BARCO UDM-4K22 Projector User Manual

UDM-4K22 Projector

UDM

ENABLING BRIGHT OUTCOMES

User manual

Product revision
Software Revision: 2.2
Barco Fredrikstad AS Habornveien 53, N-1630 Gamle Fredrikstad, Norway Support.fre@barco.com www.barco.com Barco NV Beneluxpark 21, 8500 Kortrijk, Belgium www.barco.com/en/support www.barco.com

Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.
Changes
Barco provides this manual ‘as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco web site https://www.barco.com/en/signin.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufacturers.
Product Security Incident Response
As a global technology leader, Barco is committed to deliver secure solutions and services to our customers, while protecting Barco’s intellectual property. When product security concerns are received, the product security incident response process will be triggered immediately. To address specific security concerns or to report security issues with Barco products, please inform us via contact details mentioned on https://www. barco. com/psirt. To protect our customers, Barco does not publically disclose or confirm security vulnerabilities until Barco has conducted an analysis of the product and issued fixes and/or mitigations.
Patent protection
Please refer to www.barco.com/about-barco/legal/patents.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer.

Disclaimer on GUI images used in this manual
The GUI images in this manual are example illustrations and should be treated as such. While the name of the projector displayed in the illustrations may be different from the projector model you are currently using, the menu lay-out and functionality is identical.
Disclaimer for camera usage
Barco provides a kit with a laser range finder and USB camera to help measure the distance from the front of the projector to the projected surface and to help monitor the performance of the projector. Barco disclaims any liability for any use of the USB camera outside this intended use.
Disclaimer for network usage
Barco highly recommends to install the projector in a closed network environment to minimize the risk of leaking, hacking or corrupting of company confidential information; commercial sensitive information and/or personal data. Furthermore, strengthen your network security to protect the projector against unauthorized access by third parties. To the maximum extent permitted by law, Barco disclaims any liability for the use of the projector in an open network environment.

Table of contents

1 Safety information……………………………………………………………………………………………………………………………………………………………… 9
1.1 General Considerations …………………………………………………………………………………………………………………………………………..10 1.2 Important safety instructions………………………………………………………………………………………………………………………………….. 11 1.3 Product safety labels…………………………………………………………………………………………………………………………………………………15 1.4 High Brightness precautions: Hazard Distance ……………………………………………………………………………………………….16 1.5 HD for fully enclosed projection systems……………………………………………………………………………………………………………18 1.6 HD in function of modifying optics ………………………………………………………………………………………………………………………..20 1.7 Radio equipment (optional) …………………………………………………………………………………………………………………………………….20 1.8 Compliance ………………………………………………………………………………………………………………………………………………………………….21 1.9 Download Product Manual ……………………………………………………………………………………………………………………………………..21
2 Getting Started…………………………………………………………………………………………………………………………………………………………………..23
2.1 Getting to know the projector …………………………………………………………………………………………………………………………………24 2.2 Power on the projector……………………………………………………………………………………………………………………………………………..26 2.3 Start image projection ………………………………………………………………………………………………………………………………………………27 2.4 Switching to ready mode …………………………………………………………………………………………………………………………………………30 2.5 Power off projector …………………………………………………………………………………………………………………………………………………….30
3 Pulse Remote Control Unit………………………………………………………………………………………………………………………………………..31
3.1 Pulse RCU, battery installation ……………………………………………………………………………………………………………………………..32 3.2 Pulse RCU, protocol setup ……………………………………………………………………………………………………………………………………..33 3.3 Pulse RCU, function of the on/off button…………………………………………………………………………………………………………….33 3.4 Using the RCU…………………………………………………………………………………………………………………………………………………………….34 3.5 Pulse RCU, Functionality overview………………………………………………………………………………………………………………………35 3.6 Pulse RCU, function of the “button pressed indicator”…………………………………………………………………………………..35 3.7 Pulse RCU, function of the “RGB filter” button …………………………………………………………………………………………………36 3.8 Displaying and Programming addresses into the RCU…………………………………………………………………………………36 3.9 Using the XLR connector of the RCU………………………………………………………………………………………………………………….36 3.10 Using the mini-jack connector of the RCU…………………………………………………………………………………………………………37 3.11 Pulse RCU, silicone protection sleeve (optional)…………………………………………………………………………………………….37
4 Input & Communication ……………………………………………………………………………………………………………………………………………….39
4.1 Introduction…………………………………………………………………………………………………………………………………………………………………..40 4.2 Local Keypad and LCD panel ………………………………………………………………………………………………………………………………..40 4.3 LCD touch panel…………………………………………………………………………………………………………………………………………………………41 4.4 Communication connections ………………………………………………………………………………………………………………………………….42 4.5 LED and Button indication chart ……………………………………………………………………………………………………………………………44

R5911443 /09 UDM

5

4.6 Pulse Quad Combo input Mk II ……………………………………………………………………………………………………………………………..45 4.7 Pulse Quad Combo input Mk I……………………………………………………………………………………………………………………………….46 4.8 Pulse Quad DP 1.2 input …………………………………………………………………………………………………………………………………………47 4.9 Pulse SFP input ………………………………………………………………………………………………………………………………………………………….48
5 GUI ­ Introduction……………………………………………………………………………………………………………………………………………………………49
5.1 Overview……………………………………………………………………………………………………………………………………………………………………….50 5.2 Navigation …………………………………………………………………………………………………………………………………………………………………….53 5.3 Test Patterns………………………………………………………………………………………………………………………………………………………………..55
6 GUI ­ Source ………………………………………………………………………………………………………………………………………………………………………57
6.1 Displaying a single source ………………………………………………………………………………………………………………………………………58 6.2 Displaying multiple sources: Stitched layouts…………………………………………………………………………………………………..58 6.3 Connector settings …………………………………………………………………………………………………………………………………………………….60
7 GUI ­ Image ………………………………………………………………………………………………………………………………………………………………………..63
7.1 Setting image levels manually ……………………………………………………………………………………………………………………………….64 7.2 Adjusting the sharpness…………………………………………………………………………………………………………………………………………..65 7.3 Adjusting the gamma correction……………………………………………………………………………………………………………………………66 7.4 Setting the desired Gamma type…………………………………………………………………………………………………………………………..67 7.5 Digital shift & zoom ……………………………………………………………………………………………………………………………………………………69 7.6 RealColor P7 ……………………………………………………………………………………………………………………………………………………………….73 7.7 Displaying HDR content …………………………………………………………………………………………………………………………………………..75 7.8 Dynamic contrast ……………………………………………………………………………………………………………………………………………………….76
8 GUI ­ Installation ……………………………………………………………………………………………………………………………………………………………..79
8.1 Configuring the lens, optical zoom-focus …………………………………………………………………………………………………………..80 8.2 Configuring the lens, shift………………………………………………………………………………………………………………………………………..80 8.3 Configuring the lens, dynamic focus ……………………………………………………………………………………………………………………81 8.4 Configuring the lens, Shift to center …………………………………………………………………………………………………………………….82 8.5 Configuring the lens, tilt sensor……………………………………………………………………………………………………………………………..83 8.6 Laser ranging ………………………………………………………………………………………………………………………………………………………………84 8.7 Manipulating the rigging frame ……………………………………………………………………………………………………………………………..85 8.8 Manipulating the rigging frame, center position……………………………………………………………………………………………….87 8.9 Orientation ……………………………………………………………………………………………………………………………………………………………………87 8.10 Scaling modes …………………………………………………………………………………………………………………………………………………………….88 8.11 Warping …………………………………………………………………………………………………………………………………………………………………………89
8.11.1 Warping ­ On/Off ……………………………………………………………………………………………………………………………………..90 8.11.2 Warping ­ Screen size ……………………………………………………………………………………………………………………………90 8.11.3 Warping ­ 4 corners adjustment………………………………………………………………………………………………………….93 8.11.4 Warping ­ Bow ………………………………………………………………………………………………………………………………………….95 8.11.5 Warping ­ Warp files ……………………………………………………………………………………………………………………………….99 8.11.6 Warping ­ Latency control in a multi projector setup ………………………………………………………………… 101 8.12 Blending & masking……………………………………………………………………………………………………………………………………………….. 102 8.12.1 Basic blend ……………………………………………………………………………………………………………………………………………… 103 8.12.2 Blend & Blend mask …………………………………………………………………………………………………………………………….. 105 8.12.3 Blend files………………………………………………………………………………………………………………………………………………… 107 8.12.4 Basic black level adjustment …………………………………………………………………………………………………………….. 108 8.12.5 RGB gain adjustment…………………………………………………………………………………………………………………………….110 8.12.6 Black level files………………………………………………………………………………………………………………………………………..111 8.13 Illumination …………………………………………………………………………………………………………………………………………………………………112 8.14 3D projection ……………………………………………………………………………………………………………………………………………………………..113 8.14.1 Active Stereo & Passive Stereo…………………………………………………………………………………………………………113 8.14.2 Setup process 3D projection ………………………………………………………………………………………………………………114

6

R5911443 /09 UDM

8.14.3 Connection possibilities………………………………………………………………………………………………………………………..114 8.14.4 3D Setup ……………………………………………………………………………………………………………………………………………………115
9 GUI ­ Profiles …………………………………………………………………………………………………………………………………………………………………..117
9.1 Profiles introduction …………………………………………………………………………………………………………………………………………………118 9.2 Profiles setup parameters ……………………………………………………………………………………………………………………………………..118 9.3 Saving settings to a new profile …………………………………………………………………………………………………………………………..119 9.4 Deleting a projector profile…………………………………………………………………………………………………………………………………… 121
10 GUI ­ System Settings…………………………………………………………………………………………………………………………………………….. 123
10.1 Remote control ………………………………………………………………………………………………………………………………………………………… 124 10.1.1 Broadcast address ……………………………………………………………………………………………………………………………….. 124 10.1.2 Projector address………………………………………………………………………………………………………………………………….. 124 10.1.3 IR sensors ……………………………………………………………………………………………………………………………………………….. 125
10.2 Host name – custom projector name setup…………………………………………………………………………………………………….. 126 10.3 Communication, LAN setup ………………………………………………………………………………………………………………………………… 127
10.3.1 Introduction to a Network connection …………………………………………………………………………………………….. 127 10.3.2 Wired IP address set up ……………………………………………………………………………………………………………………… 128 10.3.3 Wireless IP address set up………………………………………………………………………………………………………………… 130 10.3.4 LAN over HDBaseTTM IP address set up………………………………………………………………………………………. 133 10.4 DMX…………………………………………………………………………………………………………………………………………………………………………….. 135 10.5 Front XLR output voltage control ………………………………………………………………………………………………………………………. 137 10.6 GSM configuration………………………………………………………………………………………………………………………………………………….. 137 10.7 Changing the User Interface language……………………………………………………………………………………………………………. 138 10.8 Themes………………………………………………………………………………………………………………………………………………………………………. 139 10.9 Units (measurement) system setup………………………………………………………………………………………………………………….. 140 10.10 Controlling the backlight of the LCD Display …………………………………………………………………………………………………. 140 10.11 Date and time setup – manually …………………………………………………………………………………………………………………………. 141 10.12 Date and time setup – automatically …………………………………………………………………………………………………………………. 142 10.13 Power saving settings …………………………………………………………………………………………………………………………………………… 144 10.14 Lens features……………………………………………………………………………………………………………………………………………………………. 145 10.15 Factory reset…………………………………………………………………………………………………………………………………………………………….. 146 10.16 Lens Calibration………………………………………………………………………………………………………………………………………………………. 150 10.17 Flex brightness ………………………………………………………………………………………………………………………………………………………… 151 10.18 Rigging frame Calibration…………………………………………………………………………………………………………………………………….. 152 10.19 Electronic Convergence……………………………………………………………………………………………………………………………………….. 153 10.20 Operational mode …………………………………………………………………………………………………………………………………………………… 155 10.21 Capture mode ………………………………………………………………………………………………………………………………………………………….. 156 10.22 Login to advanced settings………………………………………………………………………………………………………………………………….. 156 10.23 List of open source licenses………………………………………………………………………………………………………………………………… 157
11 Advanced Settings ……………………………………………………………………………………………………………………………………………………… 159
11.1 Remote access ­ Enable source preview………………………………………………………………………………………………………. 160 11.2 Remote access ­ Enable camera preview …………………………………………………………………………………………………….. 161 11.3 Advanced Settings ­ Color………………………………………………………………………………………………………………………………….. 162 11.4 Advanced Settings ­ Statistics…………………………………………………………………………………………………………………………… 163 11.5 Checking the status of the Laser Banks………………………………………………………………………………………………………….. 164 11.6 Advanced settings ­ Tilt sensor calibration……………………………………………………………………………………………………. 165
12 GUI ­ Status menu……………………………………………………………………………………………………………………………………………………… 167
12.1 Status menu overview…………………………………………………………………………………………………………………………………………… 168
13 Product maintenance………………………………………………………………………………………………………………………………………………… 171
13.1 Software update………………………………………………………………………………………………………………………………………………………. 172

