BlueMarine DC Power 2000 Energy Efficient Pump Instruction Manual
- June 9, 2024
- BlueMarine
Table of Contents
DC Power 2000 Energy Efficient Pump
Instruction Manual
Safety
- Read manual carefully before usage.
- Only suitable for indoor use.
- Ensure that water cannot reach the socket.
- Never let the pump run dry, keep it submerged at all times.
- Maximum water depth 1.5 meter
- The temperature of the fluid being pumped must never exceed 35°C.
- The pump must not be used to pump sewage, flammable, corrosive or explosive liquids (e.g. petroleum oil, petrol, thinner), grease, oils or foodstuffs.
- Unplug or switch off all appliances in the aquarium before carrying out maintenance.
- If damaged the supply cord cannot be replaced, the whole unit needs to be recycled.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instructions concerning the use of the appliance in a safe way and understand the hazards involved. Children may not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision.
Installation
-
Connect one cable from the controller to the pump cable and the other to the adapter cable.
To make sure there is a good connection slide the 2 plugs firmly into each other.
To make this easier you can soften the part that goes over the other plug with your fingers. -
Put the adapter’s AC plug into the power socket and the pump will start.
-
The controller is not waterproof. Damage caused by water is not covered by warranty.
Operation
Speed up/down
Adjust the flow rate by turning knob ‘a’ to the left (Min) or right (Max).
Maintenance
- Clean the pump monthly, depending on water and pollution conditions.
- Regular cleaning extents the lifetime of the pump
Cleaning
- clean the chamber inside with the brush;
- clean the surfaces of the magnet and the impeller;
- clean the shaft, bearing and other space parts inside.
Disassembling sequence
Remove the base by sliding it back and remove the front protector. Turn the
pump head clockwise (Face the water inlet of pump) and dismantle
it.
Take out the pump rotor.
Note: Please check whether the impeller works smoothly before
installation. If not, please adjust it accordingly.
Troubleshooting
- Stall protection: when something blocks the pump, so that the rotor cannot rotate, the pump will automatically stop running after 1 sec. Switch off the pump and remove the blockage. Now the pump can be turned on again.
- Water shortage protection: when there is too little water for the pump, it will stop running after 10 seconds. After 1 minute, the water pump will automatically start running. If there is still too little water, the pump will stop again after 10 seconds. After two of these cycles, the pump will continue in a cycle of stopping for 300 seconds and running for 10 seconds. This will ensure that the pump is not damaged. If enough water is detected during the 10-second operation of the pump, the protection is automatically released and the pump resumes normal operation. (only DC 2000)
Recycle information
**** This symbol indicates that this product (if it is discarded) may not be
disposed of with normal household waste.
Instead it must be handed in at an official collection centre (e.g. HWRC). Or
can be returned to the dealer when purchasing a similar new product. Follow
the applicable rules in your country for the separate collection of electrical
and electronic products. Separate collection and recycling are better for the
environment, public health and reduces waste.
Warranty
2 years manufacturer’s warranty on materials and construction defects. Devices must be returned complete with all components, accompanied with an official proof of purchase confirming a purchase date for any warranty claims. Incomplete devices of which parts are missing, and devices without proof of purchase are not eligible for warranty. After receiving and checking, we will determine whether the device will be repaired or replaced. For a device repaired or replaced under warranty, the remaining time of the original warranty period applies. Carefully read the instructions on installation, use and maintenance. Damage due to incorrect use, damage due to contamination or not cleaning the device, wear and damage to the rotor and damage to the cord are not covered by the warranty. Always keep the proof of purchase, without proof of purchase the warranty will be void!
Dealer stamp
Date of purchase
…………………. / …………………….. / 20 …………………
– Always keep proof of purchase, without purchase note no warranty!
Produced in China for:
www.aquadistri.com
Vlietweg 8 NL-4791 EZ Klundert
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>