EURRION VISION S FCN48TASF Sharkfin Camera Installation Guide

EURRION VISION S FCN48TASF Sharkfin Camera

Installation Guide

This Installation Guide will help you install and adjust the camera properly. For further support and to download the complete user manual please visit
https://furrion.com/pages/download-navigation.

Prepare

1. Ensure that all items in your package match those shown in the ‘What’s in the box’ section on the packaging box.
2. Before installation, please read and understand all the important safety-related instructions from the online user manual.
3. Prepare tools you may need, including a #2 Phillips head screwdriver, sealant, insulation tape, pencil and/or a 5/8″ hole saw (needed only when drilling a new hole).

Mount bracket

Note : Skip this section if your RV is pre-installed with a bracket for camera installation.
IMPORTANT : Before any installation and wiring operation, remove the key from the ignition and isolate the 12V / 24V power source.
Always seek professional assistance if you are unsure about the installation and wiring operation.

1. Determine the mounting location on your RV. Ensure that there is no obstacle blocking the camera view. The recommended mounting location is shown below:
   – For rear camera position: At the top center on the rear of your RV and as high as practicable (2″ below the red marker light if available). – For doorway camera position: Above the top of the door.
   Note : The RV shown here is for reference only. You can mount Furrion Vision S products onto various types of long vehicles such as trailers and Class A/B/C motorhomes.
   

2. Use the gasket as a template to mark a basic outline on the chosen location with a pencil. Drill a 5/8″ center hole. Then route the female connector of the camera power cable through the hole and leave 2 inches of slack.
   

3. Connect the bare ends of the camera power cable to the nearest 12V / 24V power supply.
   – For rear camera position: You are suggested to share the same power line from the nearest marker light (such as the red marker light at the top center on the rear if available).
   – For doorway camera position: You are suggested to share the power line from your RV porch light (or the nearest light source from the RV/ trailer battery).
   Note : Ensure that the fuse on the connected power line provides additional 1A fusing current for the camera. Ensure proper cable isolation for all bare ends (e.g., by using insulation tape).

4. Fix the gasket and bracket with four #6×3/4″ flat selftapping screws. If the mounting surface is uneven, apply sealant around the gasket for better sealing.
   

Mount camera

If this camera comes in a bundle with a Furrion Vision S monitor, it is paired with the monitor by default. You can connect it to the female connector on the Y type power cable of the monitor and resume power temporarily to check the pairing status before installation.
If you cannot find the video of the camera on the monitor screen or you have an unbundled camera, see the Quick Start Guide for the monitor or online user manual for the pairing procedures.

1. Mount the antenna onto the camera securely and keep the antenna straight.
   

2. If there is a cover on the bracket housing, remove it first. Connect the female connector of the camera power cable to the male connector on the back of the camera, and put the redundant cables inside the bracket housing. Then attach the camera to the bracket with four #4×1/4″ self-tapping screws.
   

3. Adjust the view angle of the camera by rotating it upwards and downwards (0-50°) so that you can see:
   (For rear camera position): the bottom edge of your vehicle and the road conditions behind;
   (For doorway camera position): the bottom edge of the door.
   

Welcome

Thank you for purchasing the Furrion® Sharkfin Camera. Before operating your new product, please read these instructions carefully. This will ensure safe use and reduce the risk of injury. This instruction manual contains information for installation, maintenance of the product and safe use.
Please keep this instruction manual in a safe place for future reference. Be sure to pass on this manual to any new owners of this product. The manufacturer does not accept responsibility for any damages due to not observing these instructions.
If you have any questions regarding our products, please contact us at: support@furrion.com

Important Safety Instructions

READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR USING THE SYSTEM
This product is intended to assist in safe driving and to allow the driver to have a broader view while the vehicle is in reverse.
You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to your local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving.
Your first priority while driving should always be the safe operation of your vehicle. Furrion cannot accept any responsibility for accidents resulting from failure to observe these precautions or safety instructions.

