Jandy R0441900 Handheld Remote Control Outdoor Transceiver J-Box Installation Guide

Jandy R0441900 Handheld Remote Control Outdoor Transceiver J-Box Installation Guide

These instructions are to be used with the following Jandy Replacement Kits:

R0441900– Handheld Remote Control Transceiver J-Box Replacement Kit
R0686300– Handheld Remote Control Transceiver 18 Channel J-Box Replacement Kit
R0443300– Handheld Remote Control Transceiver J-Box Hardware Replacement Kit

WARNING

FOR YOUR SAFETY – This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exist. The maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in this manual can be followed exactly. Before installing this product, read and follow all warning notices and instructions that accompany this product. Failure to follow warning notices and instructions may result in property damage, personal injury, or death. Improper installation and/or operation may void the warranty

Improper installation and/or operation can create unwanted electrical hazard which may cause serious injury, property damage, or death.

ATTENTION INSTALLER – This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner/operator of this equipment.

FCC Regulatory Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This device must be installed to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter product guidelines.

CAUTION: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

This device must be installed to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.

ISED Canada

Regulatory Compliance Statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Important Safety Instructions

READ AND FOLLOW ALL INSTRUCTIONS

WARNING

FOR YOUR SAFETY – This product must be installed and serviced by a professional pool/spa service technician. The procedures in this instruction sheet must be followed exactly. Ensure that all electrical power to the system is turned off before approaching, inspecting or troubleshooting any leaking valves that may have caused other electrical devices in the surrounding area to get wet. Failure to do so could result in an electrical hazard which could result in death or serious injury due to electrical shock, and may also cause damage to property and/or operation will void the warranty.

CAUTION

ESD Precautions – Electrostatic discharge (ESD) events can harm electronic components inside your device. To prevent ESD damage, you should discharge static electricity from your body before you interact with any of your devices internal electronic components, such as a printed circuit board (PCB) or any connection terminals. You can also take the following steps to prevent damage from electrostatic discharge:

• When unpacking a static-sensitive component from its shipping carton, do not remove the component from the antistatic packing material until you are ready to install the component. Just before unwrapping the antistatic package, be sure to discharge static electricity from your body.
• When transporting a sensitive component, first place it in an antistatic container or packaging.

WARNING

Risk of Electric Shock which can result in Serious Injury or Death.

Before attempting installation or service, ensure that all power to the circuit supplying power to the system is disconnected or turned off at the circuit breaker.

All wiring must be done in accordance with the National Electric Code (NEC), NFPA-70. In Canada, the Canadian Electrical Code (CEC), CSA C22.1, must be followed. All applicable local installation codes and regulations must be followed.

This document gives instructions for replacing the Jandy Handheld Remote Control Transceiver J-Box assembly, gasket, and screws. These instructions must be followed exactly. Read through the instructions completely before starting the procedure. Please save these instructions.

To identify the parts that are included in your kit, refer to the parts list and exploded view located on page 2 of this manual. If any parts are missing from the kit please call your local Jandy distributor for assistance. For technical assistance please contact our Technical Service Department at 800-822-7933.

SAVE THESE INSTRUCTIONS

Remove Existing Transceiver J-Box Assembly

1.  Turn off all power to the power center.

2. Open the door to the power center and remove the dead panel.

3. Disconnect the red four-pin connector from the red terminal bar located on the power center PCB (see Figure 1).
   
   Figure 1. Transceiver J-Box Installation

4. Disconnect the four conductor wire from the red four-pin connector. Set aside the red four-pin connector.

5. Carefully, pull the four conductor wire through the low voltage raceway and out of the power center.

6. On the transceiver J-Box, remove the existing two (2) screws that secure the J-Box to the mounting surface. Then, remove the transceiver J-Box from the mounting surface.

Install New Transceiver J-Box Assembly

1. Remove the new transceiver J-Box assembly from the packaging.

2. Remove the two (2) new mounting screws from the packaging.

3. Using the existing mounting holes and the new mounting screws, secure the new transceiver J-Box to the mounting surface.
   NOTE: For optimal performance, ensure that the transceiver J-Box is mounted at least 6 feet above the ground, and 8 feet from brush-type motors such as blowers, which can cause interference.

4. Feed the four conductor wire into the power center through the low voltage raceway.

5. Connect the four conductor wire to the red fourpin connector that was set aside in the Remove Existing Transceiver section.

6. Connect the red four-pin connector to the red terminal bar on the power center PCB.

7. Install the dead panel to the power center and restore all power.

Replace Existing Transceiver J-Box Hardware

WARNING

Risk of Electric Shock which can result in Serious Injury or Death. Before attempting installation or service, ensure that all power to the circuit supplying power to the system is disconnected or turned off at the circuit breaker.

All wiring must be done in accordance with the National Electric Code (NEC), NFPA-70. In Canada, the Canadian Electrical Code (CEC), CSA C22.1, must be followed. All applicable local installation codes and regulations must be followed.

NOTE: Use the following procedure only if replacing the transceiver J-Box hardware with Jandy part number R0443300.

1. Turn off all power to the power center.

2. Remove the existing two (2) screws that secure the cover to the transceiver J-Box (see Figure 2). Remove the cover.

3. Remove the existing gasket from the transceiver J-Box.
   NOTE: The gasket may have adhered to the cover removed in Step 2.

4. Remove the new gasket from the packaging. Place the gasket on the transceiver J-Box housing. When placing the gasket, ensure that the holes punched out in the gasket line up with the screw holes on the transceiver J-Box housing.

5. Remove the new cover from the packaging.

6. Remove the two (2) new screws from the packaging.

7. Using the new screws, secure the new cover to the transceiver J-Box housing.

8. Restore power to the system.

Replacement Kits Parts List and Exploded View

![Parts

List](https://manuals.plus/wp-content/uploads/2023/05/Screenshot_5-36.png)
Figure 2. Transceiver J-Box Exploded View

Zodiac Pool Systems LLC
2882 Whiptail Loop # 100 Carlsbad, CA 92010, USA Jandy.com | 1.800.822.7933 Zodiac Pool Systems Canada, Inc. 2-3365 Mainway Burlington, ON L7M 1A6, Canada Jandy.ca | 1.800.822.7933
A Fluidra Brand
©2022 Zodiac Pool Systems LLC. All rights reserved. ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license. All other trademarks are the property of their respective owners. H0572700_REVE

(FRENCH TRANSLATION OF FULL MANUAL PENDING)

Documents / Resources

| Jandy R0441900 Handheld Remote Control Outdoor Transceiver J-Box [pdf] Installation Guide
R0441900, R0686300, R0443300, R0441900 Handheld Remote Control Outdoor Transceiver J-Box, Handheld Remote Control Outdoor Transceiver J-Box, Remote Control Outdoor Transceiver J-Box, Outdoor Transceiver J-Box, J-Box
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>