JUNO WF4CTUWH90CRIMWM6 4 in. Contractor Select Tunable Canless Regressed Integrated LED Matte Instruction Manual
- June 5, 2024
- Juno
Table of Contents
JUNO WF4CTUWH90CRIMWM6 4 in. Contractor Select Tunable Canless Regressed
Integrated LED Matte
INSTALLATION INSTRUCTIONS
WARNING: For your safety, read and understand instructions completely
before starting installation. Before wiring to power supply, turn off
electricity at the fuse or circuit breaker box.
NOTE: Juno products are designed to meet the latest NEC requirements and
are classified in compliance with applicable UL standards. Before attempting
installation of any recessed lighting product, check your local electrical
building code. This code sets the wiring standards and installation
requirements for your locality and should be understood before starting work.
SAVE THESE INSTRUCTIONS
Product Information
The round 4″ and 6″ Juno Smart WaferTM downlight provides high-quality light
output and efficiency while eliminating the need for recessed housings. The
innovative, slim design allows for easy retrofit, remodel or new construction
installation from below the ceiling. Connects from any Apple or Android phone
to the Juno Smart WaferTM directly using Bluetooth® and free download of the
SmartThings® App.
The Juno Smart WaferTM downlight consists of the following: LED module, remote
driver box and installation instructions. Check for all contents prior to
installation.
Optional Items: New Construction Plate, Joist Bar Kit, and Extension Cable
(6ft, 10ft, and 20ft) see www.acuitybrands.com
for more details.
Do not make or alter any open holes in an enclosure of wiring or electrical
components during kit installation.
WARNING – Risk of fire or electric shock.
- Do not alter, relocate, or remove wiring, lampholders, power supply, or any other electrical component.
- Installation of this retrofit assembly requires a person familiar with the construction and operation of the luminaire’s electrical system and the hazard involved. If not qualified, do not attempt installation. Contact qualified electrician.
- Install this kit only in luminaires that have the construction features and dimensions described in these instructions, and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to
edges of sheet metal or other sharp objects.
THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE
SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR AUTHORITIES
HAVING JURISDICTION.
FCC Supplier’s Declaration of Conformity
Juno WF4C RD/REG/ADJ TUWH MW and WF6C RD/REG/ADJ TUWH MW. This device complies
with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Suppliers Name: Acuity Brands Lighting, Inc.
Suppliers Address (USA): One Lithonia Way | Conyers, GA 30010
Suppliers phone number: 800.323.5068
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the device.
Note: This device has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This device generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or
television reception, which can be determined by turning the device off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This device should be installed and operated with a
minimum distance of 20cm between the radiator and any part of your body.
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF RADIATION EXPOSURE STATEMENT: This device complies with FCC and ISED
RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This device should be installed and operated with a minimum distance of 20cm
between the device and any part of the user’s body.
Only for 5G Devices
The devices for the band 5150-5350 MHz are only for indoor use.
Note: Before beginning the installation
- A. Make sure all power is off, shutting power off in breaker box to areas where downlights are to be installed is recommended.
- B. Load the Samsung SmartThings® App to your Android or iOS mobile device.
Required Tools (not included): Safety glasses and gloves.
-
Double check and measure the ceiling hole. Make sure it is the correct size for outside rim of the luminaire to cover the hole while still allowing the back of luminaire to sink in to the ceiling and springs to hold firmly.
Remove existing retrofit can if present or move it out of the way since it will not be needed for installation.
If new hole is to be cut, use provided hole template. Place template over the desired location. Trace the outer ring with a pen or pencil (not included). Cut the opening with a saw (not included).(Figure 1) -
Open the cover of the remote driver box. Push and remove one of the knockouts on the side plate.
- Locate power supply leads from remote driver box and connect to power source using wago connectors (provided).
- Connect black wire to live wire, white wire to neutral wire, and green wire with ground (as shown) and secure using connector. Close the cover of the box. (Figure 2)
-
Connect the remote driver box to the light fixture and tighten the nut connector by hand. Arrow on the male and female parts of the connector between the driver and fixture cable should match. (Figure 3)
-
Place remote driver box thru the cut-out hole.
- MUST follow local electric code for rigid attachment and placement of the remote driver box. (Figure 4)
-
Pull the spring clip on the fixture up and through the ceiling hole and place module in the hole making sure the spring clips are holding securely.
(Figure 5)
-
Turn the power back on. If the mod-ule doesn’t illuminate within 5 seconds, turn power off, carefully remove the module and double check all wiring and replace. (Figure 6) WARNING: DO NOT PLACE YOUR HAND UNDERNEATH SPRING CLIP DURING REMOVAL PROCESS. SNAPPING OF THE CLIPS CAN CAUSE INJURIES TO THE HAND. (Figure 7)
* DO NOT USE ANY OTHER DRIVER EXCEPT THE JUNO DRIVER THAT IS INCLUDED WITH THE FIXTURE.
* DO NOT CONNECT MULTIPLE MODULES TO ONE DRIVER.
* DO NOT OPEN THE MODULE AND SIDE PLATE OF THE REMOTE DRIVER BOX – NO SERVICEABLE PARTS INSIDE.- Once the fixture is operational, activate the app on your mobile control device, and follow the instructions listed in the QUICK START GUIDE.
Trouble Shooting Guide
If this fixture fails to operate properly, use the guide below to diagnose and correct the problem.
- Verify that fixture is wired properly.
- Verify that fixture is grounded correctly.
- Verify that the line voltage at the fixture is correct.
If further assistance is required for installation issues, contact: Technical
Support at: (800) 705-SERV (7378).
For setup support using the Samsung SmartThings® App. contact technical
support at: 800-726-7864
This LED module does not require service or new bulbs to change.
WARRANTY
Limited warranty located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Technical Services Phone (800) 705-SERV (7378)
Optional Mounting Kits: Instruction sheet for new construction plate and joist bar kit can be found at www.acuitybrands.com
One Lithonia Way, Conyers, GA 30012 • Phone: (800) 705-SERV (7378) • Visit us at www.acuitybrands.com ©2022 Acuity Brands Lighting, Inc Rev 03/22
References
- Acuity Brands | Lighting, Controls, and Building Management Solutions
- Acuity Brands | Lighting, Controls, and Building Management Solutions