1. This product utilizes high voltage. Any unauthorized modifications or damage to the product may result in electrical shock. Handle all components with care. Inspect regularly for damage to components and cabling.
2. You are responsible for ensuring the installation of this product does not void or affect the vehicle manufacturer’s warranty. Furrion is not liable in full or in part for improper installation resulting in loss or damage to your property, or for voiding all or part of the vehicle manufacturer’s warranty.
3. Do not apply excessive force to any of the components contained within this kit. Excessive force used before, during or after installation that results in a damaged or nonfunctional part will void all warranties.
4. Please follow the procedures in this instruction manual. Improper installation or modification of this product will void all warranties.

Many jurisdictions have laws and regulations relating to the use of cameras and some do not allow for the obstruction of information contained on a license plate. Before using this product, it is the buyer’s responsibility to be aware of and comply with any applicable laws and regulations that apply to license plates or may prohibit or limit the use of cameras.

Electrical Safety

• A battery or 12V DC electrical system presents a risk of electrical shock or burn. Ensure all power sources are isolated before installation.
• Insulate unconnected wires with vinyl tape or similar.
• Use insulated tools when working with a power supply

Caution

• There are no serviceable parts in the Furrion Wireless Observation Camera System. Do not disassemble or attempt any repairs.
• There are no fuses or disconnects in the Furrion Wireless Observation Camera System. Install external fuses/ breakers as required.

Installation

• Installation and wiring of this product require specialist skills. To ensure proper and safe installation, please seek a specialist technician.
• Only use supplied or recommended parts.
• Use watertight connectors for the camera power supply cable to power source.
• Connect the camera to a 12-24V DC circuit using 18AWG or larger cables.
• Ensure correct polarity of DC power supply to the camera.
• To reduce the risk of fire, connect the camera only to a circuit provided with a maximum branch-circuit over current protection device.
• Do not route wiring in areas that may get hot.
• Take necessary precautions when working at elevated levels.

Use

• Electrical appliances and overhead power lines can affect the wireless signal.

Care

• Do not wash the vehicle with an automatic car wash or high pressure water. This may damage the camera.
• Use a wet cloth to clean the camera lens. A dry cloth may scratch the camera lens.

FCC Statement

The equipment complies with RF exposure limits. This module is limited to installation in mobile or fixed applications. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE : The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure
The device has been evaluated to meet general RF exposure requirement.
To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

IC Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

RF Exposure
The device has been evaluated to meet general RF exposure requirement. To maintain compliance with RSS-102 — Radio Frequency (RF) Exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Product Overview

Product Description

The Furrion Vision S Camera System is designed to assist the driver by providing a clear and wide image of the area behind the vehicle whenever the vehicle is shifted into reverse. Never rely solely on this product to ensure the area is clear of children and/or obstructions. Use your monitor and look both ways. This product is not intended to replace existing safety procedures, but rather to add an additional safety tool for your vehicle.
CAUTION : Do not back up your vehicle while watching the monitor screen. Always look in the direction the vehicle is traveling. Use the monitor as an aid to ensure there are no children or obstructions. The image on the monitor is not designed to show distance and may be misleading. The actual distance is less than appears in the monitor. The range of the image is limited. Be aware of blind spots.

Panel

Getting Started

The camera and monitor need to be paired the first time you are using your Vision S Camera System.
NOTE : Ensure both the camera and monitor have power supplied during Pairing and setting processes. (The vehicle may need to be running.)

Pairing the 4.3” Vision S Camera System

1. Use or button to highlight PAIRING menu, then press to enter the next page.
   

2. Press the “MONITOR PAIRING” button at the bottom of selected camera to pair.
   
   

3. Once paired successfully, a red icon will appear after the device list.
   
   

4. An icon indicates pairing failed, repeat steps 2 and 3 to pair again.
   

5. . Repeat steps 1 to 4 to pair the other cameras.

6. Refer to “Camera Settings” section for detail settings of the camera.

Pairing the 5“ and 7” Vision S Camera System

1. Touch PAIRING on screen. The PAIRING will be highlighted in red once selected and enter the submenu automatically.
   

2. Select the desired camera you are going to pair. Press “MONITOR PAIRING” button at the bottom of the selected camera for 3 seconds to pair.
   NOTE : The monitor can only pair to one camera for each channel and a total of four cameras are supported.
   
   

3. Once paired successfully, a red icon will appear after the device list.
   
   

4. An icon indicates pairing failed, repeat steps 2 and 3 to pair again.
   
   

5. Repeat steps 1 to 4 to pair the other cameras.

6. Refer to “General Setup” section on detail settings of the camera.

Installation

COMPLETELY READ THIS MANUAL BEFORE INSTALLATION
NOTE : We have included all of the items needed for most standard installations, but all vehicles are different. We recommend you review your vehicle completely before starting.

What’s in the box

Make sure you have all the following items included in the packaging. If any item is damaged or missing, contact your dealer.

• Camera
• Antenna x 1
• Warranty Card x 1
• Instruction Manual x 1

NOTE : The contents included may be different based on the kit you purchased. Please take the actual product as standard.

Suitable Installation Position

CAUTION
Ensure there are no electrical cables, gas lines, pipes or other important parts behind where the drill holes will be.
To prevent the risk of electric shock or fire, during installation, remove the key from the ignition and isolate the 12V or 24V power source.

• For optimum performance, the camera should be mounted where there is minimal obstruction between the camera and monitor. Dense side-wall material and electrical appliances can reduce signal strength.
• Where practical install, as high as possible at the rear of the vehicle.
• Horizontal-center of the vehicle or as close as is optimal.
• Mount camera at least 2 inches above or below running lights. Close proximity to lights may cause image blooming, blurring and reduced night vision performance.
• The area should be flat with enough surface area to accommodate the bracket.
• The surface area should be clean and dry for a watertight installation.
• Ensure that power can be fed to the installation area from within the vehicle.
  

Camera Installation

1. Select a suitable mounting position where you are going to install the doorway camera. Mark a basic outline using the provided bracket gasket. (Fig. 1)
   

2. Drill a 5/8” center hole on the vehicle wall using a 5/8” hole saw. (Fig. 2)
   

3. Feed the supplied 6-foot camera power cable through the gasket. Ensure the bare end of the cable goes into the vehicle and the flat side faces inward. (Fig. 3)
   

4. Pull out the camera power cable, leaving approx 2 inches of slack. (Fig. 4)
   

5. Install the antenna onto the camera and rotate clockwise to lock into place. (Fig. 5)
   

6. Connect the camera power cable to the camera cable. (Fig. 6)
   

7. Place the attached cables and connections into the bracket housing by first placing the cable to the right.
   Place the camera cable filter in the left of the bracket housing. (Fig. 7)
   

8. . Fix the gasket and bracket to the vehicle using four 3/4 ” flat self-tapping screws. Make sure the camera power cable is not damaged while attaching the device to the vehicle. (Fig. 8)
   

9. Make sure the sealing lip around the edge of the gasket is seated over the edge of the bracket before fully tightening the screws.

Connecting the Camera

WARNING
When connecting wires, ensure the circuit is isolated by disconnecting the negative terminal on the battery.

• Ensure correct polarity when  wiring the cables. RED + BLACK -.
• Ensure correct polarity when wiring.
• Wire connections and terminals must be sealed and waterproof.

The Furrion Vision S Camera can be connected to an electrical power source via a 7 Way Connector.
Wiring to running lights: the camera will activate when the running lights are switched on.
Wiring to reverse lights: the camera will activate when the vehicle engages reverse gear.

Consult the vehicle’s service manual for specific wiring color code.

When wiring this camera directly to a 12V battery or converter in your RV, use an in-line switch on the power cable to power on or off your camera. This will enable this camera to be used when parked without a tow vehicle connected.

