BG ELECTRICAL PCDSB20B-01 Shaver Sockets Instruction Manual
- June 11, 2024
- BG Electrical
Table of Contents
BG ELECTRICAL PCDSB20B-01 Shaver Sockets
Product Information
This product is a handheld vacuum cleaner designed for quick and easy cleaning of small messes and spills. It comes with a rechargeable battery and a washable filter. The vacuum has a crevice tool attachment for hard-to-reach areas and a dusting brush attachment for delicate surfaces.
Product Usage Instructions
- Charge the vacuum before first use by plugging it into a power source using the included charging cable. The charging indicator light will turn on and turn off when fully charged.
- Attach the desired accessory to the vacuum by pressing it firmly onto the end of the nozzle.
- To turn on the vacuum, press and hold the power button located on the handle. Release the button to turn off the vacuum.
- To empty the dustbin, remove it from the vacuum by pressing the release button and pulling it out. Empty the contents into a trash can and replace the dustbin.
- To clean the filter, remove it from the dustbin and wash it with water. Allow it to fully dry before replacing it.
- For best performance, avoid picking up large or heavy debris and use the vacuum on small messes and spills.
Wiring Instructions
Power Off
Before fuse box. commencing work always isolate the power at the consumer unit
top *Note and – If bottom your lugs installation or bend uses fully a back.
four-lug metal mounting box, remove the
Replacing an existing accessory
- Note Unscrew the cable accessory connections: from the wall/mounting box.
- The illustration shows 1 wire of each color etween connected the to mounting each box terminal. earth
- Their terminal should and be the an accessory additional earth connection terminal. b
- Unscrew each terminal to release the wire.
New installation
-
mounting, Install mounting ensuring box appropriate (metal or size of molded) product for either [Mounting flush or box to surface be
-
purchased Select the most separately]. the suitable entry point of the mounting box [knock-out] and
If a route metal the box cables is used, through. a cable grommet should be fitted to the entry point. -
terminals. Cables should be prepared so a sufficient conductor length reaches the
to Strip enter the ends terminals. of the individual conductors leaving an adequate length bare
Complete Installation & Test
- wires Carefully are trapped position between the accessory plate into and the wall mounting and box, secure ensuring with that screws no
- do To not prevent over tighten] moisture then from insert entering screw the covers socket, [optional]. due to the formation of mounting condensation and on the socket walls, with it is a suitable recommended waterproof to fill any sealant. gaps between the
- reset Once MCB the [trip], installation switch has the been power back completed on at the correctly, consumer replace unit the and fuse/ test.
Safety Warning
For Building your safety, Regulations. this If a product in any must doubt, be
or installed where in required accordance by the with law, local consult
cation a scheme. competent Further person who information is registered is
available with an on line or electrical from your self-certifiLocal Please
Authority. read carefully and use in accordance with these safety wiring
switched instructions. off at Before the mains. commencing Either by any
switching the electrical off work the ensure consumer the unit supply or by is
removing in accordance with the appropriate latest fuse edition or of turning
the IET off MCB regulations [trip]. [BS Wiring 7671]. should be in To
application. To prevent fire hazards always use cable of the correct rating &
type for the
Warning do not exceed the load rating of this device as stated on the rear of
the product.
Wire Identification – Twin & Earth Cable wNeortee -inAtrso frame d1.s t April
2004 new colour codes for hard-wire installations
Product Markings
Additional Advice for Decorative Products
Fixing method varies depending on which product range is supplied. Always
ensure wall surface is reasonably flat and smooth, with no bumps or
projections. Metal front plates WITH screw fixing holes, fix the unit to the
back box using two fixing screws supplied. All Decorative products MUST have an
earth connection between the front plate and back box. Frontplates WITHOUT
screw fixing holes. These products comprise main unit with an integral gasket
and front plate as a separate item. Fix unit to back box using two fixing
screws supplied. Clip the front plate onto main assembly, ensuring the
screwdriver notch is located bottom right-hand corner.
To remove plate, place medium size flat bladed screwdriver in the notch and
lever off against gasket.
Technical
- Voltage : 220-240V ac
- Frequency: 50/60Hz
- Output : 115VAC 20VA/240VAC 20VA
- Terminal capacity: 3 x 2.5mm’ 2 x 4mm’
- Min box depth : 47mm
- The transformer of the shaver socket is a non-inherently short circuit-proof safety isolating transformer.
This shaver socket is for indoor use only.
ASTA Approved
The ASTA quality mark is evidence that the product has been independently
tested to comply with the relevant clauses of the applicable standards.
Care
To maintain the high-quality appearance of decorative finish switches and sockets, BG Electrical recommends the use of a soft cloth periodically to clean the front face. When installing a decorative product please ensure that the wall is decorated, finished and free of moisture prior to installation. BG Electrical recommends avoiding using, but not restricted to, these substances from becoming in contact with the decorative metal front-plates when cleaning or decorating:
- Adhesive tape, including low-tack masking tape
- Solvents
- White spirit
- Multi-surface cleaners
- Industrial multipurpose cleaning wipes
- Wet wipes Using items like those listed above may cause a degrading effect to the front-plates lacquer/plated finish, although the function will remain
unaffected.
Adress Helpline
If you have further technical assistance you can get in touch with our
Technical Helpline on:
+44 (0)3300 249 279
technical.support@bgelectrical.co.uk
Environmental Protection
This symbol is known as the “Crossed-out Wheelie Bin Symbol””. When this symbol is marked on a product or battery, it means that it should not be disposed of with your general household waste. Some chemicals contained within electrical/ electronic products or batteries can be harmful to health and the environment. Only dispose of electrical/electronic/ battery items in separate collection schemes, which cater for the recovery and recycling of materials contained within. Your co-operation is vital to ensure the success of these schemes and for the protection of the environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>