tp-link Tapo S210 Smart Light Switch User Guide
- June 4, 2024
- tp-link
Table of Contents
Quick Start Guide
Light Switch
User Guide
Install guide & FAQ:
Scan QR code or visit
https://www.tp-link.com/support/faq/3360/
Install with videos:
Scan QR code or visit
https://www.tp-link.com/support/download/tapo-s210/
7106509740 REV1.2.0
*Images may differ from your actual product.
Power Up Your Switch
- Slide the lock to the OPEN position. Then hold both sides of the faceplate and pull it away from the back.
- Insert the batteries. Make sure the positive and negative terminals of the batteries face the correct direction.
? FAQs on Batteries
Q1: Do I need to cut off power when replacing batteries after installation?****
– A1: No need to cut off power. The switch has current protection. Your safety is secured.
Q2: When do I need to replace batteries?****
– A2: If the LED blinks 3 times when you press the switch, the batteries need replacing.
Q3: What types of batteries can I use?****
– A3: 1.5 V AAA/LR03 alkaline batteries are recommended.
Note: Too high voltage might damage the switch. Check the max output voltage with the manufacturers if you use other types of batteries.
Set Up Your Switch
- Get the Tapo app from the App Store or Google Play.
https://www.tapo.com/app/download-app/ - Tap + the button in the app and select your model. Follow the instructions in the app to complete the setup.
Wire Your Switch
Install your switch following the wiring diagram below. Make sure you turn off the circuit breaker first.
- The hot / line wire is usually connected to the terminal “C” or “L” of your dumb switch. The switch also works if you do not distinguish between Lin and Lout wires.
- If the dumb switch is connected with a Neutral wire, cover it with the provided wire nut.
! Use Instructions
This switch can only be used with light fixtures and fans.
Connected fans should be below 50 W.
Do NOT connect the switch to heating devices such as bathroom heaters, water
heaters, and boilers.
*Images are only for demonstrations.
Internal LED & Button
For EU / UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:
863~865MHz / 863.35MHz / 25mW (e.r.p)
863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)
Before installing, servicing, or removing the switch, read and follow all
safety precautions including the following:
- Follow all national and local safety regulations and practices. If you are uncertain or uncomfortable when performing the installation, consult a qualified electrician.
- CAUTION – Risk of Electric Shock – More than one disconnect switch may be required to de-energize the equipment before servicing. A circuit breaker that disconnects the Line and Neutral conductor simultaneously is suitable. Ensure power is off at the circuit breaker before removing or installing any switch. Use a non-contact voltage tester to ensure the power is off.
- Do not install the Smart Switch with wet hands or when standing on wet or damp surfaces.
- Keep the device away from water, fire, humidity, or hot environments
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
- Do not use devices where wireless devices are not allowed.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU, and (EU)2015/863.
The original EU Declaration of Conformity may be found at
https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment Regulations
2017.
The original UK Declaration of Conformity may be found at
https://www.tapo.com/support/ukca/
For technical support, user guides, FAQs, warranty, and more, please visit
References
- Regulatory Compliance | Tapo
- UKCA | Tapo
- How to install Tapo 1 Gang 1 Way Smart Light Switch | TP-Link
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>