Specifications

Troubleshooting

power.
Make sure to hold the camera pairing button for 2 seconds.
Night vision is poor or does not function| The light sensor on the camera may be dirty or obstructed.
Ensure the camera unit is installed at least 2 inches away from rear lights.

Warranty

FURRION WARRANTS FOR A PERIOD OF 1 YEAR FROM DATE OF RETAIL PURCHASE BY THE ORIGINAL END-USE PURCHASER, THAT THIS PRODUCT, WHEN DELIVERED TO YOU IN NEW CONDITION, IN ORIGINAL PACKAGING, FROM A FURRION AUTHORIZED RESELLER AND USED IN NORMAL CONDITIONS, IS FREE FROM ANY DEFECTS IN MANUFACTURING, MATERIALS, AND WORKMANSHIP. IN CASE OF SUCH DEFECT, FURRION SHALL REPLACE OR REPAIR THE PRODUCT AT NO CHARGE TO YOU. THIS WARRANTY DOES NOT COVER: PRODUCTS WHERE THE ORIGINAL SERIAL NUMBERS HAVE BEEN REMOVED, ALTERED OR CANNOT READILY BE DETERMINED; DAMAGE OR LOSS CAUSED BY ACCIDENT, MISUSE, ABUSE, NEGLECT, PRODUCT MODIFICATION, FAILURE TO FOLLOW INSTRUCTIONS IN INSTRUCTION MANUAL, COMMERCIAL OR INDUSTRIAL USE; DAMAGE OR LOSS CAUSED TO THE DECORATIVE SURFACE OF PRODUCT; TO ANY DATA, SOFTWARE OR INFORMATION; AND NORMAL WEAR AND TEAR. THIS WARRANTY ONLY PROTECTS THE ORIGINAL END-USER (“YOU”) AND IS NOT TRANSFERABLE; ANY ATTEMPT TO TRANSFER THIS WARRANTY SHALL MAKE IT IMMEDIATELY VOID. THIS WARRANTY IS ONLY VALID IN THE COUNTRY OF PURCHASE.
THIS WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. FURRION SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF FURRION CANNOT LAWFULLY DISCLAIM IMPLIED WARRANTIES UNDER THIS LIMITED WARRANTY, ALL SUCH WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
No Furrion reseller, agent, or employee is authorized to make any modification, extension, or addition to this warranty.
FURRION IS NOT RESPONSIBLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPLACEMENT OF ANY EQUIPMENT OR PROPERTY, ANY COSTS OF RECOVERING, REPROGRAMMING, OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH FURRION PRODUCTS. FURRION’S TOTAL LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THIS PRODUCT PURSUANT TO THE TERMS OF THIS WARRANTY.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR EXCLUSIONS OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OR CONDITIONS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY BY STATE OR (WHERE APPLICABLE IN THE COUNTRIES WHERE FURRION HAS NON-US/CANADIAN AUTHORIZED DEALERS) COUNTRY. NO ACTION OR CLAIM TO ENFORCE THIS WARRANTY SHALL BE COMMENCED AFTER THE EXPIRATION OF THE WARRANTY
PERIOD.
Keep your receipt, delivery slip, or other appropriate payment record to establish the warranty period. Service under this warranty must be obtained
by contacting Furrion at warranty@furrion.com
Product features or specifications as described or illustrated are subject to change without notice.

Main Features

Specifications

Night Vision Distance   <16ft (5m)
CMOS Size 1/3”
Optical Lens F2.0
IR Cut Filter 850nm Automatic
View Angle/Degree 120°
Working Current (IR ON) <400mA＠12V
Working Current (IR OFF) <250mA＠12V
Camera Pixel 720 x 480
Waterproof  IP65

References

• Furrion - Reinventing luxury living – furrion-global
• arrow
• Furrion - Reinventing luxury living – furrion-global
• FAQ – furrion-global

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>