R5911443 /09 UDM

7

13.2 Cleaning the lens ……………………………………………………………………………………………………………………………………………………. 173 13.3 Cleaning the exterior of the projector……………………………………………………………………………………………………………….. 174 13.4 Cleaning / replace the air filters………………………………………………………………………………………………………………………….. 174
A Specifications …………………………………………………………………………………………………………………………………………………………………. 179
A.1 Specifications SDI inputs……………………………………………………………………………………………………………………………………… 180 A.2 Specifications HDMI inputs …………………………………………………………………………………………………………………………………. 180 A.3 Specifications HDBaseT inputs………………………………………………………………………………………………………………………….. 181 A.4 Specifications DisplayPort 1.2 inputs ………………………………………………………………………………………………………………. 182 A.5 Specifications SFP inputs ……………………………………………………………………………………………………………………………………. 183
B Video timing tables……………………………………………………………………………………………………………………………………………………… 185
B.1 Overview video timings…………………………………………………………………………………………………………………………………………. 186 B.2 Overview video timings SDI Inputs …………………………………………………………………………………………………………………… 187 B.3 Overview video timings HDMI 2.0 inputs………………………………………………………………………………………………………… 188 B.4 Overview video timings DisplayPort 1.2 inputs …………………………………………………………………………………………….. 190 B.5 Overview video timings HDBaseT inputs ……………………………………………………………………………………………………….. 192
C DMX chart…………………………………………………………………………………………………………………………………………………………………………. 195
C.1 DMX chart input board positioning ……………………………………………………………………………………………………………………. 196 C.2 DMX chart, Basic ……………………………………………………………………………………………………………………………………………………. 196 C.3 DMX chart, Extended…………………………………………………………………………………………………………………………………………….. 197
D WiFi & GSM compliance information …………………………………………………………………………………………………………….. 201
D.1 Compliance FCC…………………………………………………………………………………………………………………………………………………….. 202 D.2 Compliance IC …………………………………………………………………………………………………………………………………………………………. 202 D.3 KCC Certification…………………………………………………………………………………………………………………………………………………….. 203
E Regulatory information…………………………………………………………………………………………………………………………………………….. 205
E.1 Product compliance……………………………………………………………………………………………………………………………………………….. 206 E.2 China RoHS compliance………………………………………………………………………………………………………………………………………. 207 E.3 Taiwan RoHS compliance ……………………………………………………………………………………………………………………………………. 208 E.4 Turkey RoHS compliance…………………………………………………………………………………………………………………………………….. 209 E.5 Disposal information………………………………………………………………………………………………………………………………………………. 209 E.6 Contact information………………………………………………………………………………………………………………………………………………… 210 E.7 Production address………………………………………………………………………………………………………………………………………………… 210
Glossary ………………………………………………………………………………………………………………………………………………………………………………211
List of tools ……………………………………………………………………………………………………………………………………………………………………….. 213
Index …………………………………………………………………………………………………………………………………………………………………………………….. 215

8

R5911443 /09 UDM

Safety information

1

1.1 General Considerations ………………………………………………………………………………………………….10 1.2 Important safety instructions……………………………………………………………………………………………. 11 1.3 Product safety labels………………………………………………………………………………………………………15 1.4 High Brightness precautions: Hazard Distance……………………………………………………………………..16 1.5 HD for fully enclosed projection systems……………………………………………………………………………..18 1.6 HD in function of modifying optics ……………………………………………………………………………………..20 1.7 Radio equipment (optional) ……………………………………………………………………………………………..20 1.8 Compliance………………………………………………………………………………………………………………….21 1.9 Download Product Manual ………………………………………………………………………………………………21
About this document
Read this document attentively. It contains important information to prevent personal injury while installing and using the UDM projector. Furthermore, it includes several cautions to prevent damage to the UDM projector. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing the UDM projector.
Clarification of the term “UDM” used in this document
When referring in this document to the term UDM means that the content is applicable for following Barco poducts: · UDM 4K15, UDM 4K22, UDM W15, UDM W19, UDM W22, UDM 4k30, UDM W30
Model certification name
· UDM
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. Observing the specification mentioned in this chapter is critical for projector performance. Neglecting this can result in loss of warranty.

R5911443 /09 UDM

9

Safety information
1.1 General Considerations
WARNING: Be aware of suspended loads.
WARNING: Wear a hard hat to reduce the risk of personal injury.
WARNING: Be careful while working with heavy loads.
WARNING: Mind your fingers while working with heavy loads.
WARNING: In case of optical radiation emergency, please disconnect the device from the mains current; this by employing the mains switch. In case the mains switch is not easily accessible, the projectors shall be disconnected by other means for example the mains junction box. It is advised to employ the shutter or select a black image on the projector in order to reduce the risk of the emergency.
General safety instructions
· This product contains no user serviceable parts. Attempts to modify/replace mechanics or electronics inside the housing or compartments will violate any warranties and may be hazardous.
· Do not stare into beam when the projector is on. The bright light may result in permanent eye damage. · Before operating this equipment please read this manual thoroughly and retain it for future reference. · Installation and preliminary adjustments must be performed by qualified Barco personnel or by authorized
Barco service dealers. · All warnings on the projector and in the documentation manuals must be adhered to. · All instructions for operating and use of this equipment must be followed precisely. · All local installation codes should be adhered to.
Notice on safety
This equipment is built in accordance with the requirements of the applicable international safety standards. These safety standards impose important requirements on the use of safety critical components, materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of fire. Simulated single fault condition testing ensures the safety of the equipment to the user even when the equipment’s normal operation fails.
Notice on optical radiation
This projector embeds extremely high brightness (radiance) lasers; this laser light is processed through the projector’s optical path. Native laser light is not accessible by the end user in any use case. The light exiting the projection lens has been diffused within the optical path, representing a larger source and lower radiance value than native laser light. Nevertheless the projected light represents a significant risk for the human eye and skin when exposed directly within the beam. This risk is not specifically related to the characteristics of laser light but solely to the high thermal induced energy of the light source; which is equivalent with lamp based systems. Thermal retinal eye injury is possible when exposed within the Hazard Distance (HD). The HD is defined from the projection lens surface towards the position of the projected beam where the irradiance equals the maximum permissible exposure as described in the chapter “Hazard Distance”.
WARNING: No direct exposure to the beam within the hazard distance shall be permitted, RG3 (Risk Group 3) IEC EN 62471-5:2015

10

R5911443 /09 UDM

Safety information
CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Notice on laser radiation
The laser distance meter that is optional equipment for this projector can emit a class 2 laser ranging beam of 0.95 mW / 638 nm. When installed correctly, this distance meter is located on the front side of the projector (see ). The laser beam can be enabled by either pressing the button on the equipment, via the projector menu, or via the projector software. Thermal retinal eye injury is possible when staring into the laser ranging beam.

Image 1­1
WARNING: Laser Radiation — Do not stare into laser ranging beam, Class 2 IEC EN 60825-1:2014 See the product safety manual for details.
Users definition
Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having appropriate technical training and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize the potential risk to themselves or other persons. The term USER and OPERATOR refers to any person other than SERVICE PERSONNEL, AUTHORIZED to operate professional projection systems.
The UDM projector is intended “FOR PROFESSIONAL USE ONLY” by AUTHORIZED PERSONNEL familiar with potential hazards associated with high voltage, high intensity light beams and high temperatures generated by the light source and associated circuits. Only qualified SERVICE PERSONNEL, knowledgeable of such risks, are allowed to perform service functions inside the product enclosure.
1.2 Important safety instructions
To prevent risk of electrical shock
· This product should be operated from a mono phase AC power source. Ensure that the mains voltage and capacity matches the projector electrical ratings:120-180V/200-240V (+/-10%), 16/12A 60/50Hz. If you are unable to install the AC requirements, contact your electrician. Do not defeat the purpose of the grounding.
· This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. · If none of the supplied power cables are the correct one, consult your dealer. · If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.
Do not defeat the purpose of the grounding-type plug. · Never use 2- wire power cords, as this is dangerous and could lead to electrical shock. Always use a
power connector with a ground terminal. · Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the
cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself. · Use only the power cord supplied with your device. While appearing to be similar, other power cords have
not been safety tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer. · If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug. · Do not operate the projector with a damaged cord. Replace the cord. · Do not operate the projector if the projector has been dropped or damaged – until it has been examined and approved for operation by qualified service personnel. · Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.

R5911443 /09 UDM

11

Safety information
· If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated for less amperage than the projector may overheat.
· Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock.
· Make sure that no objects enter into the vents and openings of the set. · Do not expose this projector to rain or moisture. · The projector is designed for indoor use only. Never operate the unit outdoors. · Do not immerse or expose this projector in water or other liquids. · Do not spill liquid of any kind on this projector. · Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified
service personnel before resuming operations. · Do not disassemble this projector, always take it to qualified service personnel when service or repair work
is required. · Do not use an accessory attachment which is not recommended by the manufacturer. · Lightning – For added protection for this video product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.
To prevent personal injury
· To prevent injury and physical damage, always read this manual and all labels on the system before powering the projector or adjusting the projector.
· To prevent injury, take note of the weight of the projector. The weight of a basic projector is about 48 kg (105 lb) without lens.
· To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures. · Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to
the eye. · Warning: extremely high brightness projector: This projector embeds extremely high brightness
(radiance) lasers; this laser light is processed through the projectors optical path. Native laser light is not accessible by the end user in any use case. The light exiting the projection lens has been diffused within the optical path, representing a larger source and lower radiance value than native laser light. Nevertheless the projected light represents a significant risk for the human eye when exposed directly within the beam. This risk is not specific related to the characteristics of laser light but solely to the high thermal induced energy of the light source; which is comparable with lamp based systems. Thermal retinal eye injury is possible when exposed within the Hazard Distance. The Hazard Distance (HD) is defined from the projection lens surface towards the position of the projected beam where the irradiance equals the maximum permissible exposure as described in the chapter “High Brightness precautions: Hazard Distance”, page 16. · High Brightness Warning: The projector light source may not be switched on or the shutter must be closed when no projection lens is installed. · Based on international requirements, no person is allowed to enter the projected beam within the zone between the projection lens and the related Hazard Distance (HD). This shall be physically impossible by creating sufficient separation height or by placing optional barriers. Within the restricted area operator training is considered sufficient. The applicable separation heights are discussed in “High Brightness precautions: Hazard Distance”, page 16. · Warning: Laser radiation when optional laser distance meter is installed. Do not stare into laser ranging beam. Class 2 laser beam could result in damage to the eye. · Don’t put your hand in front of the beam. · This product contains no user serviceable parts. Attempts to modify/replace mechanics or electronics inside the housing or compartments will violate any warranties and may be hazardous. This kind of operations shall only be performed by Barco authorized service personnel. · Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect from the wall outlet. · When required to switch off the projector, to access parts inside, always disconnect the power cord from the power net. · The power input at the projector side is considered as the disconnect device. When required to switch off the projector, to access parts inside, always disconnect the power cord at the projector side. In case the power input at the projector side is not accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be installed nearby the projector and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.

12

R5911443 /09 UDM

Safety information
· Do not stack or hang projectors without using the stacking frame. · Max units in stacked configuration, 3 units. · Max units in hanging configuration, 2 units. · When hanging projectors on a truss with the Barco stacking frame, always secure the stack with safety
cables between the projectors and the truss. · When using the projector in a hanging configuration, always mount 2 safety cables. See installation
manual for the correct use of these cables. · Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious
damage to it and possible injury to the user. · Only place the projector on a stable surface, or mount it securely using an approved ceiling mount rig. · It is hazardous to operate without lens or shield. Always switch the output light off when replacing a lens. · Lenses or shields shall be changed if they have become visibly damaged to such an extent that their
effectiveness is impaired. For example by cracks or deep scratches. · Cooling liquid circuit. The projector contains a cooling circuit filled with Mono- ethylene glycol (1,2-ethane
diol) and inhibitors in aqueous solution (34% active). If the unlikely event that the cooling circuits have a leak, switch off the device and contact qualified service personnel. The liquid is not for household use. Keep out of reach of children. Harmful by oral intake. Avoid exposure to pregnant women. Avoid contact with eyes, skin and clothing. Avoid inhale of the noxious fumes. · Never point or allow light to be directed on people or reflective objects within the HD zone. · All operators shall have received adequate training and be aware of the potential hazards. · In case of using an external cooling system position the hoses of the cooling system so that they will not be tripped over, pulled, or contact hot surfaces.
To prevent fire hazard
· Do not place flammable or combustible materials near the projector! · Barco large screen projection products are designed and manufactured to meet the most stringent safety
regulations. This projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe. Exposing flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the projector whereby no flammable or combustible materials are present. The exclusion zone must be not less than 40 cm (16″) for this projector. · Do not place any object in the projection light path at close distance to the projection lens output. The concentrated light at the projection lens output may result in damage, fire or burn injuries. · Ensure that the projector is solidly mounted so that the projection light path cannot be changed by accident. · Do not cover the projector or the lens with any material while the projector is in operation. . Mount the projector in a well ventilated area away from sources of ignition and out of direct sun light. Never expose the projector to rain or moisture. In the event of fire, use sand, CO2 or dry powder fire extinguishers. Never use water on an electrical fire. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this projector. · Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided. · Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent hot exhaust air from projector and cooling system to the outside of the building. · Let the projector cool completely before storing. Remove cord from the projector when storing.
To prevent battery explosion
· Danger of explosion if battery is incorrectly installed. · Replace only with the same or equivalent type recommended by the manufacturer. · For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal
rules and regulations to ensure proper disposal.

R5911443 /09 UDM

13

Safety information
To prevent projector damage
· The air filters of the projector must be cleaned or replaced on a regular basis. Cleaning the booth area would be monthly-minimum. Neglecting this could result in disrupting the air flow inside the projector, causing overheating. Overheating may lead to the projector shutting down during operation.
· The projector must always be installed in a manner which ensures free flow of air into its air inlets. · If more than one projector is installed in a common projection booth, the exhaust air flow requirements are
valid for EACH individual projector system. Note that inadequate air extraction or cooling will result in decreased life expectancy of the projector as a whole as well as causing premature failure of the lasers. · In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC) and safety requirements, it should always be operated with all of it’s covers in place. · Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The device should not be placed in a built-in installation or enclosure unless proper ventilation is provided. · Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and remove all power from the projector. Do not operate the projector again until it has been checked by qualified service personnel. · Do not block the projector cooling fans or free air movement around the projector. · Do not use this equipment near water. · Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as high power laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror DevicesTM in which case there is a loss of warranty. · Never place the projector in direct sunlight. Sunlight on the lens can severely damage the Digital Mirror DevicesTM in which case there is a loss of warranty. · Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory. · Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution. · To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti- reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. For lens cleaning follow the instructions precisely as stipulated in the projector manual. · Only use zoom lenses of the Barco TLD+ series on the 4K models of the projector. Using other lenses will damage the internal optics. For suitable fixed TLD+ lenses contact Barco or see Barco website. · Allowed ambient temperature range depends on altitude: – between 0 and 1000 meter altitude: ambient temperature range = 0°C (32°F) to 40°C (104°F) – between 1000 and 3000 meter altitude: ambient temperature range = 0°C (32°F) to 30°C (86°F) · Rated humidity = 0% RH to 80% RH Non-condensed.
On servicing
· Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials and risk of electric shock.
· Opening or removing of the covers may expose you to laser radiation and optical hazard. · Refer all servicing to qualified service personnel. · Attempts to alter the factory-set internal controls or to change other control settings not specially discussed
in this manual can lead to permanent damage to the projector and cancellation of the warranty. · Replacement parts: When replacement parts are required, be sure the service technician has used original
Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty. · Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

14

R5911443 /09 UDM

Safety information

Malfunction unit
Remove all power from the projector and refer servicing to qualified service technicians under the following conditions:
· When the power cord or plug is damaged or frayed. · If liquid has been spilled into the equipment. · If the product has been exposed to rain or water. · If the product does not operate normally when the operating instructions are followed. Adjust only those
controls that are covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. · If the product has been dropped or the cabinet has been damaged. · If the product exhibits a distinct change in performance, indicating a need for service.
Stacking and transporting
· Stack maximum 2 rental flight cases high. Never higher. · Surface on which flight case is standing must be level to ensure that the total load is evenly spread out
among the four wheels. The surface must also be able to support the load safely. · Before stacking or transporting flight cases, check the wheels and their fixation screws for wear or defects. · Before stacking or transporting flight cases, check that the four lock handles on each flight case are in
good working order and locked securely. · When stacked, make sure the wheels of the upper flight case are precisely positioned in the stacking
dishes of the flight case below. · Stacked flight cases may not be moved. Before stacking, the lower flight case must already be in its final
resting position before placing the second upon it. · Never stack loaded flight cases in a truck or other transport medium, unless each flight case is rigidly
strapped tight. · In the event of a wheel breaking, flight cases must be rigidly strapped tight to prevent a stack collapsing. · Use an appropriate forklift to raise flight cases and take the necessary precautions to avoid personnel
injury.
Safety Data Sheets for Hazardous Chemicals
For safe handling information on chemical products, consult the Safety Data Sheet (SDS). SDSs are available upon request via safetydatasheets@barco.com.

1.3 Product safety labels

Light beam related safety labels

Label image

Label description Hazard RG3: not for household use symbol

Label location

Hazard RG3: optical radiation warning symbol

R5911443 /09 UDM

15

Safety information

Label image

Label description
Hazard class 2: laser radiation warning symbol. 0.95 mW – 638 nm.

Label location

WARNING! DO NOT LOOK INTO THE BEAM NO DIRECT EYE EXPOSURE TO THE PROJECTOR BEAM IS PERMITTED LASER RADIATION – DO NOT STARE INTO LASER RANGING BEAM RG3 IEC EN 62471-5:2015 CLASS 2 IEC EN 60825-1:2014 HAZARD DISTANCE: CONSULT SAFETY MANUAL
THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR LASER PRODUCTS UNDER 21 CFR 1040, EXCEPT WITH RESPECT TO THOSE CHARACTERISTICS AUTHORIZED BY VARIANCE NUMBER 2016-V-0144 EFFECTIVE ON DECEMBER 12, 2019.
– RG3 IEC EN 62471-52015 CLASS 2 IEC EN 60825-1 2014
– RG3 IEC EN 62471-52015 CLASS 2 IEC EN 60825-1 2014
ATTENTION! NE PAS REGARDER LE FAISCEAU DU PROJECTEUR EVITER TOUTE EXPOSITION DIRECTE DES YEUX AU FAISCEAU DU PROJECTEUR RAYONNEMENT LASER – NE PAS REGARDER DANS LE FAISCEAU DU TELEMETRE RG3 IEC EN 62471-5:2015 CLASS 2 IEC EN 60825-1:2014 DISTANCE DE SECURITE: CONSULTER LE MANUEL DE SECURITE
1.4 High Brightness precautions: Hazard Distance
HD Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or the energy per surface unit becomes lower than the applicable exposure limit on the cornea or on the skin. The light beam is considered (to be) unsafe for exposure if the distance from a person to the light source is less than the HD.
Restriction Zone (RZ) based on the HD
The HD depends on the amount of lumens produced by the projector and the type of lens installed. See chapter “HD in function of modifying optics”, page 20.
To protect untrained end users (as cinema visitors, spectators) the installation shall comply with the following installation requirements: Operators shall control access to the beam within the hazard distance or install the product at a height that will prevent spectators’ eyes from being in the hazard distance. Radiation levels in excess of the limits will not be permitted at any point less than 2.0 meter (SH) above any surface upon which persons other than operators, performers, or employees are permitted to stand or less than 1.0 meter (SW) lateral separation from any place where such persons are permitted to be. In environments where unrestrained behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 meter to prevent potential exposure, for example by an individual sitting on another individual’s shoulders, within the HD.
These values are minimum values and are based on the guidance provided in IEC 62471-5:2015 section 6.6.3.5.
The installer and user must understand the risk and apply protective measures based upon the hazard distance as indicated on the label and in the user information. Installation method, separation height, barriers,

16

R5911443 /09 UDM

Safety information

detection system or other applicable control measure shall prevent hazardous eye access to the radiation within the hazard distance.
For example, projectors that have a HD greater than 1 m and emit light into an uncontrolled area where persons may be present should be positioned in accordance with “the fixed projector installation” parameters, resulting in a HD that does not extend into the audience area unless the beam is at least 2.0 meter above the floor level. In environments where unrestrained behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 meter to prevent potential exposure, for example by an individual sitting on another individual’s shoulders, within the HD. Sufficiently large separation height may be achieved by mounting the image projector on the ceiling or through the use of physical barriers.

RA

SIDE VIEW (A)

TH

TOP VIEW (B)

TH

H<SH

HD

RZ SH

SW

RA

RZ

HD

H>SH

LRZ SW
LRZ

Image 1­2 A Side view B Top view RA Restricted Access location (boot area of projector). TH Theater RZ Restriction Zone in the theater

HD Hazard Distance LRZ Length Restriction Zone in the theater H Height between surface floor and the light beam SH Separation Height SW Separation Width

Based on national requirements, no person is allowed to enter the projected beam within the zone between the projection lens and the related hazard distance (HD). This shall be physically impossible by creating sufficient separation height or by placing barriers. The minimum separation height takes into account the surface upon which persons other than operator, performers or employees are permitted to stand.
On Image 1­ 3 a typical setup is displayed. It must be verified if these minimum requirements are met. If required a restricted zone (RZ) in the theater must be established. This can be done by using physical barrier, like a red rope as illustrated in Image 1­3.
The restricted area sticker can be replaced by a sticker with only the symbol.

Image 1­3

R5911443 /09 UDM

17

Safety information
USA market
For LIPs (Laser Illuminated Projectors) installed in the USA market other restriction zone conditions apply.
LIPs for installation in restrained environment (cinema theaters, business rooms, class rooms, museums …) shall be installed at height vertically above the floor such that the bottom plane of the hazard distance zone shall be no lower than 2.5 meters above the floor. Horizontal clearance to the hazard distance zone shall be not less than 1 meter. Alternatively, in case the height of the separation barrier for the horizontal clearance is at least 1 meter high then the horizontal clearance (SW) can be reduced to:
· 0 meter if the height of the hazard zone is minimum 2.5 meter. · 0.1 meter if the height of the hazard zone is minimum 2.4 meter. · 0.6 meter if the height of the hazard zone is minimum 2.2 meter.
LIPs for installations in unrestrained environment (concerts, …) shall be installed at a height vertically above the floor such that the bottom plane of the Hazard distance Zone shall be no lower than 3 meters above the floor. Horizontal clearance to the hazard distance zone shall be not less than 2.5 meters. Any human access horizontally to the Hazard Zone, if applicable, shall be restricted by barriers. If human access is possible in an unsupervised environment, the horizontal or vertical clearances shall be increased to prevent exposure to the hazard distance zone.
The LIP shall be installed by Barco or by a trained and Barco-authorized installer or shall only be transferred to laser light show variance holders. This is applicable for dealers and distributors since they may need to install the LIP (demo install) and/or they transfer (sell, rent, lease) the LIP. Dealers and distributors shall preserve sales and installation records for a period of 5 years. Variance holders may currently hold a variance for production of Class IIIB and IV laser light shows and/or for incorporating RG3 LIPs. Laser light show variance for RG3 LIPs can be requested by mailing the application to RadHealthCustomerService@fda.hhs.gov.
The installation checklist for laser illuminated RG3 projectors must be fully completed after the installation. The installation checklist can be downloaded from the Barco website. The installer shall preserve the checklist for a period of 5 years.
Install one or more readily accessible controls to immediately terminate LIP projection light. The power input at the projector side is considered as a reliable disconnect device. When required to switch off the projector, disconnect the power cord at the projector side. In case the power input at the projector side is not accessible (e. g. truss mount), the socket outlet supplying the projector shall be installed nearby the projector and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.
1.5 HD for fully enclosed projection systems
HD Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or the energy per surface unit becomes lower than the applicable exposure limit on the cornea or on the skin. The light beam is considered (to be) unsafe for exposure if the distance from a person to the light source is less than the HD.
Restriction Zone (RZ) based on the HD
The projector is also suitable for rear projection applications; projecting a beam onto a defuse coated projection screen. As displayed in Image 1­ 4 two areas should be considered: the restricted enclosed projection area (RA) and the observation area (TH).

18

R5911443 /09 UDM

RESTRICTED AREA

RESTRICTED AREA

RA PR

Safety information

sw

TH

RZ
sw PD

HDDIFFUSE

sw
HD
REFLECTION

sw

Image 1­4 RA Restricted Access location (enclosed projection area). PR Projector. TH Theater (observation area).

RZ Restriction Zone. PD Projection Distance. SW Separation Width. Must be minimum 1 meter.

For this type of setup 3 different HD shall be considered:
· HD as discussed in “High Brightness precautions: Hazard Distance”, page 16, relevant for intrabeam exposure.
· HDreflection : the distance that has to be kept restrictive related to the reflected light from the rear projection screen.
· HDdiffuse : the relevant distance to be considered while observing the diffuse surface of the rear projection screen.
As described in “High Brightness precautions: Hazard Distance”, page 16, it is mandatory to create a restricted zone within the beam areas closer than any HD. In the enclosed projection area the combination of two restricted zones are relevant: The restricted zone of the projected beam toward the screen; taking into account 1 meter Separation Width (SW) from the beam onward. Combined with the restricted zone related to the rear reflection from the screen (HDreflection); also taking into account a 1 meter lateral separation.
The HDreflection distance equals 25% of the difference between the determined HD distance and the projection distance to the rear projection screen. To determine the HD distance for the used lens and projector model see chapter “HD in function of modifying optics”, page 20.
HDreflection = 25% (HD ­ PD)
The light emitted from the screen within the observation shall never exceed the RG2 exposure limit, determined at 10 cm. The HDdiffuse can be neglected if the measured light at the screen surface is below 5000 cd/m² or 15000 LUX.

R5911443 /09 UDM

19

Safety information
1.6 HD in function of modifying optics
Hazard distance

Image 1­5

1.7 Radio equipment (optional)

CE Conformity

AT BE BG CH CY CZ DK DE EE IE EL ES FI FR HR HU IS IT LI LV LT LU NL NO PL PT RO SE SI SK TR UKNI

This device may be equipped with WiFi & GSM modules for Pulse Input & Communication unit, which are fit for use in the European Union countries, EFTA and Turkey.
This device is restricted to indoor use only when operating in the 5150 to 5250 MHz frequency range.

Hereby, Barco declares that the radio equipment type UDM is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www. barco. com/support

20

R5911443 /09 UDM

Safety information

WiFi & GSM module
For WLAN: · Frequency: 2402 MHz – 2482 Mhz · Max EIRP: 19 dBm · Frequency: 5150 ­ 5350 MHz / 5470 ­ 5725 Mhz · Max EIRP: 23 dBm
For UMTS: · Band 1:
– Frequency: 2100 MHz – Max EIRP: 24 dBm · Band 8: – Frequency: 900 MHz – Max EIRP: 24 dBm

For GSM: · E-GSM:
– Frequency: 900 MHz – Max EIRP: 33.5 dBm · EDGE: – Frequency: 900 MHz – Max EIRP: 28 dBm · DCS: – Frequency: 1800 MHz – Max EIRP: 30.5 dBm · EDGE: – Frequency: 1800 MHz – Max EIRP: 27 dBm

1.8 Compliance

UK Compliance
UK

This product is fit for use in the UK.

Authorised Representative: Barco UK Ltd

Address:

Building 329, Doncastle Road

Bracknell RG12 8PE, Berkshire, United Kingdom

1.9 Download Product Manual
Download Product Manual
Product manuals and documentation are available online at www.barco.com/td. Registration may be required; follow the instructions given on the website. IMPORTANT! Read Installation Instructions before connecting equipment to the mains power supply.

R5911443 /09 UDM

21

Safety information

22

R5911443 /09 UDM

Getting Started

2

2.1 Getting to know the projector ……………………………………………………………………………………………24 2.2 Power on the projector ……………………………………………………………………………………………………26 2.3 Start image projection …………………………………………………………………………………………………….27 2.4 Switching to ready mode …………………………………………………………………………………………………30 2.5 Power off projector…………………………………………………………………………………………………………30
About this chapter
This chapter and by extension this whole document, the user manual, is intended for the user who want’s to operate the projector. It does not contain installation instructions because the installation has to be done by trained and qualified service technicians. Refer to the projector installation manual for detailed installation instructions.

R5911443 /09 UDM

23

Getting Started
2.1 Getting to know the projector
Orientation convention
This manual refers to the left side of the projector as the side at your left hand when standing behind the projector and looking at the projection screen in front of the projector.

T

B

L

R
Image 2­1 T Top L Left F Front
Projector component location
1

F
R Right B Back

2

34

Image 2­2

1 Dust filter top air inlet 2 Dust filter side air inlet 3 Input & Communication module 4 IR receiver projector right side

5

67 8

5 Dust filter front air inlet 6 Auxiliary connector (for external shutter, DMX, …) 7 IR receiver projector front side 8 Distance meter (optional)

24

R5911443 /09 UDM

Getting Started

OVERVOLTAGE

Image 2­3

9 10 11 12 13

9 IR receiver projector rear side 10 Mains power input socket (for C19 plug) 11 Power ON/OFF switch

12 Overvoltage status light 13 USB port (to control motorized rigging frame)

For detailed info about the Input & Communication module see chapter “Input & Communication”, page 39.

Environment conditions
Table below summarizes the physical environment in which the projector safely operates or can be stored.

Environment Ambient Temperature (depends on altitude)
Humidity
Altitude

Operating 0-1000 meter: 0°C (32°F) to 40°C (104°F) 1000-3000 meter: 0°C (32°F) to 30°C (86°F) 0% RH to 80% RH Non-condensed
-60 m (-197 Ft) to 3000 m (9843 Ft)1

Non-Operating -15°C (5°F) to 60°C (140°F)
0% RH to 90% RH NonCondensed -60 m (-197 Ft) to 10000 m (32810 Ft)

Projector airflow
The projector has three air inlets: one at the top, one at the front and one at the right side of the projector. Each air inlet is equipped with a dust filter. For cleaning/replacement instructions see chapter “Product maintenance”, page 171.
There is only one air outlet which is located at the rear of the projector.

1. For PRC (People’s Republic of China) the certified altitude is specified on the product label.

R5911443 /09 UDM

25

Getting Started

Image 2­4
CAUTION: Keep the air inlets and outlet at all times free. Make sure there is a minimum distance of 40 cm (15.7 in) between the air outlet and the nearest solid object.
Projector Infra Red receivers and Remote Controle Unit
The projector has three Infra Red receivers: one at the rear (next to the power input), one at the front (below the lens holder) and one at the right side (integrated in the Input & Communication module). Point the Remote Controle Unit (RCU) directly to the Infra Red (IR) receiver. Make sure you are within the effective operating distance (30 m, 100 ft in a straight line) The RCU will not function properly if strong light strikes the IR sensor window or if there are obstacles between the RCU and the IR sensor.

45° 45°

45° 45°

45° 45°

Image 2­5
For detailed info about the RCU see chapter “Pulse Remote Control Unit”, page 31.
2.2 Power on the projector
How to power on
1. Does the OVERVOLTAGE status light (reference 1) lit up? · If yes, pull out the power cord immediately. Contact a qualified technician to check the power net.

26

R5911443 /09 UDM

Getting Started
Warning: Never switch on the projector if the OVERVOLTAGE status light lit up. Neglecting will cause irreversible damage to the projector. · If no, proceed with the next step. 2. Press the mains switch (reference 2) to switch on this projector.
OVERVOLTAGE

Image 2­6

2 1

· When ‘0’ is pressed, the projector is switched off. · When ‘I’ is pressed, the projector is switched on.

The projector starts up to ready mode. The Power on/off button will blink until ready mode is achieved. Once in ready mode, the Power on/off button will be lit WHITE.

The start up screen is displayed on the touch panel.

Image 2­7
3. Press the Power on/off button on the projector, or the Power On button on the remote control. The projector will continue to power on mode. The Power on/off button will blink until the projector is ready. Once the projector is ready, the Power button will be lit BLUE.

Image 2­8
The background image of the startup screen and info screens can be changed with Projector Toolset with an installed UDM plug-in.
2.3 Start image projection
Connect the source
1. Connect the source cable with the appropriate input port on the Input & Communication module. Tip: See chapter “Input & Communication”, page 39, for more info about supported input formats.

R5911443 /09 UDM

27

Getting Started

Image 2­9 Example of connecting an HDMI source.
2. Check if the SYNC LED lit up ORANGE (reference 1). This indicates that the sync is detected on the input signal.
1 Image 2­10
Select the source
1. Press the Input button (reference I ) on the remote control or local keypad.
I I
Image 2­11
The Source selection menu opens on the LCD display.

28

R5911443 /09 UDM

Getting Started

Image 2­12 Example of the input selection menu
2. Use the arrow keys to select the desired source. · the SEL LED (reference 2) of the selected source lit up GREEN, and · the image of the selected source is projected.
2
Image 2­13
Quick test pattern selection
1. Press the Test pattern button (references P) on the remote control or local keypad.
P

P
Image 2­14
The Test pattern menu opens on the LCD display. 2. Use the arrow keys to select the desired test pattern.

R5911443 /09 UDM

29

Getting Started
2.4 Switching to ready mode
How to switch to ready mode
1. Press and hold the Power on/off button for 3 seconds on the local keypad, or press the Power Off button on the remote control. The projector goes to Ready mode. The after-cooling cycle will start (about 30 seconds). During this period the Power on/off button will blink. Once the after-cooling cycle has ended, the projector will be in ready mode and the Power on/off button will be lit WHITE.

3 s

30 s

Image 2­15
While in ready mode, you can still navigate through the menus and set a limited amount of parameters. Depending on the power savings settings of your device, if left untouched the projector will eventually go into standby or eco mode.
2.5 Power off projector
CAUTION: This procedure assumes the projector is in standby or ready mode.
How to power off
1. Switch off the projector with the mains switch. ‘0’ must be pressed.

1 Image 2­16 Mains switch
2. Unplug the power cord from the projector.

30

R5911443 /09 UDM

Pulse Remote Control Unit

3

3.1 Pulse RCU, battery installation …………………………………………………………………………………………32 3.2 Pulse RCU, protocol setup ………………………………………………………………………………………………33 3.3 Pulse RCU, function of the on/off button ……………………………………………………………………………..33 3.4 Using the RCU ……………………………………………………………………………………………………………..34 3.5 Pulse RCU, Functionality overview ……………………………………………………………………………………35 3.6 Pulse RCU, function of the “button pressed indicator” …………………………………………………………….35 3.7 Pulse RCU, function of the “RGB filter” button ………………………………………………………………………36 3.8 Displaying and Programming addresses into the RCU……………………………………………………………36 3.9 Using the XLR connector of the RCU …………………………………………………………………………………36 3.10 Using the mini-jack connector of the RCU……………………………………………………………………………37 3.11 Pulse RCU, silicone protection sleeve (optional) …………………………………………………………………..37

R5911443 /09 UDM

31

Pulse Remote Control Unit

3.1 Pulse RCU, battery installation
About the batteries for the remote control
No batteries are included in the packaging. User has to buy batteries himself. Use 2 AA size (alkaline) batteries in the remote control. Before using your remote control, install the batteries first.
How to install
1. Push the battery cover tab with the fingernail a little backwards (1) and pull, at the same time, the cover upwards (2).

1

2

Image 3­1
2. Insert the two AA size batteries, making sure the polarities match the + and – marks inside the battery compartment. Tip: Use alkaline batteries for optimum range and life time.

+ –
+-

Image 3­2
3. Insert (1) both lower tabs of the battery cover in the gaps at the bottom of the remote control, and press (2) the cover until it clicks in place.
2

+ –

1

+-

Image 3­3
When replacing batteries, the broadcast address of the RCU will be reset to its default value ‘0’.

32

R5911443 /09 UDM

Pulse Remote Control Unit
CAUTION: Replace with the correct battery type. Use two AA size batteries. There is a risk of explosion if the battery is replaced with an incorrect type.
CAUTION: Replace the battery as explained above. There is a risk of explosion if the battery is incorrectly installed.
3.2 Pulse RCU, protocol setup
About the used protocol
The protocol is the code send out by the remote control when a button is pressed. Depending on this code, the projector can decode the signals. The remote control can be used with two different protocols: RC5 and NEC. Depending on the projector to control the remote control can be switched between these protocols.
Which protocol to use
· The NEC protocol has to be used for Barco projectors based on the Pulse platform: F70, F80, F90, HDX 4K, UDX, UDM, XDL, etc.
· The RC5 protocol has to be used all legacy Barco projectors: HDQ 2k40, HDF, HDX W, etc.
How to set
1. Remove the cover. For more info on how to remove, see “Pulse RCU, battery installation”, page 32. 2. Place the switch in the desired position.

Image 3­4
Remarks when using the RC5 protocol
Due to new or updated functionality not all buttons of the Pulse RCU are one- to-one compatible with the legacy Barco RCU and projectors. Take the following limitations into account:
· Buttons Shutter open and Shutter close emit the same code when in RC5 mode. This because the legacy RCU’s only had 1 button for Shutter functionality.
· Buttons Power on and Power off emit the same code when in RC5 mode. This because the legacy RCU’s only had 1 button for Power functionality.
· The RGB filter button is not supported. · The Input selection button is not supported. · The Default value button is not supported. · The Macro button is not supported.
3.3 Pulse RCU, function of the on/off button
Function of the remote control on/off button
The Pulse remote control unit has at the front side an on/off switch (reference 1 Image 3­5). Switching off the remote control prevents that unwanted commands are send due to an accidental key press. Furthermore, switching the RCU off will extend the battery life time of the remote control.

R5911443 /09 UDM

33

Pulse Remote Control Unit
To activate the remote control, press the on/off button. To deactivate the remote control, press the on/off button again. Default after (re)placing batteries, is “ON”.
1
Image 3­5
3.4 Using the RCU
Pointing to the reflective screen or IR sensors
Switch on the RCU and point the front of the RCU to the reflective screen surface or point directly to one of the projector IR sensors. Make sure you are within the effective operating distance (30 m, 100 ft in a straight line). The RCU will not function properly if strong light strikes the IR sensor window or if there are obstacles between the RCU and the IR receiver.

Image 3­6
The RCU can also hard-wired been used. See chapter “Using the XLR connector of the RCU”, page 36.
Using the RCU in combination with a 3D emitter
When using a 3D emitter that radiates IR beams (e. g. the optional 3D emitter that Barco provides), the IR beams of the 3D emitter may interfere with the IR communication between projector and the RCU. If such interference occurs, connect the RCU to the projector using the remote cable with XLR connector. It is also be advised to turn the IR receivers of the projector off to avoid the 3D emitter interference. The IR receivers can be turned off in the GUI: System Settings > Communication > IR Control .

34

R5911443 /09 UDM

Pulse Remote Control Unit

3.5 Pulse RCU, Functionality overview

Remote Control Unit buttons

1

2

24

25

26

3

23

4

22

5

21

6

20

7

19

8

18

9

10

11

12

17

13

14

16

15 Image 3­7 1 Button pressed indicator 2 Shutter open 3 Shutter close 4 LCD panel on / off 5 Project OSD on / off 6 Lens zoom 7 Lens shift 8 Menu open / close 9 Menu selection, OK button 10 Menu navigation 11 Input selection 12 Address button 13 Numeric buttons

14 Backspace (while entering values) 15 XLR connector 16 Decimal mark (while entering values) 17 Macro button 18 Menu back 19 Default value button 20 Lens focus 21 RGB filter 22 Test patterns 23 Power on 24 Power off 25 3.5 mm jack 26 RCU on / off

3.6 Pulse RCU, function of the “button pressed indicator”
Functions button pressed indicator
· Rapidly flashes when commands are sent, this is the normal “button pressed” indication. · 1 Short flash when remote control is switched ON by means of the on/off button. · Continuously lit (up to 5 seconds) when address digits are expected after pressing the ADDR button. · Slowly flashes (2 times a second) when the battery level is becoming low; typically when more than 85% of
the useful life is past.

R5911443 /09 UDM

35

Pulse Remote Control Unit
3.7 Pulse RCU, function of the “RGB filter” button
Filtering the color of the projected image
By pressing the RGB filter button on the RCU you can place a color filter on the output of the projector. This feature can be useful during the installation and configuration of a multi-projector or multi-channel setup. By having one projector project a red image and another project a green image, it is easier to spot and adjust the overlap section. By pressing this button multiple times, you will have different active filters, in the following cycle: · Red + Green + Blue (default) · Red only · Green only · Blue only · Red + Green · Green + Blue · Red + Blue · Red + Green + Blue · etc
After powering up, the colors will always revert back to full RGB.
3.8 Displaying and Programming addresses into the RCU
Displaying the Projector Address on the Screen.
1. If the projector is on, press the menu key and navigate to the Status page. The projector address and the broadcast address can be seen under the Communication heading. The projector’s address is displayed on the LCD status screen and / or the OSD.
How to Program an Address into the RCU?
1. Press the Address button until the Button pressed indicator lights up continuously (proximately 5 seconds).
2. Enter the address with the digit buttons within the time the indicator lights up (also proximately 5 seconds). Note: That address can be any value between 0 and 31.
Tip: A few examples: To enter address 3, press “3” digit button on the RCU to set the RCU’s address to 3 and wait until the button pressed indicator is out. Alternatively, you can also press “0” and “3”. This way, the button pressed indicator goes out immediately. To enter address 31, then press “3” and “1” on the digit button on the RCU and the button pressed indicator goes out immediately.
3.9 Using the XLR connector of the RCU
Connecting a cable with the XLR connector will reset the broadcast address of the RCU to its default value ‘0’.

36

R5911443 /09 UDM

How to use the XLR connector
1. Remove the XLR cover by pulling it backwards.

Pulse Remote Control Unit

Image 3­8
2. Connect a cable with XLR plug into the XLR connector of the RCU. 3. Connect the other end of the cable with the XLR input of the projector.
Note: While the XLR cable is connected, the IR beam of the RCU is switched off.
3.10 Using the mini-jack connector of the RCU
Connecting a cable with the mini-jack connector will reset the broadcast address of the RCU to its default value ‘0’.
How to use the mini-jack connector
1. Connect a cable with the mini-jack connector (reference 2 Image 3­9) of the RCU. 2. Connect the other end of the cable with the mini-jack input of the projector.

2
Image 3­9
Note: While the mini-jack cable is connected, the IR beam of the RCU is switched off.
3.11 Pulse RCU, silicone protection sleeve (optional)
Introduction
Barco offers a silicone form fitting protection sleeve for the Pulse RCU. The silicone material keeps it comfortably, non slip and soft touch. All buttons and holes remain accessible. The sleeve is quick and easy installed. For ordering information see Barco website.

