MPS EVKT-8847 MP8847 Evaluation Kit User Guide

June 11, 2024
MPS

MPS EVKT-8847 MP8847 Evaluation Kit

MPS EVKT-8847 MP8847 Evaluation Kit

Overview

Introduction
The EVKT-8847 is an evaluation kit for MP8847.The MP8847 is a highly integrated, high-frequency, synchronous, step-down switcher with an I2C control interface. The MP8847 can support up to 6A of current from a wide 2.7Vto 6V range with excellent load and line regulation. This kit allows for quick evaluation of the MP8847. By using the I2C, users can set the switching frequency, slew rate, work mode, and the output voltage.

Kit Content

EVKT-8847 kit contents: (items below can be ordered separately).

# Part Number Item Quantity
1 EV8847-D-00A MP8847GD evaluation board 1
2 EVKT-USBI2C-02 Includes one USB to I2C communication interface, one USB
cable, one ribbon cable 1
--- --- --- ---

MPS EVKT-8847 MP8847 Evaluation Kit 1

Features and Benefits

The MP8847 is highly customizable. Users can program the IC via the MPS I2C GUI.
⚠️ All changes made in I2C mode will NOT be retained once the EVB is powered down.

Features adjustable under each method are outlined below.

I2C

  • Selectable the output voltage
  • Selectable transition response
  • Selectable slew rate
  • Selectable switching frequency
  • Selectable output discharge
  • Selectable VIN_OVP
  • Selectable PG function
  • Selectable mode (PFM & CCM)
  • System enable
  • Status indication: ILIM, UVLO, VIN & Vout OVP, Vout UVP, PG, OTW

Kit Specifications

Feature Specification
Supply for Board 2.7V – 6V
Operating Input Voltage                                              2.7V – 6V
Operating Systems Supported                                     Windows XP, 7, and later
System Requirements                                                  Minimum 22.2MB free
GUI Software                                                              3 Register Controls: VSEL, System 1, System 2
EVB Size (L x W)                                                         6.3 cm x 6.3 cm

Section 1. Hardware Specifications

Personal Computer Requirements
The following must be minimally met to use the EVKT-8847.

  • Operating System of Windows XP, 7, or later
  • Net Framework 4.0
  • PC with a minimum of one available USB port
  • At least 22.2 MB of free space

EV8847-D-00A Specifications
The EV8847-D-00A is an evaluation board for the MP8847GD. For more information, please refer to the EV8847-D-00Adatasheet.

MPS EVKT-8847 MP8847 Evaluation Kit 2

Feature                               Specification
Supply for Board                  2.7V – 6V
Operating Input Voltage       2.7V – 6V
EVB Size (L x W)                 6.3 cm x 6.3 cm

EVKT-USBI2C-02 Specifications
The EVKT-USBI2C-02 refers to the communication interface, which connects the EVB, the PC, and its supporting accessories. It provides I2C and PMBus capabilities. Together with MPS Virtual Bench Pro and GUI tools, it provides a quick and easy way to evaluate the performance of MPS digital products. For more details, refer to the EVKT-USBI2C-02 datasheet.

MPS EVKT-8847 MP8847 Evaluation Kit 3

Section 2. Software Requirements

Software Installation Procedure
Programming occurs through the MPS I2C GUI. Follow the instructions below to install the software.
Note : This software can be downloaded directly from the MPS website.

  1. Visit the MP88xx I2C GUI page at https://www.monolithicpower.com/en/i2c-tool.html
  2. Click the “Download” button in the upper right-hand corner.
  3. Once the download has completed, double-click the .exe file to open the set-up guide (see Figure 4).MPS EVKT-8847 MP8847 Evaluation Kit 4If a protection window comes up, click “More info,” then click “Run anyway.”
  4. Follow the prompts in the set-up guide.
  5. Wait for status screen to verify that installation is complete (see Figure 5).

MPS EVKT-8847 MP8847 Evaluation Kit 5

Section 3. Evaluation Kit Test Set-Up

Hardware Set-Up
The hardware must be properly configured prior to use. Use the USB cable to connect the EVKT-USBI2C- 02 communication interface to the PC, and follow the instructions below to set up the EVB.

