AOVX GX100 Goods Tracker User Guide

June 9, 2024
AOVX

AOVX GX100 Goods Tracker

AOVX GX100 Goods Tracker

Revision Date Author Description
V1.0 2021/11/119 YUKI Initial
V1.1 2022/01/10 YUKI Upgrade Platform
V1.2 2022/01/25 YUKI Upgrade LED indications
V2.0 2022/04/06 YUKI Upgrade layout

Introduction

Device overview

Figure_1 Overview of GX100

Device overview

Main functions

Light Monitoring Technology

24H real-time monitoring and recording the change of light. When an asset is abnormally unboxed, it will trigger an alarm to the platform.

Temperature and Humidity Monitoring Technology

Integrated with high-precision and wide-range temperature and humidity sensor. 24H real-time monitoring and recording the change of temperature and humidity.

Comprehensive Monitoring Technology

The device monitors the assets in an all aspects. In case of severe vibration, Abnormal temperature and humidity, abnormal light, alarms will be generated automatically.

Support buffer data

When the device enters an area with no network signal, the device stores the location information temporally, and uploads the historical location information to the platform when the device is back online.

Multiple Positioning Technology

Integrate GNSS positioning , LBS base station positioning, and other positioning technologies to fix the location of assets in real-time. Support electronic fences, transportation route planning and location deviation alarms*.

Data Visibility Technology

We provide web-based visualized management platform. This kind of insight enables you to be smarter in your planning and make more proactive, data-based decisions.

OTA Technology and Configuration Flexibility

Parameter configuration and firmware maintenance can be done locally and remotely(Servers and SMS).

Dual Server

The device supports dual IP simultaneous reporting.

**Data encryption ***

808 protocol data encryption supports RSA/AES/TEA*.

Network and Band Configuration

Support network and band configuration.

Set up your device

How to insert SIM card
  1. Remove the back cover.
  2. Then insert the Nano SIM card;
  3. Turn the switch to I. Then check the LED light is in normal state. see  LED indicators.

Figure_2 Remove the cover and insert SIM card

Remove the cover and insert SIM card 

Figure_3 Turn the switch to“I”

Figure_4 Check the LED indicators

Check the LED indicators

Platform configuration

Quickly set up your device by sending SMS commands to it:
Table 1 SMS commands

Commands Examples
IP=, , configure IP
APN=, , configure APN
TIMEZONE= configure time zone
TIMEGAP=+ configure report interval

More details about the commands in the list can be find in AOVX AT commands.

Default configuration settings

Report Interval

Report: Report every 3600s by default
Sample: Sampling every 3600s by default.

Device configuration

Work mode: Optional.
G sensor: Range: ±4G;Threshold:100; Time:3; Interval time:10bydefault.
Temp & Humi sensor:Interval:10s; Tmax:40; Tmin:10;Hmax:50; Hmin:10 by default.
Light:Threshold:500; Interval:10s by default.
Timezone:UTC+8 by default.
GNSS Galaxy: GPS+BD by default.

Protocol

Protocol:Type:JT808 by default; Ver:2013; Encry: NULL; Link: TCP by default. Report mask, Bluetooth mask and sensor mask are optional.

Installation
  • placed directly with the goods
  • Install via 3M tape

LED light indications

The red light shows the battery state of the device. The blue light shows the system state. More details find in the table2.

LED indication

Table 2 LED indication

COLOR DESCRIPTION STATE MEANING
Red Charge indicator On Charging
    Flash Battery is absent
    Off Full charging or disconnect with USB cable
Blue System indicator Flash slowly Work normally
    Flash quickly Work abnormally
    Off Switch off or in sleep mode

Safety Information

This message contains information on how to operate GX100 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device.

Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.

All wireless data transferring devices produce interference that may affect other devices which are placed nearby.

The programming must be performed using a PC with autonomic power supply

Installation and/or handling during a lightning storm is prohibited.

The device is susceptible to water and humidity.

AOVX is not responsible for any harm caused by wrong cables used for connection between PCandGX100

WARNING! Do not use GX100 device if it distracts driver or causes inconvenience due to GX100 placement. Device must not interfere with driver.

Battery should not be disposed of with general house hold waste. Bring damaged or worn out batteries to your local recycling center or dispose them to battery recycle bin found in stores.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules, These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).

This equipment complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions:

(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

The equipment complies with FCC Radiation exposure limits set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Customer Support

www.aovx.com

Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals