JUNO RB4 SWW5 RetroBasics 4 Inch Switchable White LED Instruction Manual

JUNO RB4 SWW5 RetroBasics 4 Inch Switchable White LED

Product Information

The Juno RetroBasicsTM LED trims can be used as retrofit trims for incandescent housings already installed in application or with dedicated quick connect housings by Juno.

Product Contents

Each unit carton contains the following: 1ea LED module, 1ea E26 adapter (Except L/SKTWHIP models). Check for all contents prior to installation.

Required Tools

Safety glasses and gloves are required for installation. They are not included in the kit.

Installation Instructions

1. Read and follow all safety instructions and save them for future reference.

2. Check the product contents prior to installation. Ensure that the trim kit is accepted as a component of a
   luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.

3. Product must be installed by a qualified electrician in accordance with the applicable and appropriate electrical codes.
   The installation guide does not supersede local or national regulations for electrical installation.

4. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

5. This device is not intended for use with emergency exits or emergency lighting.

6. If using trims provided with Torsion Spring Brackets (Models RB56, RB56S, and RB56SC Only), prepare for trim installation by following these steps:

   • Remove old trim if present and ensure that input power is 120V only.
   • The default setting of the torsion springs is for a 6 recessed housing. No adjustment is required if installing into a 6 housing.
   • If installing into a 5 recessed housing, loosen the (2) torsion spring bracket mounting screws on top of the retrofit module (Figure 1) to adjust the brackets and align with the 5 setting indicator visible on the trim. Once springs are in new position, tighten the torsion bracket mounting screws to securely to hold the brackets in place.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

Product Information: Juno RetroBasics™ LED trims may be used as retrofit trims for incandescent housings already installed in application or with dedicated quick connect housings by Juno.

Product Contents: Each unit carton contains the following: 1ea LED module, 1ea E26 adapter (Except L/SKTWHIP models). Check for all contents prior to installation.

Required Tools (not included): Safety glasses and gloves.

Product Listings: CSA certified to U.S. and Canadian safety standards; Energy Star qualified; wet location listed; and WSEC ASTM E283 for Air-Tight rated with IC housings. RB4/RB4S/RB4SC minimum lamp compartment 4 inches (102 mm)diameter by 4 inches (102 mm) tall or minimum lamp compartment 60.2 in³ (987 cm³). RB56/RB56S/RB56SCminimum lamp compartment 5 inches (127 mm) diameter by 5.7 inches (145 mm) tall or minimum lamp compartment119 in³ (1950cm³). Use only in open luminaires. Suitable for Type IC or Type Non-IC luminaires.
The trim kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. Product must be installed by a qualified electrician in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local or national regulations for electrical installation.

Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
This device is not intended for use with emergency exits or emergency lighting.

Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com. Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products.

LED IMPORTANT SAFETY INSTRUCTIONS

• To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts,
  cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.

• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

• Installation and service of luminaires should be performed by a qualified licensed electrician.

• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.

• It will occasionally be necessary to clean the outside of the refractor/lens/trim. Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. Refractor/lens/trim should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.

• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.

• Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.

• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired, or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.

WARNING RISK OF ELECTRIC SHOCK

• Disconnect or turn off power before installation or servicing.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any applicable local code requirements.
• All wiring connections should be capped with UL approved recognized wire connectors.

CAUTION RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.

WARNING RISK OF BURN

• Allow lamp/fixture to cool before handling. Do not touch enclosure or light source.
• Do not exceed maximum wattage marked on luminaire label.
• Follow all manufacturer’s warnings, recommendations, and restrictions for: driver type, burning position, mounting locations/methods, replacement and recycling.

CAUTION RISK OF FIRE

• Keep combustible and other materials that can burn, away from lamp/lens.
• Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.

CAUTION RISK OF PRODUCT DAMAGE

• Never connect components under load.

• Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.

• Never connect an LED product to an unapproved dimmer pack. Contact ABL directly for any dimmers not specifically recommended for the product.

• Unless individual product specifications deem otherwise: Allow for some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or conduction cooling.

• Unless individual product specifications deem otherwise: Maximum ambient temperature is 90°C.
  Do not operate fixture at temperatures higher than this.

• Unless individual product specifications deem otherwise: Never mount in places where fixture will be exposed to rain, high humidity, extreme temperature changes or restricted ventilation.

• LED products are Polarity Sensitive. Ensure proper Polarity before installation.

• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit.

• Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.

• There are no user serviceable parts inside the unit. Do not rewire, reconfigure, or modify the unit or attempt any repairs yourself. Additionally, field replacement of the LED assembly or lamps is not allowed by UL standards at this time. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative.