  1. Locate the proper wires to connect the EVB to the EVKT-USBI2C-02 communication interface.
  2. Connect SCL, SDA, and GND (see Figure 6). If needed, refer to the datasheet for further clarification.

MPS EVKT-8847 MP8847 Evaluation Kit 6

Powering up the EVB

  1. Connect the positive and negative terminals of the load to the VOUT and GND pins, respectively.
  2. Preset the power supply output to between 2.7V and 6V, and then turn off the power supply.
  3. Connect the positive and negative terminals of the power supply output to the VIN and GND pins, respectively.
  4. Turn the power supply on and make the EN voltage more than the threshold. The IC will enter the power-on sequence automatically.

Software Set-Up
After connecting the hardware according to the steps above, follow the steps below to use the GUI software.

  1. Start the software. It will automatically check the EVB connection.
    • If connection is successful, the address will be listed in the “Slave Address” (see Figure 7).MPS EVKT-8847 MP8847 Evaluation Kit 7
    • If the connection is not successful, a warning will appear at the bottom. There are two warnings a user can expect (see Figure 8). Each of the warnings mean an invalid connection.
    1. “EVB is Disconnected!” This means that the evaluation board is not connected.
    2. “Communication Board is Disconnected!” This means that the USB I2C communication interface is not connected.MPS EVKT-8847 MP8847 Evaluation Kit 8
  2. If connection is successful, proceed to Step 3. Otherwise, check connections between the EVB, communication interface, and PC. Re-plug the USB into the computer and restart the GUI.
  3. Click the PartSelect button to select the MP8867 (see Figure 7) (The default GUI window is for the MP8861). The Register Control menu will appear on the left side. The I2C register values will be read and displayed on the right side after clicking the Read button (see Figure 9).MPS EVKT-8847 MP8847 Evaluation Kit 9
  4. Find the item you want to change and select the desired value from the drop-down menu.
  5. Click the Read button to update the values. The changed information of the item will appear on the right side (see Figure 10).

MPS EVKT-8847 MP8847 Evaluation Kit 10

Troubleshooting Tips
Note : USBI2C-02 and USBI2C-01 drivers are not compatible. USBI2C-02 uses USBXpress and USBI2C- 01 uses Cyusb3. USBI2C-02 is the recommended device for the MPS PMBus and I2C.

EVKT-USBI2C-01
In case the USBI2C-01 driver is not properly installed, manual installation is required. Follow the steps below:

  1. Open the Device Manager and select update driver software (see Figure 11).
  2. Click “Browse my computer for driver software.”

MPS EVKT-8847 MP8847 Evaluation Kit 11

EVKT-USBI2C-02
In case the USBI2C-02 driver is not properly installed, manual installation is required. Follow the steps below:
Note: Check driver version. Find “USBXpress” Device in the Device Manager under USB controllers.

Right click and view properties. Check to make sure the driver version matches the newest version (see Figure 12).

MPS EVKT-8847 MP8847 Evaluation Kit 12

  1. Install the correct USBXpress “.exe” file.
    Choose either the 32 bit or 64 bit operating system:
    32-bit: USBXpressInstaller_x86.exe
    64-bit: USBXpressInstaller_x64.exe

  2. Connect the EVKT-USBI2C-02 communication interface to the PC with the USB cable.

No Supply
The MP8847’s input pin has an under-voltage lockout (UVLO) detection circuit. If the input voltage (AVIN) is lower than the UVLO rising threshold, the MP8847’s functions are disabled.

Shutdown Event
If the MP8847 detects that the input voltage is lower than the UVLO falling threshold (it enters a no supply state) or over-temperature protection is triggered (it enters a power-off state), the MP8847 switches to no supply state or power-off state, regardless of the current state.

Thermal Recovery
If the MP8847 is in a power-off state due to the die temperature exceeding the thermal protection threshold, the MP8847 enters a power-on sequence when the die’s temperature decreases.

Shutdown Sequence
When the input voltage is lower than the UVLO falling threshold, or the IC is over-temperature, the MP8847 enters the shutdown sequence directly.

Section 4. Ordering Information

The components of the evaluation kit can be purchased separately depending on user needs.

MPS EVKT-8847 MP8847 Evaluation Kit 13

Order directly from MonolithicPower.com or our distributors.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals