Kosnic RYD30-W40 Alden I Backlit LED Panel Installation Guide
- June 9, 2024
- Kosnic
Table of Contents
- Kosnic RYD30-W40 Alden I Backlit LED Panel
- Product Information
- Product Usage Instructions
- LED Panel Installation
- Safety Information
- Optional Gears and Accessories Information
- Light Source Information
- INSTALLATION INSTRUCTION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Kosnic RYD30-W40 Alden I Backlit LED Panel
Product Information
LED Panel Installation
The LED Panel Installation is available in various models such as
RYD30-W40, ALD30-W30, ALD1206-W30, ALD20-W40, ALD30-W40, ALD1206-W40,
ALD28-W40, ALD30-W65, and ALD1206-W65. The product comes with safety
instructions and is rated for indoor use only with an Earth connection through
a terminal marked E. The light source of the product is defined as the LED
module and backplate of the product itself. The energy class of the light
source varies from D to E depending on the model.
Product Usage Instructions
LED Panel Installation
- Before use, please read the safety instructions provided in the user manual thoroughly and retain it for future reference.
- Ensure that the product is installed in compliance with national building and wiring regulations.
- If you are unsure about installing the product, consult a qualified electrician.
- For maintenance purposes, turn off and isolate the circuit to be worked on by removing the fuse or switching the circuit breaker off at the distribution board.
- The LED Panel Installation requires an Earth connection through a terminal marked E for Earth continuity.
- Disassembly and disposal of the product at the end of its life should be done using commonly available tools. If in doubt, please contact Kosnic.
LED Panel Installation
Please read these instructions thoroughly before use and retain for future reference.
Safety Information
- Installation must be carried out in accordance with national building and wiring regulations. If you are in any doubt about installing this product, please consult a qualified electrician.
- Before commencing installation or any maintenance, turn off and isolate the circuit to be worked on by removing the fuse or switching the circuit breaker off at the distribution board.
- This product is suitable for connection to a 220- 240Vac 50/60Hz supply.
- The drivers are a class II product not requiring an Earth connection though a terminal marked E is provided for Earth continuity and are IP20 rated for indoor use only.
- The panels are a class III product and are IP20 rated unless otherwise indicated (IP44 when ceiling recess mounted).
Optional Gears and Accessories Information
- The LED panels are compatible with the optional emergency modules which can power the panels at a reduced output in the event of a power failure. Please refer to instructions included with the emergency modules for installation.
- Alternative drivers may be available for dimming the panels. Please refer to alternative driver instructions for additional wiring requirements.
- The LED panels also can be flush mounted or suspended. Please refer to instructions included with the accessories for installation. The installer should be aware that there are external drivers that need to be accommodated.
Light Source Information
- ALD20-W40, ALD28-W40 contains a light source of energy class D.
- RYD30-W40, ALD30-W30 , ALD30-W40, ALD30-W65, ALD1206-W30, ALD1206-W40, ALD1206-W65 contain a light source of energy class E.
The light source is defined as the LED module and backplate of the product itself.
Notes for disassembly and disposal at end of product life:
At the end of product life, the product should be disconnected from the mains
supply by a suitably qualified person and dismantled into its constituent
parts prior to disposal. Only commonly available tools such as screwdrivers,
knives, soldering irons, spanners, pliers etc should be used and appropriate
safety measures taken during their use. Parts such as LED strips, LED panels,
electrical control gear, wiring, plastic diffusers, metal components such as
back plates or heatsinks should all be separated from the product and disposed
of via appropriate waste streams. Please consult your local authority for WEEE
recycling and disposal options. List of commonly available tools is not
comprehensive, if in any doubt please contact Kosnic.
INSTALLATION INSTRUCTION
Kosnic Lighting Ltd, Unit 2, Kennetside, Bone Lane, Newbury, RG14 5PX, UK The Waste Electrical & Electronic Equipment Regulations (WEEE) require that products bearing this symbol must not be disposed of with household waste as they may contain substances harmful to the environment. The Local Authority can provide advice on recycling.
Products Covered:
- RYD30-W40 ALD30-W30 ALD1206-W30
- ALD20-W40 ALD30-W40 ALD1206-W40
- ALD28-W40 ALD30-W65 ALD1206-W65
References
- Kosnic: New age of lighting - Designers and manufacturers in LED Lighting
- Kosnic: New age of lighting - Designers and manufacturers in LED Lighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>