BALKENE HOME 64012 ARCADIA Media Console Instruction Manual
- June 4, 2024
- BALKENE HOME
Table of Contents
ARCADIA
MEDIA CONSOLE
Item#: 64012
ATTACH YOUR RECEIPT
Keep a copy of your proof of purchase or order confirmation, which will be
needed if you need to contact us about warranty coverage.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Questions, problems, missing parts?
Before returning to your retailer, our Florida-based customer service team is
available:
Call toll-free 866-985-7877| 9 am – 9
pm, EST
---|---
Email [email protected]|
Live Chat www.balkenehome.com | 9 am – 6 pm,
EST, Monday – Friday
INFORMATION
BEFORE YOU BEGIN
Before beginning assembly, make sure all parts are present. Compare parts
received with the “Parts List.” If any part is missing or damaged, do NOT
attempt to assemble the product. Please read and understand this entire manual
before attempting to assemble this product. If you have any questions
regarding the product, please contact Customer Service.
Call toll-free 866-985-7877| 9 am – 9
pm, EST
---|---
Email [email protected]|
Live Chat www.balkenehome.com | 9 am – 6 pm,
EST, Monday – Friday
GENERAL INFORMATION
This product is made of particle board and MDF. For safe assembly, work on a
dry, soft, secure, and clean surface. Do not clean with detergents or
chemicals. Do not sit or stand on the unit. Do not place damp or hot items
such as coffee cups directly on the surface of this item. Keep away from
direct sunlight and water. Do not drag the unit. For indoor use only.
SAFETY INFORMATION
WARNING
DO NOT sit or stand, or allow children to sit or stand on the assembled
product.
Make sure connectors are securely in place. Perform periodic checks to ensure
the connectors remain secure and adjust if needed. Keep unassembled parts and
hardware away from children and infants. This package contains small parts and
sharp edges. Adult assembly required.
CAUTION
READ all instructions before beginning assembly. Failure to do so may result
in faulty assembly and potential injury. Assemble the item on a soft,
nonabrasive surface such as carpet or cardboard to avoid damaging the item.
Max safe load limit:
Top: 20 KG / 44 LB
Top Open Shelves: 10 KG / 22 LB (each)
Lower Open Shelves: 8 KG / 17.5 LB
End Compartments: 8 KG / 17.5 LB (per shelf)
PARTS LIST
| PART | DESCRIPTION | QTY |
|---|---|---|
| A | Top Panel | 1 |
| B | Top Face Frame | 1 |
| C | Left Side | 1 |
| D | Right Side | 1 |
| E | Center Divider | 1 |
| F | Top Shelf | 1 |
| G | Top Backer | 1 |
| H | Left Divider | 1 |
| I | Right Divider | 1 |
| --- | --- | --- |
| J | Interior Shelf | 2 |
| K | Center Shelf | 1 |
| L | Side Backer | 2 |
| M | Center Backer | 1 |
| N | Center Face Frame | 1 |
| O | Left Face Frame | 1 |
| P | Right Face Frame | 1 |
| Q | Base Panel | 1 |
| --- | --- | --- |
| R | Base Front | 1 |
| S | Base Left Side | 1 |
| T | Base Right Side | 1 |
| U | Base Back | 1 |
| V | Door | 2 |
| W | Door Rail | 1 |
HARDWARE CONTENTS
YOU WILL NEED FOR ASSEMBLY:
(not included) Phillips-head screwdriver Mallet or hammer Power drill (to
anchor unit to a wall)
ASSEMBLY
-
Insert Cam Bolts 1 into the indicated holes in the left/Right Dividers H /I. Use a Phillips-head screwdriver to tighten.
Hardware Required: 1 Cam Bolt x4
ASSEMBLY NOTE: Use a Phillips-head screwdriver to tighten each Cam Bolt you install until its threads are fully inserted. -
Place Dowels 3 in the 2 holes between each pair of Cam Bolts 1 installed in Step 1.
Insert the Cam Bolts and Dowels installed in the Left Divider H into the corresponding holes in the left edge of the Center Shelf K as shown. Secure by inserting a Cam Nut 2 into each of the adjoining holes in the underside of the Center Shelf. Use a Phillips-head screwdriver to turn the Cam Nuts clockwise to secure the Cam Bolts.
Attach the Right Divider I to the right edge of the Center Shelf using the same method.
Hardware Required:
2 Cam Nut x4
3 Dowel x4
-
Insert 3 Cam Bolts 1 as indicated in the Center
Face Frame N. Use a Phillips-head screwdriver to tighten.
Hardware Required: 1 Cam Bolt x3
-
Attach the Door Rail W to the Center Face Frame N with 3 Hex Bolts14. Use the Hex Wrench 15 to tighten the Hex Bolts.
Hardware Required: 14 Hex Wrench
15 Hex Bolt x3
-
Place Dowels 3 in the 2 holes between the Cam Bolts 1 on the Center Face Frame N.
Insert the Cam Bolts and Dowels installed in the Center Face Frame into the corresponding holes in the front edge of the Top Shelf F as shown. Secure by inserting a Cam Nut 2 into each of the adjoining 3 holes in the underside of the Shelf. Use a Phillips-head screwdriver to turn the Cam Nuts clockwise to secure the Cam Bolts. Insert 4 Cam Bolts 1 as indicated in the underside of the Top Shelf.
Hardware Required:
1 Cam Bolt x4
2 Cam Nut x3
3 Dowel x2
-
Place 2 Dowels 3 in the bottom edge of the Center Divider E. Insert the Dowels into the holes at the center of the Top Shelf F.
Affix the 2 panels together by inserting 2 Screws 6 through the bottom of the Top Shelf and into the edge of the Center Divider. Use a Phillips-head screwdriver to tighten.
Hardware Required:
3 Dowel x2
6 Screw (4x35mm) x2
-
Insert Dowels 3 in the top edges of the Left/Right
Dividers H/ I.
Insert the Cam Bolts 1 installed in the underside of the Top Shelf F into the holes in the top edges of the Dividers. Secure by inserting a Cam Nut into each of the adjoining holes in the insides of the Dividers. Use a Phillips- head screwdriver to turn the Cam Nuts clockwise to secure the Cam Bolts.
Hardware Required:
2 Cam Nut x4
3 Dowel x4
-
Insert 3 Cam Bolts 1 per panel as indicated in the
Left/Right Face Frames O/P. Use a Phillips-head screwdriver to tighten.
Hardware Required: 1 Cam Bolt x6
-
Place Dowels 3 in the 2nd and 4th holes on the front edges of the Left/Right Sides C/D.
Insert the Cam Bolts 1 previously installed in the Left Face Frame O into the corresponding holes in the edge of the Left Side as shown. Secure by inserting a Cam Nut 2 into each of the adjoining holes in the Left Side. Use a Phillips- head screwdriver to turn the Cam Nuts clockwise to secure the Cam Bolts. Attach the Right Face Frame P to the Right Side D uses the same method. Insert 2 Cam Bolts 1 in each Side as indicated.
Hardware Required:
1 Cam Bolt x4
2 Cam Nut x6
3 Dowel x4
-
Insert 5 Dowels 3 into the indicated holes on the Left Side C.
Insert the Dowels and Cam Bolts 1 installed in the Left Side into the corresponding holes in the left edge of the
Top Shelf F/Center Face Frame N.
Secure by inserting a Cam Nut 2 into each of the 2 adjoining holes in the underside of the Top Shelf. Use a Phillips-head screwdriver to turn the Cam Nuts clockwise to secure the Cam Bolts. Lay the Top Face Frame B in place across the front of the Center Divider E as shown, sliding the left end onto the remaining Dowel in the Left Side.
Follow the above steps to attach the Right Side D to the right end of the unit.
Hardware Required:
2 Cam Nut x4
3 Dowel x10
-
Slide the Side Backers L and Center Backer M into the grooves along the back of the unit.