R5911443 /09 UDM

37

Pulse Remote Control Unit
How to install
1. Pull off the rubber XLR-lid from the RCU.
Image 3­10
2. Place back side (XLR side) of the RCU into the sleeve and pull the other side of the sleeve over the front side of the RCU.
Image 3­11

38

R5911443 /09 UDM

Input & Communication

4

4.1 Introduction ………………………………………………………………………………………………………………….40 4.2 Local Keypad and LCD panel …………………………………………………………………………………………..40 4.3 LCD touch panel……………………………………………………………………………………………………………41 4.4 Communication connections…………………………………………………………………………………………….42 4.5 LED and Button indication chart………………………………………………………………………………………..44 4.6 Pulse Quad Combo input Mk II …………………………………………………………………………………………45 4.7 Pulse Quad Combo input Mk I ………………………………………………………………………………………….46 4.8 Pulse Quad DP 1.2 input …………………………………………………………………………………………………47 4.9 Pulse SFP input…………………………………………………………………………………………………………….48

R5911443 /09 UDM

39

Input & Communication
4.1 Introduction
General
The Input & Communication module consists of a local keypad with LCD panel (1), a communication panel (4) and a Quad Combo input board (5). The free input slot can be used for optional modules (e.g. the Quad DP 1.2 input board).
Two boards of the same type can be used without restrictions. You can mount a second Quad Combo Input board in the free input slot (6). Alternatively, you can also remove the pre-mounted Quad Combo Input board and replace it with a second optional module (for example, a second Quad DP 1.2 input board).

1

2

3

4 5 6

Image 4­1 1 Local Keypad and LCD panel 2 Optional antenna for WiFi connection 3 Optional antenna for GSM

4 Communication Panel 5 Quad Combo Input board 6 Free input slot (here filled with the Quad DP 1.2 Input board)

4.2 Local Keypad and LCD panel

Overview

12

34 56

Image 4­2

11

10 9

8

7

40

R5911443 /09 UDM

Input & Communication

1 Menu navigation 2 Menu confirmation, OK button 3 Menu open / close 4 Menu back 5 Power on / off 6 Project OSD on / off

7 Input selection 8 Shutter open / close 9 Test patterns 10 Lens adjustment 11 LCD panel

Local Keypad
The Keypad gives direct access to several functions, in addition to access to the menu system.
The keypad has a backlight that can be switched on and off manually. By default the light turns off after 5 minutes.
The Power button and Shutter buttons are equipped with white, blue and red backlit LEDs. The other keys are only equipped with white and blue backlit LEDs. The LEDs are controlled according to the features available.

LCD panel
The LCD panel has two main functions:
1. Showing the menus, the adjustment information and also a mirror of the OSD, (On Screen Display) described in User Interface when this is enabled.
2. Information regarding the status of the projector showing this data: · Projector status · Network address · Active source · Current firmware version · Operation Data · Active functions (Enabled Functions).
Toggle between the two indications by using the Menu button on the keypad, or on the remote control.
The LCD Display will fade out 30 seconds after the last key operation.

4.3 LCD touch panel
The LCD menus can occasionally be slightly different in layout compared with the OSD menu, due to a more optimal layout regarding to the touch functionality of the LCD.
LCD touch panel functionality
In addition to the remote control and the keypad, it is also possible to navigate in the menus with the touch functionality in the LCD panel. Press the icons to select the functions. Select switches to toggle. Select and drag sliders to adjust slider value.

R5911443 /09 UDM

41

Input & Communication
4.4 Communication connections
Communication Panel

12V 1A

12

3

4

5

6

Image 4­3

1 WIFI antenna for wireless IP (optional) 2 12V 1A output 3 Firmware update / USB download log files 4 10/100 base-T for external control over IP and Art- Net 5 DMX interface input 6 DMX interface output 7 XLR input for wired projector control

7

8

9 10 11 12 13

8 RS232 for serial communication 9 Sync Out 3D 10 Sync In 3D 11 Status lights 12 IR receive sensor 13 GSM antenna input (optional)

CAUTION: Ethernet should only be connected to either the 10/100 base-T port (on the communication panel) or the HDBaseT input (on the Quad Combo Input Mk II). Using both at the same time will lead to undefined behavior.

12 V output
12 V output, maximum 1 A, available when projector is not in stand by.
DMX interface
DMX is used as communication bus between different devices in the light technic. Each device has an input and an output, so that the bus can be looped between the different devices. According the standard a five wire cable with XLR connector is used.
You can use the DMX input port to connect a DMX device (DMX console) to the projector. This way you can control the projector from that DMX device (console). The DMX output port can be connected with the next device in the loop.
DMX Pin Description 1 Earth 2 Cold 3 Hot 4 Return – (or not used)
5 Return + (or not used)

DMX
DMX-512 Lighting protocol over RS-485 interface. Carries information of 512 channels from a lighting controller to lighting devices. Standardized by USITT.

RS232/RS422 input
The communication interface of the UDM series projector supports RS232 and RS422 serial communication on two different types of input connectors, a Sub-D connector and an USB connector acting as RS input when connected to an USB input of a PC.
You can use the RS232/RS422 input to connect a local PC to your UDM series projector. By this way you can configure and control your projector from your local PC.

42

R5911443 /09 UDM

Input & Communication
Advantages of using RS232/RS422 serial communication:
· easy adjustment of the projector via PC (or MAC). · allow storage of multiple projector configurations and set ups. · wide range of control possibilities. · address range from 0 to 255. · sending data to the projector (update). · copying data from the projector (backup).
RS232/422 input (Sub-D) port Pin Description 1 DCD : Data Carrier Detect 2 RXD- : Receive Data 3 TXD- : Transmitted Data 4 DTR : Data Terminal Ready [RS232] / TXD+ : Transmitted Data [RS422] 5 GND : Ground 6 DSR : Data Set Ready [RS232] / RXD+ : Received Data [RS422] 7 — (not connected) —
8 CTS : Clear To Send 9 RI : Ring Indicator
RS232 An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the communication path between two devices using either D-SUB 9 pins or D-SUB 25 pins connectors. This standard is used for relatively short-range communications and does not specify balanced control lines. RS-232 is a serial control standard with a set number of conductors, data rate, word length and type of connector to be used. The standard specifies component connection standards with regard to computer interface. It is also called RS-232-C, which is the third version of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. Logical ‘0’ is > + 3V, Logical ‘1’ is < – 3V. The range between -3V and +3V is the transition zone.
RS422 An EIA serial digital interface standard that specifies the electrical characteristics of balanced (differential) voltage, digital interface circuits. This standard is usable over longer distances than RS232. This signal governs the asynchronous transmission of computer data at speeds of up to 920,000 bits per second. It is also used as the serial port standard for Macintosh computers. When the difference between the 2 lines is < – 0.2V that equals with a logical ‘0’. When the difference is > +0.2V that equals to a logical ‘1’..
USB port
The communication interface is equipped with a master USB port, type “A” connector. This USB port will simplify the service procedures for firmware updates or for downloading the log files without a network connection.
If the only file on the USB device is the firmware file (a “*.fw” file), the projector will automatically start one of the following processes.
· cornet.fw: The projector will upgrade or downgrade, depending on the version number. · LogExtractor.fw: The log files will be downloaded.
Make sure that any used USB-stick is FAT32 compatible and contains no other files or folders.

R5911443 /09 UDM

43

Input & Communication

4.5 LED and Button indication chart

Button Backlight Status
Button Power button
Shutter button

Color status Blinking WHITE (slow) Blinking WHITE (fast) Solid WHITE
Blinking BLUE Solid BLUE Blinking RED Off (no color)
Solid WHITE Solid RED

Description Projector starts up (booting)
Firmware upgrade
Projector is in Standby or Ready mode Projector goes to ON mode
Projector is ON
Error condition
Projector is OFF, starts up, or is in Standby or Ready mode.
Projector is ON, shutter is open
Projector is ON, shutter is closed

LED Status

12V 1A
LED PWR (power LED) LIGHT (Illumination LED)
ERR (error LED) IR

Color status Off RED ORANGE GREEN Off RED ORANGE GREEN GREEN-ORANGE Off RED toggles on/off ORANGE toggles on/off
RED GREEN

Description Projector powers up Projector is in Standby mode Projector is in Ready mode Projector is on Light source is off No light source detected Light source is on in ECO mode Light source is on in normal mode Light source is on in CLO mode No error Error Warning
IR signal received IR signal acknowledged

44

R5911443 /09 UDM

4.6 Pulse Quad Combo input Mk II
Overview Quad Combo Input Mk II

Input & Communication

1

2

3

4

Image 4­4

1 Quad SDI channel A: 3G/12G input 2 Quad SDI channel B: 3G input 3 Quad SDI channel C: 3G SDI input + 3G/12G output 4 Quad SDI channel D: 3G SDI input / output

5

6

7

8

5 DisplayPort Input 6 HDMI input 7 HDBaseT input 1 8 HDBaseT input 2

Functionality of the Quad Combo input Mk II
The Quad Combo Input Mk II support 12G input and throughput on the SDI connectors.
Compared with the Mk I the Mk II includes the following:
· SDI input A supports 12G input signals. · SDI input C functions as a loop- through output for any signal placed on input A. · SDI input D functions as a loop-through output for any signal placed on input B. · HDBaseT input 1 supports network connectivity.

CAUTION: Ethernet should only be connected to either the 10/100 base-T port (on the communication panel) or the HDBaseT input (on the Quad Combo Input Mk II). Using both at the same time will lead to undefined behavior.

SDI input & output ­ How does it work?
When connecting an SDI source to the projector and the signal is HD or 3G, you can choose any of the four input connectors.
When connecting multiple projectors with the same signal, you can connect the signal as follows:
· Connect the source signal to Input A or B of the first projector. · If the source signal is connected to input A, connect input/output C to the Input of the following projector. · If the source signal is connected to input B, connect input/output D to the Input of the following projector. · Continue in the same fashion until all projectors are connected.
When connecting a 12G SDI source to the projector, you can only connect that source to input A.
Only Input A accepts 12G SDI signals . While it is technically possible to connect a 12G SDI source to Input B and connect that source to another projector in line (using Input/Output D), this first projector itself will not be able to process the 12G signal.

R5911443 /09 UDM

45

Input & Communication

A HD, 3G & 12G

IN 0 N.C. IN 1

OUT 0 OUT 1

HD & 3G

B

IN: HD & 3G

C

OUT: HD, 3G & 12G

IN 0 N.C. IN 1

OUT 0 OUT 1

SDI IN/OUT N.C. SDI OUT

OUT 0 IN 0

FPGA

IN: HD & 3G

D

OUT: HD & 3G

SDI IN/OUT

OUT 0

Image 4­5

N.C. SDI OUT

IN 0

LED behavior
· The SYNC LED lit up ORANGE when valid input sync is detected. · The SEL LED lit up GREEN when the input is selected. · The SEL LED blinks GREEN when the input/output is selected and configured as output.

For specifications about the supported inputs for SDI, HDMI, HDBaseT and DisplayPort 1.2 see chapter “Specifications”, page 179.

