Munters FH1707 Free Hanging Hanger Kit Instruction Manual

Munters FH1707 Free Hanging Hanger Kit

Thank You:
Thank you for purchasing a Munters FH1707 Hanger Kit. Munters equipment is designed to be the highest performing, highest quality equipment you can buy. With the proper installation and maintenance it will provide many years of service.

Please Note:
To achieve maximum performance and ensure long life from your Munters product it is essential that it be installed and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:
For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the
Munters Corporation office at 1-800-227-2376 or by e-mail at aghort.info@munters.com.

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have been properly installed, maintained and operated under competent supervision, according to the instructions provided by Munters Corporation.
• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation or maintenance shall not be considered a defect under the Warranty.

Unpacking the Equipment

Before beginning installation, check the overall condition of the equipment. Remove packing materials, and examine all components for signs of shipping damage. Any shipping damage is the customer’s responsibility and should be reported immediately to your freight carrier.

Parts List

Each FH1707 includes:

• 1 – Horizontal Hanger Bracket, (73”L.) GZ
• 2 – Vertical Hanger Arms, (24”L.) GZ
• 1 – Hardware Package as follows:

Dimensions

Installation Instructions

Assembly

• Step 1
  Attach (2) Eye Bolts [A] to Horizontal Hanger Bracket using (2) Nuts [B]. See Figure 1.

• Step 2
  Attach each of the two Vertical Hanger Arms to the Horizontal Hanger Bracket using (3) Bolts [C] and Nuts [D], making sure the opening in the “C” channel faces outward and the angled “Foot” is pointing down and out. Then add (2) Bolts [C] and Nuts [D] to the lower pair of holes in the Hanger Arms. See Figure 2.

• Step 3
  On the bracket on the top of the fan, remove the (2) bolts and nuts as shown and discard. Also, remove the (2) bolts and nut from the end of the upper angled struts where they are bolted to the Orifice and discard. See Figure 3. (Do Not Reuse these bolts and nuts).

Installation Instructions

• Step 4A
  Place the Hanger Bracket Assembly on the top of the fan with the Horizontal Hanger Bracket over the Bracket on the top of the fan with the shorter side of the bracket on the Prop Side of fan and the longer side of bracket on the motor side and secure in place using (4) Bolts [C] and Nuts [D]. See Figure 4.

• Step 4B
  The Angled Foot on the Vertical Hanger Arms should line up with the holes in the orifice and strut whree the bolts and nuts were removed previously. Fasten the Hanger Arms to the orifice/stut using (2) Bolts [C] and Nuts [D]. See Figure 4. (Do Not Reuse bolts and nuts removed previously).

• Step 5
  Install (2) Eye Bolts [A] to the bottom bracket of fan in the larger hole next to the pre-installed bolt with they eye on the motor side of the fan and secure in place using (2) Nuts [B]. See Figure 5.

• Step 6
  Hang Fan Assembly from each Eye Bolt [A] in the Horizontal Hanger Bracket. Chains, S-Hooks and other hanging material are not provided. Hanging material and hanging points must be rated for 2,100 lbs. (950 Kg). Chains must not run straight up, but should be at a slight angle. See Figure 6. The Slots in the Horizontal Hanger Bracket can be used to lift the fan with the forks of Lift Truck or Tractor. Make sure to use care when lifting fan, so as not to damage fan.

• Step 7
  If it is desired to angle the hanging fans down, attach chains and s-hooks (not provided) to the Eye Bolts [A] attached to the bracket on the bottom of the fan and secure chains to give the fan desired angle.
  See Figure 7.

Munters Europe AB, Isafjordsgatan 1, P.O. Box 1150, SE-164 26 Kista, Sweden. Phone +46 08 626 63 00, Fax +46 8 754 56 66.
Munters Corporation 2691 Ena Drive Lansing, MI 48917 U.S.A. Phone +1 800-227-2376, Fax +1 517-676-7078 www.munters.us

• Australia Munters Pty Limited, Phone +61 2 6025 6422,
• Brazil Munters Brasil Industria e Comercio Ltda, Phone +55 41 3317 5050,
• Canada/US Munters Corporation Lansing, MI Phone +1 517 676 7070,
• China Munters Air Treatment Equipment (Beijing) Co. Ltd, Phone +86 10 80 481 121,
• Denmark Munters A/S, Phone +45 9862 3311, India Munters
• India, Phone +91 20 3052 2520, Indonesia Munters, Phone +62 818 739 235,
• Italy Munters Italy S.p.A., Chiusavecchia, Phone +39 0183 52 11,
• Japan Munters K.K., Phone +81 3 5970 0021,
• Korea Munters Korea Co. Ltd., Phone +82 2 761 8701,
• Mexico Munters Mexico, Phone + 52 818 262 54 00,
• Russia Munters AB, Phone +7 812 448 5740,
• Singapore Munters Pte Ltd., Phone +65 744 6828,
• South Africa and Sub-Sahara Countries Munters (Pty) Ltd., Phone +27 11 997 2000,
• Spain Munters Spain S.A., Phone +34 91 640 09 02,
• Sweden Munters AB, Phone +46 8 626 63 00,
• Thailand Munters Co. Ltd., Phone +66 2 642 2670,
• Turkey Munters Form Endüstri Sistemleri A.Ş, Phone +90 322 231 1338,
• USA Munters Corporation Lansing, MI Phone + 1 517 676 7070,
• Vietnam Munters Vietnam, Phone +84 8 3825 6838,
• Export & Other countries Munters Italy S.p.A., Chiusavecchia Phone +39 0183 52 11

References

• Industrial Dehumidifier & Dehumidification Systems Manufacturer | Munters

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>