Insert 8 Dowels 3 into the bottom edges of the vertical panels C/H/I/D.
Secure the Base Panel Q in place using 8 Screws 6 as shown.
Hardware Required:
3 Dowel x8
6 Screw (4x35mm) x8
UNIT SHOWN UPSIDE-DOWN FOR EASIER COMPONENT INSTALLATION. -
Install a Cam Bolt 1 in each Base Side S/T.
Place a Dowel 3 into either end of the Base Back U. Insert the Cam Bolt installed in the Left Base Side S into the left edge of the Base Back. Insert a Cam Nut 2 in the adjoining hole and turn clockwise to secure the Cam Bolt.
Attach the Right Base Side T by the same method.
Hardware Required:
1 Cam Bolt x2
2 Cam Nut x2
3 Dowel x2
-
Install 2 Cam Bolts 1 in the Base Front R.
Place a Dowel 3 into the edge of the Left/Right Sides /. Insert the Cam Bolts in the Base Front into the base Sides.
Insert a Cam Nut 2 into each of the adjoining holes and turn clockwise to secure the Cam Bolts.
Hardware Required:
1 Cam Bolt x2
2 Cam Nut x2
3 Dowel x2
-
Place 8 Dowels 3 in the top edge of the assembled base.
Secure the base to the unit by inserting 10 Screws 8 through the bottom edge of the joined base pieces and into the bottom of the Base Panel Q.
Hardware Required:
3 Dowel x8
8 Screw (4x65mm) x10
-
Insert a total of 6 Cam Bolts into the indicated holes in the underside of the Top Panel A. Attach each Anchor Bracket near the back edge of the Top Panel using a Screw 5.
Hardware Required:
1 Cam Bolt x6
5 Screw (4x12mm) x2
12 Anchor Bracket x2
-
Place 10 Dowels 3 as indicated in the top edges of the Left Side C, Center Divider E, Right Side D, and Top Face Frame B.
Slide the Top Backer G into place in the groove at the top rear of the unit.
Insert the Cam Bolts in the Top Panel A into the top edges of the vertical panels. Insert a Cam Nut 2 into each of the adjoining holes and turn clockwise to secure the Cam Bolts.
Insert 3 Screws 7 through the bottom of the Top Face Frame and into the Top Panel. Tighten with a Phillips-head screwdriver.
Hardware Required:
2 Cam Nut x6
3 Dowel x8
7 Screw (4x50mm) x3
-
Install the Corner Brackets 10 at each corner of the Top/Side/Center Backers G /L/M.
Fasten each Corner Bracket using a Screw 9.
Hardware Required:
9 Screw (3x16mm) x16
10 Corner Bracket x16
-
Choose the desired installation height for each Shelf J. Insert the peg of each Shelf Bracket 4 into the appropriate holes in the interior of the left and right compartments of
the unit, with the horizontal tab, rotated to the top. Slide the Shelves into place in the left and right compartments.
Hardware Required: 4 Shelf Bracket x8
-
Attach 2 Hanger Rollers 18 to each Door V as shown using 2 Screws17 per Roller.
Hardware Required:
17 Screw (4x12mm) x8
18 Hanger Roller x4
-
Insert a Track Pin 11 into the holes in the Base Panel Q just in front of the Left/Right Dividers H /I.
Hang the Doors V by resting the wheels of the Hanger Rollers18 on top of the Door Rail W and settling the track on the bottom edge of each door onto a Track Pin.
Hardware Required: 11 Track Pin x2
-
Secure each Hanger Roller 18 to the Door Rail C using a Screw Bolt 16 as shown.
Hardware Required:
16 Screw Bolt (4x12mm) x4
-
Use Anchor Brackets 12 to anchor the unit to the wall for safety. The included hardware is appropriate for drywall installation and requires the use of a drill. If needed, consult a qualified tradesperson or online resources to safely anchor this unit.
Hardware Required:
6 Screw (4x35mm) x2
13 Drywall Anchor x2
Your Arcadia Media Console is ready for use!