4.7 Pulse Quad Combo input Mk I

Overview Quad Combo input Mk I

SDI IN SEL

SDI IN/OUT

SEL

SEL

SEL

SEL

SEL

SEL

SEL

SYNC

SYNC

SYNC

SYNC

A

B

C

D

SYNC

SYNC

DP

SYNC HDMI SYNC HDBT1

HDBT 2

1

2

3

4

Image 4­6

1 Quad SDI channel A: 3G input 2 Quad SDI channel B: 3G input 3 Quad SDI channel C: 3G input 4 Quad SDI channel D: 3G input

5

6

7

8

5 DisplayPort Input 6 HDMI input 7 HDBaseT input 1 8 HDBaseT input 2

LED behavior
· The SYNC LED lit up ORANGE when valid input sync is detected. · The SEL LED lit up GREEN when the input is selected.

For specifications about the supported inputs for SDI, HDMI, HDBaseT and DisplayPort 1.2 see chapter “Specifications”, page 179.

46

R5911443 /09 UDM

Input & Communication

Remark concerning the Mk I and Mk II inputs boards
The Mk I input board miss functionality that has been implemented on the Mk II input board. These missing features include:
· Loop-through functionality · 12G SDI support · Network connectivity on HDBaseT inputs
The projector is now standard equipped with the Mk II input board. For details and specifications see chapter “Pulse Quad Combo input Mk II”, page 45.
Visual difference between the Mk I and Mk II input boards
There is one real visual aid to tell the two variants apart. There are visual markings added on the Mk II input board, marking which connector supports 12G and which only supports 3G.

SDI IN SEL

SDI IN/OUT

SEL

SEL

SEL

SYNC

SYNC

SYNC

SYNC

1

A

B

C

D

Image 4­7 Quad Combo Input Mk I board, without markings above the SDI inputs

SDI IN

SDI IN/OUT

3G/12G SEL

3G

SEL

3G

SEL

3G

SEL

SYNC

SYNC

SYNC

SYNC

2

A

B

C

D

Image 4­8 Quad Combo Input Mk II board, with 3G/12G markings above the SDI inputs/outputs.

4.8 Pulse Quad DP 1.2 input
Quad DP 1.2 input

1

2

3

4

Image 4­9

1 Quad DisplayPort channel A input 2 Quad DisplayPort channel B input 3 Quad DisplayPort channel C input 4 Quad DisplayPort channel D input

LED behavior
· The SYNC LED lit up ORANGE when valid input sync is detected. · The SEL LED lit up GREEN when the input is selected.

For specifications about the supported inputs for DisplayPort 1.2 see chapter “Specifications”, page 179.

R5911443 /09 UDM

47

Input & Communication

4.9 Pulse SFP input
The Barco SFP Input Board has been designed and tested to work alongside the Barco SFP Output Board. However, it is possible that the SFP Input board can also work with other third-party devices that support 12G over fiber. Due to the many third-party options available on the market, the input board could not be tested for every option available.
Overview SFP input
The SFP Input board is used to connect 12G SDI over fiber. The SFP input is delivered without any connector. It is up to the customer to buy the necessary connectors, transceivers and cables. These parts can be mounted on the indicated places on the front panel of the board.

SEL

SEL

SYNC Opt A

SYNC Opt B

1

2

Image 4­10

1 Neutrik Duo optical connector or Neutrik Quad optical connector 2 Neutrik Duo optical connector or Neutrik Quad optical connector 3 2x12G SDI/10GE transceiver

SFP A
3

SFP B

For specifications about the supported inputs for SFP see chapter “Specifications”, page 179.

LED behavior
· The SYNC LED lit up ORANGE when valid input sync is detected. · The SEL LED lit up GREEN when the input is selected.
Use cases
The SFP can be configured as follows: 1. SFP+ transceiver + Fiber connection (integrated or separated) 2. Neutrik OpticalCon Duo + SFP+ transceiver + internal fiber 3. Neutrik OpticalCon Quad + SFP+ transceiver + internal fiber 4. Loop-through mode
See projector installation manual for detailed instructions on how to install/configure the SFP input.

WARNING: Only by Barco trained and qualified technicians are allowed to install the SFP input.

Optical Tranceiver to comply with Laser Class 1, IEC60825­1: 2014

48

R5911443 /09 UDM

GUI ­ Introduction

5

5.1 Overview …………………………………………………………………………………………………………………….50 5.2 Navigation……………………………………………………………………………………………………………………53 5.3 Test Patterns ………………………………………………………………………………………………………………..55
About this chapter
This chapter gives an general overview of the Graphic User Interface.

R5911443 /09 UDM

49

GUI ­ Introduction
5.1 Overview
Disclaimer on GUI images used in this manual
The GUI images in this manual are example illustrations and should be treated as such. While the name of the projector displayed in the illustrations may be different from the projector model you are currently using, the menu lay-out and functionality is identical.
GUI ­ First start of the software
When you start the projector for the first time, you will be requested to choose the system language. You can choose between the following languages:
· German (DE) · English (EN-US) · Spanish (ES) · French (FR) · Japanese (JA) · Korean (KO) · Portuguese (PT-BR) · Russian (RU) · Chinese (ZH)

Image 5­1 Example of the welcome screen
Once you confirmed your choice, you will be prompted with the Pulse product- specific End User License Agreement (EULA). You will only be able to access the projector software once you have fully read and approved the EULA.
GUI ­ Product Registration
Upon first startup you will be requested to register the projector. You can perform the registration procedure now, or choose to Register Later. For more information on the entire registration procedure, refer to the Projector Registration user guide.

50

R5911443 /09 UDM

GUI ­ Introduction
Image 5­2 Example of the Product registration form
GUI ­ Status Screens
While the projector menu is not active, or the projector is Ready or Standby mode, the Status screens remain visible. These screens give an overview of the state of the projector and can be navigated through using the left and right arrow keys, or by swiping the screen left or right. The status screens are the following: · Dashboard: The main overview. This screen displays all the chosen options on the projector (chosen
source, blending/masking, display mode, etc). · About: General info about the projector. This includes serial number, software version, mounted lens and
light source runtime. It also includes altitude, and the pitch and roll tilt angles. · Notifications: The error and/or warning messages that are currently active. If no messages are active, this
list will be empty. · Preview: A preview pane of the projected image. If no image is being projected, a test image is displayed
instead.

Image 5­3 Example of a Dashboard status screen
GUI ­ Main Menu overview
The projector on-screen display (OSD) is the primary user interface (UI). From here, you can review and adjust all projector and display settings. The OSD interface uses buttons to display the main menu. Each main menu contains submenus.

R5911443 /09 UDM

51

GUI ­ Introduction The OSD can be disabled by pressing the OSD on/off button.
Image 5­4 Example of the home menu
The projector software platform uses access levels what each user can do. A standard user has access to the standard projector functionality. A certified service technician has also access to the advanced settings menu. This menu is password protected. This password can only be obtained by following the service partner training.

52

R5911443 /09 UDM

GUI ­ Introduction

GUI ­ Pulse software menu tree

Source

Image

Installation

Lx Quad combo Connector x Quad SDI
Connector settings Lx Quad DP
Connector x Stitched options Connector settings Lx SFP Input
Connector x Connector settings

Contrast Brightness Saturation Sharpness
Gamma Digital zoom
and shift Advanced Settings
Realcolor P7 Output resolution
HDR Dynamic black

Laser ranging
Motorized frame Center motorized
frame (action) Orientation
Scaling
Illumination
3D
Z-axis calibration
Lens Zoom & focus
Shift Dynamic focus
(on/off) Shift to center
(action) Tilt sensor

Profiles
Profile Edit New Profile
Assign profile x to preset (action) Delete profile x
(action)
Profile x (activate)

Settings
Product registration Date and time³ Standby mode Lens features
Communication Remote control Host name LAN HBaseT WiFi DMX GSM Cloud services Regulatory information

Test patterns
Test pattern x
Custom test pattern y Warped test pattern Off

Status
Status screen About

Warp Warp (on/off) Screen size 4 corners Bow Warp files Transport delay

Blend and mask Basic blend Blend mask Black level Blend files
Black level files

User interface Language Themes Units Backlight

System
Cooling mode
Operational mode Capture mode (on/off)
General Open source license list

Maintenance
Factory reset
Lens calibration
Frame calibration
Flex Electronic convergence Login to advanced settings

Advanced settings
Native RealColor
Statistics
Laser banks
Tilt sensor calibration
Remote access Source preview (on/off) Camera preview (on/off)

Image 5­5 Menu tree of the Pulse software, with the following footnotes

1 Only visible if specific option is installed

5

2 Only visible on 4K models with actuators

6

3 Only visible on UDX & UDM

7

4 Only visible on UDM

Only visible on HDX4K Only visible when motorized lens is installed Only visible when logged in as service user

5.2 Navigation
Navigation via the RCU or local keypad
Navigating the OSD can be done using the remote control or the local keypad.

R5911443 /09 UDM

53

GUI ­ Introduction

1

23 4

32

14

Image 5­6
To start up the menu structure, press MENU (1). Use the arrow keys (Menu Navigation buttons) to navigate to the desired menu item (2). The background color changes to light blue. Press the Menu Selection button (center key of the arrow keys), also called OK button, to activate that item and to jump one level deeper (3). Use the numeral keys to enter values, or use the arrow keys to move the bar scale up or down. Press the Back button to go up one level (4).

Image 5­7 Example of the home menu
Remark: a blue slider bar on the right side of the window means that there are more items to show than those currently displayed.
Define values
Menu settings are displayed using check boxes, bar scale sliders, and drop- down lists.
To set a value:
· Press OK to select or deselect a checkbox (turn a function ON or OFF). · Use the arrow keys to move the bar scale slider up or down on the value line. For a bar scale 0-9, each
step will equal 10% of the total value. · To enter the value as a direct number, press OK, input the digit(s), and then press OK again to execute and
exit cursor mode e.g. OK 79 OK. Within an input field, use the * button as backspace button to remove an entered digit. Use the # button to enter a dot (.).
Changes to values are implemented dynamically.

54

R5911443 /09 UDM

GUI ­ Introduction
To enter values with the local keyboard, use the arrow keys to select the first digit, press OK. Select the second digit and press OK. Continue until all digits are entered. Close the action by selecting the enter () button and press OK. Select the backspace button and press OK to remove the last entered digit.
Using the LCD touch display
From Pulse software 2.0 onward, the touch display functionality of the LCD panel has been activated and can be used. Instead of using the remote control buttons or keypad keys or button, you can now: · Touch menu icons to enter the respective menu. · Swipe a menu up and down if not all information is not immediately visible (e.g. more than 8 (sub)menu
icons being visible) · Return to a higher menu level, by touching the blue name in the top left corner of the display. · Use touch functionality to use menu items (check boxes, sliders, digital keyboard or keypads, etc). · Swipe menu panes left or right when multiple panes are available (e.g. the Status menu)
Menu memory
The OSD menu remembers the last selected sub-item as long as the projector is running. The menu memory is reset when restarting the projector from standby.
5.3 Test Patterns
List of standard test patterns
The test patterns that are available by default are the following: · Aspect · Focus-Green · Focus-bursts · White / Black/ Red / Green / Blue · Cyan / Magenta / Yellow · Color bars · Color gradients · Checkerboard · Cross hatch · Geometry · Horizontal gray bars · Vertical gray bars · 3D Stereo
About the test pattern types
There are three types of test patterns possible in the projector:

R5911443 /09 UDM

55

GUI ­ Introduction

Type Standard test patterns

Explanation
Standard test patterns. See previous list to see all test patterns available for your device.