CAUTION RISK OF WIRING PRODUCT DAMAGE

To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

All luminaires that contain electronic devices that generate frequencies above 9kHz from any component within the luminaire comply with one of the following Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

Juno LED Trim Kit Compatibility in Recessed Cans

Juno LED Trim Kits are designed to work with most standard UL listed recessed incandescent housings. When used with standard medium base incandescent housings, the medium base socket adaptor must be used. Housing compatibility can be determined by measuring the recessed housing diameter and height as shown in the diagram. Refer to the chart for compatible size ranges. Housing construction features vary. The height and diameter chart should be used as a guideline. Actual installation is the best method of determining compatibility.

PREPARE FOR TRIM INSTALLATION

Trims provided with Torsion Spring Brackets (Models RB56, RB56S, and RB56SC Only)

1. Remove old trim if present. Ensure that input power is 120V only.
2. The default setting of the torsion springs is for a 6″ recessed housing. No adjustment is required if installing into a 6″ housing.
3. If installing into a 5″ recessed housing, loosen the (2) torsion spring bracket mounting screws on top of the retrofit module (Figure 1) to adjust the brackets and align with the 5″ setting indicator visible on the trim. Once springs are in new position, tighten the torsion bracket mounting screws to securely to hold the brackets in place.

Note: The RB56, RB56S, and RB56SC modules only install with the torsion springs, no other mounting clips are provided.

Trims Provided with Retention Spring Clips (Models RB4, RB4S, and RB4SC Only)

1. Remove old trim if present. Ensure that input power is 120V only.
   Note: The RB4, RB4S, and RB4SC modules only install with the retention springs, no other mounting clips are provided.

ELECTRICAL CONNECTION INSTRUCTIONS

1. For installation into existing housings with medium base sockets: Screw the E26 medium base socket adapter into the socket in the recessed housing (see Figure 2)

2. Plug the orange connector of E26 socket adapter into mating orange connector on
   the fixture module by pushing firmly to ensure connectors are securely fastened (see Figure 3).

3. Installation into dedicated quick connect housings: Plug the connector provided on the trim into the mating connector in the housing by pushing firmly to ensure connectors are securely fastened (See Figure 4).
   Note: No extra Grounding Connection Hardwire Kit is supplied with module.
   Note: Do not let the module hang unsupported by the orange connector.

COLOR TEMPERATURE ADJUSTMENT

Select desired CCT setting on trim – position switch to select LED color temperature of 2700K (warm), 3000K, 3500K, 4000K (cool) or 5000K (day light)
(model SWW5 only). (See Figure 5)

Note: Models RB4SC and RB56SC ONLY – LED Tunable White CCT settings are configured by the supported mobile apps: Amazon Alexa, Google Home, and SmartThings. See Quick Start Guide for pairing instructions.

INSTALLATION OF THE MODULE INTO THE RECESSED HOUSING:

Recommended: Use gloves to avoid transferring dirt and fingerprints to trim during installation.

1. For models with torsion springs (Models RB56, RB56S, and RB56SC Only): Squeeze each torsion spring together and seat them inside the housing torsion brackets. Release springs, and gently push module into housing until flush with ceiling (Figure 6).
2. For models with spring retention clips (Model RB4, RB4S, and RB4SC Only): Center the LED module in the housing opening and gently push the module up into the housing evenly on all sides (Figure 7) until flush with ceiling
   (Figure 8).

NOTE:

• Align the two retention clips with the recessed housing avoiding interference with anything protruding from the housing walls.
• For removal of a recessed LED module with retention clips, pull down and rotate back and forth until free. If needed, the use of a flat blade screwdriver to release the clips from the recessed housing may aid in the removal process.

RECOMMENDED DIMMING SWITCHES (Model SWW5 only):
The LED Modules are compatible with several standard residential dimmers. A list of recommended dimmers can be found at www.acuitybrands.com, keyword search RB4/RB4S or RB56/RB56S. Exclusion from the list does not mean a dimmer will not work in conjunction with your LED module. Consult with your dimmer manufacturer regarding compatibility with LED modules/lamps.

Note: Models RB4SC and RB56SC ONLY – Cannot wire with any wall dimmers, dimming setting can be configured via supported mobile apps.

One Lithonia Way · Conyers, GA 30012 · Phone 1-(800)705-7378 Visit us at www.acuitybrands.com/juno-recessed
© 2022 Acuity Brands Lighting, Inc.

References

• Acuity Brands | Lighting, Controls, and Building Management Solutions
• Juno® | Better by Design™
• U.S. Environmental Protection Agency | US EPA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>