LIMITED WARRANTY
Customers in the Contiguous US
With proof of purchase from an authorized retailer, this product is warranted
for a period of 1 year from the original purchase date against defects in
materials and workmanship under normal use. This warranty does NOT cover
normal wear/weathering, exposure to water, freezing temperatures, oils,
fluids, or chemicals OR use in a commercial context if the unit is not
designated as a commercial model. At Well Traveled Living’s sole discretion,
products under warranty will be repaired and/or replaced at no charge to the
customer. Returns sent back to Well Traveled Living must be sent via prepaid
freight in the original retail packaging.
For warranty service, contact Balkene Home/Well Traveled Living at the
address, phone number, or website and email listed in this owner’s manual. Be
sure to have your sales receipt, date of purchase and catalogue/model numbers
available when calling. All warranty service will be coordinated by Well
Traveled Living’s Amelia Island, Florida service center. This warranty is
extended only to the original owner. Proof of purchase will be required before
warranty service is rendered. The sales receipt is the only valid proof of
purchase. This warranty only covers failures due to defects in materials or
workmanship that occur during normal use. Failures and/or damage that result
from accident, negligence, misuse, abuse, neglect, mishandling, alteration or
modification, failure to maintain, improper assembly or maintenance, service
by unauthorized agency or use of unauthorized components or damage that is
attributable to acts of God are NOT covered.
This limited warranty gives you specific legal rights and you may also have
other rights which vary from jurisdiction to jurisdiction. The provisions of
the United Nations Convention on Contracts for the Sales of Goods shall not
apply to this limited warranty or the sale of products covered by this limited
warranty.
-
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED.
-
PURCHASER ASSUMES ALL RISKS IN THE ASSEMBLY AND OPERATION OF THIS UNIT.
-
FAILURE TO FOLLOW WARNINGS AND OPERATIONAL INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT IN SEVERE PROPERTY
DAMAGE AND/OR PERSONAL INJURY. -
IN NO EVENT WILL WELL-TRAVELED LIVING, OR ITS DIRECTORS, OFFICERS OR AGENTS BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY, WHETHER IN CONTRACT, IN TORT, OR ON ANY OTHER BASIS, FOR ANY INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR INCIDENTAL LOSS, COST, OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE, MAINTENANCE, USE, OR INABILITY TO USE THE PRODUCT, EVEN IF WELL TRAVELED LIVING OR ITS DIRECTORS, OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES, COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS, OR DAMAGES ARE FORESEEABLE. IN NO EVENT WILL WELL-TRAVELED LIVING OR ITS OFFICERS, DIRECTORS, OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES, COSTS, OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
-
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO THE PURCHASER.
EXTEND YOUR WARRANTY
When you purchase a Fire Sense or Balkene Home product from any authorized retailer, you’ll have peace of mind in knowing that it comes with a one-year warranty. Extend your warranty for an additional year when you review your item at balkenehome.com within 365 days of purchase.
Important Notice
Do NOT return to place of purchase—for customer service and warranty issues:
Call toll-free 866-985-7877| 9 am – 9
pm, EST
---|---
Email [email protected]|
Live Chat www.balkenehome.com | 9 am – 6 pm,
EST, Monday – Friday
Distributed by:
Well Traveled Living
716 S 8th Street, Amelia Island, FL 32034
balkenehome.com
[email protected]
866-985-7877
09302021
Fire Sense ®, Patio Sense, ® Avalon Home, ® Mojave Sun ®, Vulcan ®, Balkene Home ®, and Well Traveled Living ® are registered trademarks of Well Traveled Imports, Inc ®. All assembly instruction presentations are the property of Well Traveled Imports, Inc. ® and are protected by U.S. copyrights and trademarks. All rights reserved.
References
- BalkeneHome.com: Versatile Furnishings & Outdoor Heating – Fire Sense/Balkene Home
- BalkeneHome.com: Versatile Furnishings & Outdoor Heating – Fire Sense/Balkene Home