Example of test pattern icon

Warped test patterns

Available from software 2.2 onward. Every test pattern will have a “warped” variant available, symbolized with a “warp” symbol on the top-left corner of the icon.
If active and configured, the warping will be applied to this test pattern. If warping is not active, or not configured, this will be identical to the standard test pattern.

Custom test patterns

If uploaded via an external tool, you will find your custom uploaded test patterns (and its warped variant) at the bottom of the list of available patterns.
All custom uploaded test patterns will be marked with the default “test pattern file” icon.

How to use test patterns
1. In the main menu, select Test Patterns.
or Push the Test Patterns button on the RC.

Image 5­8 Main menu, Test patterns
2. In the Test pattern menu, select the desired test pattern from the list. 3. To turn the test pattern off, select off instead.

Image 5­9 Test patterns menu, test pattern off

56

R5911443 /09 UDM

GUI ­ Source

6

6.1 Displaying a single source ……………………………………………………………………………………………….58 6.2 Displaying multiple sources: Stitched layouts ……………………………………………………………………….58 6.3 Connector settings…………………………………………………………………………………………………………60
About the Source menu
This menu is used to select, review and configure sources into the projector.

R5911443 /09 UDM

57

GUI ­ Source
6.1 Displaying a single source
About selecting a source
Before a source can be projected, the source signal must be connected to the source input(s) of the device and a valid synchronization signal must be available along with the source signal on at least one of the input connectors.
How to select?
1. Press Menu to activate the menus and select Source.
Image 6­1 Main menu, Source
2. Press OK. The Select Source menu is displayed with the actual available sources filled out.

Image 6­2 Example of the input selection menu
3. Select the desired input.
6.2 Displaying multiple sources: Stitched layouts
About stitched layouts
The first time you use a selected single source, the source will be displayed in the projector’s native resolution. If the resolution of the source is different to the projector’s resolution, the image is stretched or shrunk. It is however possible to configure and display two or four source signals to make up one single image in full native resolution. This is called a Stitched Layout: the sources are stitched together. The following table lists which stitched layouts you can use, and in which display mode these layouts can be used.

58

R5911443 /09 UDM

GUI ­ Source

The table below describes the different Stitch Layouts and scan directions.

Type of layout
1
: Single
12

Description

Available connectors

A single source is displayed in Quad Combo input:

full screen

· SDI (4x)

· HDBaseT (2x)

· DisplayPort

· HDMI

Quad DP 1.2 Input:

· DisplayPort (4x)

Two inputs are required. The Quad DP 1.2 Input: sources are displayed next to · 2x DisplayPort each other.

Mode Mono / Active stereo
Mono / Active stereo

: Dual 1 x 2
12
34
: Quad 2 x 2
1234

Four inputs are required. The sources are displayed in four quadrants.

Quad Combo input: · 4x SDI input
Quad DP 1.2 Input: · 4x DisplayPort

Four inputs are required. The Quad DP 1.2 Input: sources are displayed next to · 4x DisplayPort each other.

Mono / Active stereo
Mono / Active stereo

: Quad 1 x 4

Two inputs are required. The Quad DP 1.2 Input:

sources are displayed one · 2 x DisplayPort

1

above the other.

Passive stereo

: 2 x single

Four inputs are required. Two Quad DP 1.2 Input:

sources are displayed next to · 4x DisplayPort

12

each other, while the other two are displayed above the first

: 2 x Dual 1 x 2 two

Passive stereo

Even if passive stereo sources are selected, the output of this projector can only be in either 2D or in Active Stereo. Advanced image processing will make sure a passive stereo image is properly converted to active stereo.

How to select a stitched layout
1. Press Menu to activate the menus and select Source.

Image 6­3 Main menu, Source
2. Press OK. The Select Source menu is displayed with the actual available sources filled out, including all available stitched layout options.

R5911443 /09 UDM

59

GUI ­ Source

Image 6­4 Example of the stitched layout options
3. Select the desired stitched input. Tip: If the Quad DP input board is installed, scroll all the way down the menu for the stitched options on that board.

Image 6­5 Example of the stitched input options with the Quad DP board installed
6.3 Connector settings
About connector settings
The Connector Settings menu allows you to change settings for each input connector of the projector. By default all options for every connector are set to automatic, together with the native Extended Display Identification Data (EDID). When entering the menu for each input connector, you can change the following: · Color Space · Signal Range · EDID
How to configure a connector
1. Press Menu to activate the menus and select Source.

60

R5911443 /09 UDM

GUI ­ Source
Image 6­6 Main menu, Source
2. Press OK. The Select Source menu is displayed with the actual available sources filled out.
3. Scroll down to the bottom of the list of available sources and select Connector settings.
Image 6­7 Source menu, connector settings
The available input connectors are displayed.

Image 6­8 Example of the Connector settings menu
4. Select the desired connector. The connector settings menu for the selected connector will be displayed.

Image 6­9 Example of connector settings for one of the connectors

R5911443 /09 UDM

61

GUI ­ Source
5. You can change the following: · To force a limit on the used signal range, select one of the available signal ranges. · To force a limit on the color space, select one of the available color spaces. · To set a video timing other than the one native for the connector, select one of the options under EDID. Note: You cannot change the EDID for SDI connectors.

62

R5911443 /09 UDM

GUI ­ Image

7

7.1 Setting image levels manually…………………………………………………………………………………………..64 7.2 Adjusting the sharpness ………………………………………………………………………………………………….65 7.3 Adjusting the gamma correction………………………………………………………………………………………..66 7.4 Setting the desired Gamma type ……………………………………………………………………………………….67 7.5 Digital shift & zoom ………………………………………………………………………………………………………..69 7.6 RealColor P7………………………………………………………………………………………………………………..73 7.7 Displaying HDR content ………………………………………………………………………………………………….75 7.8 Dynamic contrast…………………………………………………………………………………………………………..76

R5911443 /09 UDM

63

GUI ­ Image
7.1 Setting image levels manually
Purpose
Contrast: Change the contrast of the complete output signal of the projected image. Brightness: Change the brightness of the complete output signal of the projected image. Saturation: Change the saturation of the complete output signal of the projected image.
How to set up Contrast
1. In the main menu, select Image Contrast.
Image 7­1 Image menu — Contrast
2. Use the or key to change the contrast enhancement until the desired value is reached (adjustable between 0 and 2).

Image 7­2 Example of the image sliders, contrast is the first slider
3. If necessary, use the or key to select the other image adjustment options.
How to set up Brightness Level
1. In the main menu, select Image Brightness.

Image 7­3 Image menu — Brightness
2. Use the or key to change the brightness until the desired value is reached (adjustable between ­1 and 1).

64

R5911443 /09 UDM

GUI ­ Image

Image 7­4 Example of the image sliders, brightness is the second slider
3. If necessary, use the or key to select the other image adjustment options.
How to set up Saturation Level
1. In the main menu, select Image Saturation.
Image 7­5 Image menu — Saturation
2. Use the or key to change the saturation until the desired value is reached (adjustable between 0 and 2).

Image 7­6 Example of the image sliders, Saturation is the third slider
3. If necessary, use the or key to select the other image adjustment options.
7.2 Adjusting the sharpness
About adjusting the sharpness
The sharpness adjustment amplifies the high frequency components in the picture. This means that by increase the sharpness, the picture will be perceived as sharper, and if decreased, the picture will be perceived as more blurry.

R5911443 /09 UDM

65

GUI ­ Image Increasing the sharpness will have the best effect in high contrast images, eg a table with text and borders. In a natural picture, high sharpness can be perceived as noise, as all details in the picture will be amplified. Available range: -2 to 8. Default value: 0
Image 7­7 Effect of sharpness adjust
How to adjust
1. In the main menu, select Image Sharpness.
Image 7­8 Image menu ­ Sharpness
2. Use the or key to change the sharpness until the desired value is reached.

Image 7­9 Example of the image sliders, Sharpness is the bottommost slider
3. If necessary, use the or key to select the other image adjustment options.
7.3 Adjusting the gamma correction
About gamma correction
Gamma correction is an image quality enhancement function that offers a richer image by brightening the already darker portions of the image without altering the brightness of the brighter portions (contrast feeling enhanced).
How to adjust
1. In the main menu, select Image Gamma.

66

R5911443 /09 UDM

GUI ­ Image
Image 7­10 Image menu ­ Gamma
2. Use the key to select the slider. 3. Use the or key to change the gamma value between 1.0 and 2.8 . The default value is 2,2.
Tip: The slider can be adjusted with a precision of 0.1.

Image 7­11 Example of the gamma menu
7.4 Setting the desired Gamma type
About the alternate gamma types
Next to the standard gamma correction, the projectors can be manipulated in a way to simulate gamma types for other devices or purposes. This includes sRGB (standard Red-Green-Blue), Power gamma, DICOM gamma ranges and for simulation projectors sim1.
DICOM gamma ranges are usually reserved for medical displays. While this projector is not a certified DICOM display, it can simulate certain specific DICOM gammas at a few selected max light outputs. The DICOM gamma assumes that both ambient light and the projector outputs black as 0 cd/m². Then there will be a few predefined gamma curves at the following light outputs:
· DICOM 10: 10 cd/m² · DICOM 60: 60 cd/m² · DICOM 180: 180 cd/m² · DICOM 250: 250 cd/m² · DICOM 300: 300 cd/m² · DICOM 400: 400 cd/m²
This is the full list. Take into account that the available DICOM gamma types for your projector type may be more limited than this list.
Exception when using an HDR source
The only alternate color gamma that can not be selected in this menu is PQ/HDR. Because the color output of HDR is dependant on extra factors such as screen luminance, a separate menu has been made available for this (PQ).

R5911443 /09 UDM

67

GUI ­ Image
If the source signal is HDR encoded an HDR icon will be visible next to the source signal. This is visible both in the Source selection menu, as well as the status menu.

Image 7­12 Example of the HDR icon on the status menu
For more info on PQ and HDR, refer to “Displaying HDR content”, page 75.
How to adjust the gamma type?
1. In the main menu, select Image Gamma type.
Image 7­13 Image menu ­ Gamma
The Gamma type menu is displayed. If source content is available, the detected gamma of the source will be displayed at the bottom of the menu.

Image 7­14 Example of the gamma menu
2. Use the or key to select the desired gamma type and confirm.

68

R5911443 /09 UDM

GUI ­ Image

Image 7­15 Example of selecting a gamma type
Tip: If not sure what gamma type to select, keep the default value auto selected. This automatic mode will determine the used gamma type based on the incoming signal. However: keep in mind when using the automatic mode, your media player needs to be configured correctly as well. While most mainstream media player devices will be configured correctly by default, we cannot guarantee this is the case for every device available on the market. If you notice the projected image seems “off”, it may be necessary to check the configuration of your media player. For more info, check the user guide of your media player device.
7.5 Digital shift & zoom
What can be done?
The image can be optically shifted by using the vertical and horizontal lens shift. If you want to reach a lens shift beyond what is possible with the optical shift, you can also perform a digital lens shift. This digital shift will occur on the DMD, rather than the lens holder. So take into account that this additional shift is minimal and restricted to the limits of the chip used. For the optical zoom and len

References

• HHS Accessibility & Section 508 | HHS.gov
• Inspired sight and sharing solutions - Barco
• Patents - Barco
• Support - Barco
• Support - Barco
• Inspired sight and sharing solutions - Barco

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>