview of the Type 2 round (RD) board type.
LT Format Overview
Figure 13 shows an overview of the Type 2 long (LT) board type.
Schematic
Figure 14 shows a schematic for the Type 2 board.
Bill of Materials
The Type 2 board bill of materials (BOM) is shown in Table 4.
Table 4: Bill of Materials Type 2
Quantity| Designator| Description| Value|
Manufacturer| Manufacturer PN
---|---|---|---|---|---
1| C1| Ceramic Capacitor; 10V; X6S; 0402| 1µF| Murata| GRM155C81A105KA12D
1| C2 (not populated)| Ceramic capacitor; 16V; X7R; 0402| 100nF| Murata|
GRM155R71C104KA88J
1| U1| MagAlpha Magnetic Position Sensor| MAxxx| MPS|
2| CN1, CN2
(not populated)
| 8 Position Receptacle
Connector 0.100″ (2.54mm), Surface Mount Tin
| | Würth Elektronik or
TE Connectivity
| 690367280876
or
7-2178711-8
Assembly View
Figure 15 shows the top side assembly view of the Type 2 round board.
Figure 16 shows the top side assembly view of the Type 2 long board.
Mechanical Drawing
Figure 17 shows the top side mechanical drawing of the Type 2 round board.
Figure 18 shows the top side mechanical view of the Type 2 long board.
Connector Pinout
Figure 19 shows the connector pinout of the Type 2 round board. Figure 20
shows the connector pinout for the Type 2 long board.
See Table 5 for Type 2 pin registers.
Table 5: Connector Pin Mapping Type 2
Pin | Name | Description |
---|---|---|
CN1.1 | VDD | 3.3V supply. |
CN1.2 | GND | Ground. |
CN1.3 | – | – |
CN1.4 | CS | Chip select (serial). |
CN1.5 | SCLK | Clock (serial). |
CN1.6 | MISO | Master in slave out (serial). |
CN1.7 | MOSI | Master out slave in (serial). |
CN1.8 | TEST | Test pin. |
CN2.1 | IO6 (2) | Pin 15 (IO). |
CN2.2 | IO1 (2) | Pin 1 (IO). |
CN2.3 | IO5(2) | Pin 9 (IO). |
CN2.4 | IO4 (2) | Pin 6 (IO). |
CN2.5 | IO2 (2) | Pin 2 (IO). |
CN2.6 | IO3 (2) | Pin 3 (IO). |
CN2.7 | MGL (3) | Magnetic level low (optional). |
CN2.8 | MGH (3) | Magnetic level high (optional). |
NOTES:
2) Please, refer directly to the chip datasheet to know which features are
available on these pins.
3) Availability of this option depends of the chip part ID. Please refer to
the part datasheet directly.
MAGNET SUPPLIERS
Table 6 shows a non-exhaustive list of possible magnet suppliers. The magnetization direction must be chosen wisely given the fact that most sold magnets are often axially magnetized, which is not a magnetization direction usually required in magnetic angle sensing applications. Angle sensing applications typically use diametrically magnetized magnets.
Table 6: Magnet Suppliers
Company | Website | Address |
---|---|---|
Maurer Magnetics AG | www.maurermagnetic.ch |
Industriestrasse 8
8627 Grüningen Switzerland
Arnold Technologies AG| www.arnoldmagnetics.com| Hübelacherstrasse 15
5242 Birr-Lupfig Switzerland
Bomatec AG| www.bomatec.com| Hofstrasse 1
8181 Höri Switzerland
Dexter Magnetic Technologies| www.dextermag.com| 1050 Morse Avenue
Elk Grove Village, IL 60007-5110 USA
JPMF| www.jpmf.com.cn| 8 LongWan Road Jiangmen City
GuangDong Province China
Binicmagnet| www.binicmagnet.com| Unit 612
Yuanzhong Building No. 1905 Hongmei Road Shanghai P. R. China 200233
China Rare Earth Magnet|
www.permanentmagnet.com| Room 705, Tower A
Century Holiday Plaza
9030 Shennan Rd Nanshan District Shenzhen China
Goudsmit Magnetic Systems| www.goudsmit-magnetics.nl| Petunialaan 19
5582 HA Waalre Netherland
Maurer Magnetic
Maurer Magnetic has a selection of diametrically magnetized magnets well-
suited for contactless rotary angle applications (see Figure 21 and Figure
22). Samples of the types mentioned below should always be available with no
lead time.
See Table 7 for a list of Maurer Magnetic magnets.
Table 7: Maurer Magnetic Diametrically Magnetized Magnets
OD (mm)| ID (mm)| H (mm)| Material| Remanence (Br)
(T)| Magnetization| Part Number
---|---|---|---|---|---|---
4.0| –| 3.0| N35| 1.2| Diametrical| M610403
4.0| –| 3.0| Sm26/16-17| 1.08| Diametrical| M410403
5.0| –| 2.5| N35| 1.2| Diametrical| M610502
5.0| –| 2.5| Sm26/16-17| 1.08| Diametrical| M410502
5.0| 1.25| 2.5| N35| 1.2| Diametrical| M610512
5.0| 1.25| 2.5| Sm26/16-17| 1.08| Diametrical| M410512
6.0| –| 2.5| N35| 1.2| Diametrical| M610602
6.0| –| 2.5| Sm26/16-17| 1.08| Diametrical| M410602
6.0| 1.5| 2.5| N35| 1.2| Diametrical| M610612
6.0| 1.5| 2.5| Sm26/16-17| 1.08| Diametrical| M410612
6.0| 1.5| 3.0| N35| 1.2| Diametrical| M610613
6.0| 1.5| 3.0| Sm26/16-17| 1.08| Diametrical| M410613
8.0| –| 2.5| N35| 1.2| Diametrical| M610802
8.0| –| 2.5| Sm26/16-17| 1.08| Diametrical| M410802
NOTICE: The information in this document is subject to change without notice. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications.
www.MonolithicPower.com
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and
Duplication Prohibited.
© 2017 MPS. All Rights Reserved.
References
- Industrial Magnet Manufacturer | Arnold Magnetic Technologies
- BINIC MAGNET Co.,LTD
- Home - Bomatec
- Permanent Magnet & Custom Magnetic Assemblies | Quality Manufacturer
- Driven by magnetism | Goudsmit Magnetics
- 江益磁材
- Maurer Magnetic AG - Home
- MPS | Monolithic Power Systems
- Permanent Magnets - China Rare Earth Permanent Magnet Manufacturers
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>