SJE RHOMBUS VERTICALMASTER Pump Switch Instruction Manual

: June 9, 2024
: SJE RHOMBUS

Table of Contents

SJE RHOMBUS VERTICALMASTER Pump Switch
Product Information
Product Usage Instructions
SJE VERTICALMASTER® PUMP SWITCH
ELECTRICAL WARNINGS
PREVENTATIVE MAINTENANCE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SJE RHOMBUS VERTICALMASTER Pump Switch

Product Information

The product is an electrical pump switch designed for pump down applications only. It is rated for Horsepower (HP) loads and is not suitable for control (pilot duty) applications. The switch should be installed and serviced by a qualified service person according to applicable electrical and plumbing codes. The product must be installed in accordance with National Electric Code, ANSI/NFPA 70 to prevent moisture from entering or accumulating within boxes, conduit bodies, fittings, float housing, or cable. The product should not be used with flammable liquids and should not be installed in hazardous locations as defined by National Electrical Code, ANSI/NFPA 70.

Product Usage Instructions

Determine the location for the pump switch.
Secure the pump switch to the discharge pipe by inserting the hose clamp through the mounting bracket slots and tightening the hose clamp.
Adjust the pumping range by adjusting the lift rod stop pin, lift rod, float, and float stop (grommet).
For units without plugs, connect wires as shown.

In 230 VAC installations, one side of the line going to the load is always HOT. This condition exists if the switch is on or off. Install a double pole disconnect on all 230 VAC circuits. Ensure cable connections are performed in a dry junction box or other watertight seal that seals both conductors and cable jacket. Failure to do so could result in electrical shock hazard and/or water traveling down the cable and entering the switch, affecting switch performance. It is important to replace the product immediately if any damage is found or suspected. The product must be installed in accordance with National Electric Code, ANSI/NFPA 70 so as to prevent moisture from entering or accumulating within boxes, conduit bodies, fittings, float housing, or cable. For technical support, contact +1 800-746-6287 or techsupport@sjeinc.com. Keep these instructions with warranty after installation. Products returned must be cleaned, sanitized, or decontaminated as necessary prior to shipment to ensure that employees will not be exposed to health hazards in handling said material. All applicable laws and regulations shall apply.

SJE VERTICALMASTER® PUMP SWITCH

This mechanically activated pump switch is designed for direct control of pumps in non-potable water and sewage applications. It works well in applications with limited space such as: small sump chambers, effluent applications, and laundry trays, as well as in large tanks. The SJE VerticalMaster® pump switch is not sensitive to turbulence. It is available for pump down applications only.

ELECTRICAL WARNINGS

ELECTRICAL SHOCK HAZARD
Disconnect power before installing or servicing this product. A qualified service person must install and service this product according to applicable electrical and plumbing codes.

EXPLOSION OR FIRE HAZARD
Do not use this product with flammable liquids. Do not install in hazardous locations as defined by National Electrical Code, ANSI/NFPA 70.

Failure to follow these precautions could result in serious injury or death. Replace product immediately if switch or cable becomes damaged or cracked. Keep these instructions with warranty after installation. This product must be installed in accordance with National Electric Code, ANSI/NFPA 70 so as to prevent moisture from entering or accumulating within boxes, conduit bodies, fittings, float housing, or cable

For detailed specifications on this product, or for the complete line of SJE Rhombus® panel, alarm, and switch products, visit our website at www.sjerhombus.com

A Pump Switch is designed for Horsepower (HP) rated loads and is not suitable for control (pilot duty) applications. It will fail prematurely when switching loads less than 1 Amp at 120 VAC. Select a float switch from our Control Switch offering for control applications..

PREVENTATIVE MAINTENANCE

Periodically inspect the product. Check that the cable has not become worn or that the housing has not been damaged so as to impair the protection of the product. Replace the product immediately if any damage is found or suspected.
Periodically check to see that the float and rod are free to move and operate the switch.
Use only SJE Rhombus® replacement parts.

NOTICE!
Products returned must be cleaned, sanitized, or decontaminated as necessary prior to shipment to ensure that employees will not be exposed to health hazards in handling said material. All applicable laws and regulations shall apply.

Determine location for pump switch
Secure pump switch to discharge pipe by inserting the hose clamp thru the mounting bracket slots and tightening the hose clamp.
Adjust pumping range
For units without plugs, connect wires as shown

WARNING
In 230 VAC installations, one side of the line going to the load is always HOT. This condition exists if the switch is on or off . Install double pole disconnect on all 230 VAC circuits. Ensure cable connections are performed in a dry junction box or other watertight seal that seals both conductors and cable jacket. Failure to do so could result in electrical shock hazard and/or water traveling down cable and entering the switch. Failure to guard against this may aff ect switch performance.