Harbor Breeze 724 Indoor Ceiling Fan with Light Kit User Manual

: June 9, 2024
: Harbor Breeze

Table of Contents

Harbor Breeze 724 Indoor Ceiling Fan with Light Kit
SAFETY PRECAUTIONS
SAFETY WARNINGS
ASSEMBLY INSTRUCTIONS
OPERATING INSTRUCTIONS
CARE AND MAINTENANCE
FAQs
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Harbor Breeze 724 Indoor Ceiling Fan with Light Kit

SAFETY PRECAUTIONS

Please observe the following general safety precautions carefully before and during all phases of handling, installation, removal, operation, and maintenance of this product. Failure to comply with these precautions violates the safety standards of the design, manufacture, and intended use of the product. We assume no liability for the customer’s failure to comply with these requirements.

SAFETY WARNINGS

Read all instructions and safety information. Review the assembly diagrams provided before installing your new ceiling fan.
This remote controller must be installed according to local authority regulations.
This product is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
Young children should be supervised to ensure that they do not play with the appliance.
All electrical works must only be undertaken after disconnection of the power by removing fuses or turning off the circuit breaker, to ensure all pole isolation of the electrical supply.
Do not use it outdoors where it could be exposed to water or moisture.
This product is for indoor use only.
This product is to be used only for controlling a ceiling fan with an A.C. (Alternating Current) motor.
Do not pull or cut short lead wires.
Do not drop or bump the remote controller set.
Do not use this remote controller in conjunction with any variable (rheostat) wall controller.
Do not use the remote control transmitter (handset) with any other receiver.
Keep the battery out of reach of children.
This manual is not intended to instruct or assist untrained or unqualified persons to install this remote controller.
It is the responsibility of a qualified, licensed installer and user to apply common sense and care at all times during installation and operation.

ASSEMBLY INSTRUCTIONS

Attach mounting plate (A) to outlet box (not included) using two screws (not included). Securely tighten two outlet box screws. Pull black, white, and grounded wires out of the outlet box and through the hole in the mounting plate (A).
Place trim ring (C) over the canopy, and lay it on 2 fan motors (B).
Loosen two preassembled screws across from each other on the mounting plate (A). Remove and save the remaining two preassembled screws. Hang fan motor (B) on the mounting plate (A) hook using one of the non-slotted holes in the canopy.
IMPORTANT : Do NOT use this fan with a dimmer switch or variable speed wall control. Using a dimmer switch or variable speed wall control will damage the fan.
Connect the BLACK wire from the fan to the BLACK wire from the ceiling. Connect the WHITE wire from the fan to the WHITE wire from the ceiling. Connect all GROUND (GREEN) wires from the fan together to the GREEN/BARE wire from the ceiling. Connecting the GREEN/GROUND wires is conducive to receiving the signal of the remote control.
NOTE: The BLACK wire is the hot power for the fan and light kit. The WHITE wire is common for fan and light kits. GREEN wire is the ground wire. lf the household wires are different colors than those referred to above, stop immediately and consult a professional electrician to determine proper wiring.
Twist wire ends together and screw wire connectors (AA) in a clockwise direction. Tape wire connectors (AA) and wires together with electrical tape (not included).
Hardware Used
Align keyhole slots on the fan motor (B) with the protruding screw heads on the mounting plate (A). Lift the fan motor (B) up to the mounting plate (A), making sure not to break any wire connections. Rotate the fan motor (B) clockwise until the screw heads fully engage into keyhole slots. Insert the previously removed screws (Step 3, page 6) and securely tighten all the screws.
Align the notches on the fan motor (B) canopy with raised areas inside the trim ring (C). Pop the trim ring (C) into the canopy.
Remove and discard preassembled rubber shipping stabilizer tabs (I) from fan motor (B). Insert blade (D) into the slot on fan motor (B). Secure blade (D) with three-blade screws (BB). Repeat for remaining blades (D) and blade screws (BB).
Hardware Used
Loosen two screws from the switch housing plate (H). Remove and save the remaining screw.
Connect the 9-pin plug exiting the bottom of the fan motor (B) to the 9-pin plug from the light plate (E). Be sure the plugs snap together completely. Attach light plate (E) to switch housing plate (H). Align keyholes, then twist to lock. Replace the previously removed screw (Step 9) and securely tighten all screws.
Loosen two preassembled screws from light plate (E). Remove and save the remaining preassembled screw from the light plate (E).
Connect the WHITE wire from the light plate (E) to the WHITE wire from the light fixture (F). Connect the BLUE wire from the light plate (E) to the BLUE wire from the light fixture (F). Align the keyhole slots on the light fixture and the light plate (E), and twist to lock. Replace the previously removed screw (Step 11, page

and securely tighten all of the screws.

Align the three flat areas on the top flange of the glass (G) with the three raised dimples in the light fixture (F). Insert the glass (G) into the light fixture (F), then turn the glass (G) clockwise until it stops.
CAUTION: Avoid touching the LED with your bare hands. Be sure the power is off and the glass and LED are cool before cleaning the fixture.
OPTIONAL: If desired, the wall bracket in the remote pack (J) can be installed to house the remote control. Remove the small plate preassembled on the wall bracket and use the screws in the remote pack (J) to secure the wall bracket at the desired mounting location. Replace the small plate, then rest the remote control from the remote pack (J) into the wall bracket.

OPERATING INSTRUCTIONS

REMOTE CONTROL

NOTE: If you have more than one remote-controlled fan installed in the same location, you may want to change the frequency of the remote control to avoid any possible interference between remote controls. To change the frequency of the remote control, change the dip switch settings as described below:

Install Battery/Learning Process:
Remove the battery cover from the back of the remote found in the remote pack (J). Insert the battery from the remote pack (J) into the remote; ensure the polarity of the battery matches the polarity indicated in the battery compartment — positive (+) to positive (+) and negative (-) to negative (-). Replace the battery cover.
If you need to change the dip switches in the remote control due to a potential interference issue, slide the dip switches to your choice of either up or down — the factory setting is up. Within 30 seconds of turning the fan’s power on, press and hold the “Learn” button on the remote control for 1 second. Once the receiver has detected the set frequency, the light of the fan will blink twice. Replace the battery cover. To confirm the remote control and receiver have paired successfully press any of the fan speed control buttons on the remote control.
Fan Speed Control/Dimmer:
Low speed
Medium speed
High speed
Turns fan off
Turns light on or off
NOTE: For the DIMMER function, press and hold the light button. Light will dim. Release the button when the light is at the desired level.
NOTE: This remote control has a memory function. The receiver stores the fan speed and light setting when the fan is turned off. When fan is turned on again, it starts with the most recent settings.
Reverse Switch:
When the season changes, you may want to change the direction the fan blades spin. To switch between clockwise and counterclockwise rotation, flip the fan reversal switch.
WARNING: Wait for a fan to stop before reversing the switch.
- In warmer weather, counterclockwise rotation creates a downward airflow, which cools the air. Push the switch LEFT and see a Sun icon.
- In cooler weather, clockwise rotation creates an upward airflow, which moves hot air from the ceiling into the room. Push the switch RIGHT and see a Snowflake icon.

CARE AND MAINTENANCE

IMPORTANT: Shut off the main power supply before beginning any maintenance.
Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning.
At least twice a year, tighten all screws and lower canopy to check mounting bracket screws and downrod assembly.
Clean fan housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to the blades for added protection.
The total fixture wattage is 17.5 watts; do not attempt to replace LEDs.
Battery replacement: Use an A23 12-volt alkaline battery for the remote control.

FAQs

What is the size of the Harbor Breeze Indoor Ceiling Fan?****

The size of the Harbor Breeze Indoor Ceiling Fan varies depending on the specific model, but they typically range from 42 inches to 72 inches in diameter.

What is the maximum air flow rate of the fan?****

The maximum airflow rate of the fan varies depending on the specific model, but it can range from 2,000 to 6,000 cubic feet per minute.

What type of motor does the fan have?****

The fan typically has a powerful AC motor.

Can the fan be used in outdoor spaces?****

No, the fan is designed for indoor use only.

How many speeds does the fan have?****

The fan typically has three to six different speed settings.

Can the fan be operated by remote control?****

Yes, many models of the Harbor Breeze Indoor Ceiling Fan come with a remote control for easy operation.

Can the fan be mounted on a sloped ceiling?****

Yes, the fan can be mounted on a sloped ceiling with the use of a special mounting kit.