heyday B29+MQZ Compact Wireless Mouse Instruction Manual
- June 9, 2024
- Heyday
Table of Contents
heyday B29+MQZ Compact Wireless Mouse
Safety
- Do not use near any water source
- Do not modify or repair this device
- Do not use in high temperatures or extreme weather
- Do not use chemical detergents to clean your device, use a soft dry cloth
compact wireless mouse
-
top
-
bottom
connection channel for
wireless USB receiver
Bluetooth channel 1
Bluetooth channel 2
included
- Compact Wireless mouse (connect via wireless USB receiver or Bluetooth)
- USB receiver
- 1 x AA battery
Detailed setup
-
This mouse can be paired with up to 3 different devices
Use “Switch” button to switch connection channel between wireless USB receiver and 2 other Bluetooth channels.
-
Short press “Switch” button ONCE will show you current channel for example, if this mouse is currently set on “wireless USB receiver” LED indicator will start to flash for around 3 seconds.
-
Short press “Switch” button AGAIN To switch from different channels, press “Switch” again within that 3 seconds to switch to other channels.
Connect via wireless USB receiver
It is plug and play for USB receiver, make sure power is on, channel is set and then just plug in USB receiver into available USB A port on device.
Trouble shooting
If it is not working, try below steps to re-pair mouse and USB receiver
- Turn off your mouse and re-plug in USB receiver, turn on power (make sure channel is set on )
- Press “Connect” button (keep mouse close to receiver)
- If it does not work after 10 seconds, repeat step 1 to 3.
Connect / pair via Bluetooth in Windows
-
Turn on your mouse and set it on either Bluetooth channel or
-
Click on Start Menu (bottom left corner of your screen)
Go to Settings -> Device -> Bluetooth & other devices
Turn on Bluetooth -> Add Bluetooth or other device -> Add a device (Bluetooth) -
Press and HOLD “Connect” button to set mouse in pairing mode so that it can be found on your device (its LED will start to flash in green)
-
Click on “heyday compact mouse” to connect / pair (its LED will stop flashing and light up in green for around 3 seconds and then go off when pairing is completed)
Connect / pair via Bluetooth in Mac
- Turn on your mouse and set it on either Bluetooth channel or
- Click on Apple menu (top left corner of your screen) Go to System Preferences -> Bluetooth -> Turn Bluetooth on to set up Bluetooth device
- Press and HOLD “Connect” button to set mouse in pairing mode so that it can be found on your device (its LED will start to flash in green)
- Click on “heyday compact mouse” to connect / pair (its LED will stop flashing and light up in green for around 3 seconds and then go off when pairing is completed)
Trouble shooting
If it is not working, try below steps to re setup
- Turn off your mouse and turn on power again (make sure channel is set on or )
- Make sure to turn on Bluetooth on your device
- Press and HOLD “Connect” button to set mouse in pairing mode, make sure it is discoverable on your device and then connect with your mouse.
- If it does not work after 10 seconds, repeat step 1 to 3.
If it is not working on previous paired devices, make sure to turn on
Bluetooth on that device and set mouse on correct Bluetooth channel
For example, a tablet has paired with , and a laptop has paired with Set mouse
on if you want to use mouse on that tablet.
Low battery
If this LED starts to flash, it means you need to change battery
FCC ID: PRDMU124 Model: B2K-WG DPCI: 056-00-6362
Input: 1.5V⎓50mA Made in VIETNAM
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and 2) this device must
accept interference received, including interference that may cause undesired
operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
TargetCorp. Mpls. MN, 55403 Phone: 1-612-304-6073
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment. Battery life may vary depending on user and computing
conditions.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by TargetCorp. is under license.
Other trademarks and trade names are those of their respective owners.
Need some help?
Can’t get it to pair? Just have a question?
Call us at: 877-698-4883
Online at: TargetTechSupport.com