PREMIUM LEVELLA PRF315300HW Defrost Top Freezer Mini Refrigerator Instruction Manual
- June 9, 2024
- PREMIUM LEVELLA
Table of Contents
PRF315300HW Defrost Top Freezer Mini Refrigerator
Instruction Manual
Service manual
Model: PRF315300HW
PRF315300HW Defrost Top Freezer Mini Refrigerator
| BRAND: | Pjq¡¡u¡ Lqvqllp |
|---|---|
| MODEL: | PRF315300HW |
| PRODUCT DESCRIPTION: | M¡µ¡ Bpj, glp33 3hqlvq3, cjy3Ępl cj¡3pqj, jqcq33qd |
hpµdlq
Coloj| White
LOADING QTY/4OHQ| 274
PRODUCT DIMENSION (WDH mm)| 48O5OO85O
PACKING DIMENSION (WDH mm)| 5OO54O885
PRODUCT WEIGHT (Kg):| Gjo33 Wq¡ghĘ (G.W)| NqĘ Wq¡ghĘ (N.W)
26| 24
ToĘpl Gjo33 Cpppc¡Ęy (Cu.FĘ)| 87
ToĘpl NqĘ Cpppc¡Ęy (Cu.FĘ)| 85
The cooling system
General exploded view
| No. | stoma Code | Description of Spare Part | Quantity |
|---|---|---|---|
| 4 | 20122080036 | Door hinge screw cover | 1 |
| 5 | 20122080091 | Door hinge cover | 1 |
| 6 | 3031400148 | Upper door hinge | 1 |
| 7 | 2208101188 | Middle hinge washer | 1 |
| 8 | 3031400116 | Middle door hinge | 1 |
| 9 | 3031400067 | Lower door hinge | 1 |
| 10 | 2100152587 | Upper door | 1 |
| 10.1 | 30204430145 | Upper door gasket | 1 |
| 10.2 | 20122090005 | Right Aid Closer Of Upper Door | 1 |
| 10.3 | 20122090011 | Left Aid Closer Of Upper Door | 1 |
| 11 | 2100152588 | Lower door | 1 |
| 11.1 | 3020400146 | Lower door gasket | 1 |
| 11.2 | 3031500031 | Door joist, straight | 1 |
| 11.3 | 3031500044 | Door joist, curved | 1 |
| 11.4 | 3031500011 | Lower door joist | 1 |
| 11.5 | 20122090162 | Right Aid Closer Of Lowe Door | 1 |
| 12.6 | 20122090179 | LeftAid CloserOf Lower Door | 1 |
| 12 | 2501100002 | Door switch | 1 |
| 13 | 20120020226 | Ridge shelf assembly | 1 |
| 17 | 3031500055 | Botde rack for drinks | 1 |
| 18 | 3020500092 | Upper door joist | 1 |
| 19 | 2207400523 | Crisper drawer assembly | 1 |
| 20 | 20120030010 | Cover of crisper drawer | 1 |
| 21 | 3050100117 | Power supply cord | 1 |
| 22 | 3039900264 | Compressor bracket | 1 |
| 25 | 20122990039 | Drain pan | 1 |
| 26 | 3050200095 | Earthing wire of compressor | 1 |
| 28 | 2400100282 | Compressor | 1 |
| 29 | 3040500011 | Drier filter | 1 |
| 30 | 20114070006 | Connecting tube | 1 |
| 31 | 3040600005 | Process tube | 1 |
| 32 | 20120010085 | Thermostat controller | 1 |
| 32. | 2400200005 | Thermostat | 1 |
| 32. | 20122010037 | Thermostat Knob | 1 |
| 32. | 2500500002 | Light Bulb | 1 |
| 33. | 20122010002 | Controller Shell | 1 |
| 33. | 20122010048 | Lamp Cover | 1 |
| 33. | 2500600001 | Light Holder | 1 |
| 42 | 20122990019 | Higher Leveling Foot | 1 |
| --- | --- | --- | --- |
| 44 | 20122990006 | Shorter Leveling Foot | 1 |
| 300 | 2700501337 | Trademark | 1 |
| 301 | 2700117929 | Carton | 1 |
Trouble shooting guide
| No | Problem | Possible Cause | What To Do |
|---|---|---|---|
| 1 | Refrigerator room temperature Ok and compressor running Fan not working |
Freezer room temperature not enough cold
No air in the freezer air outlets| the fan motor failure| I- Open the cover
board of the air duct in the freezer room and check the fan
2-If not running. measure the voltage between the red wire and black wire of
fan
3-If the voltage is 12V, the fan motor is failure and replace it with a new
one
the failure of the inner wire to fan connector| 1-Measure Me voltage between
the CN2 red and black wire of PCB
2-If the voltage is 12v. check from the inner wire to fan connector
the PCB failure| 1-Measure the voltage between the CN2 red and black wire of
PCB
2-If the voltage is zero. then the PCB failure and change a new PCB
.)
2| No defrost
Freezer room temperature* not cold enough
Refrigerator room- duct and ice formation on the evaporator| the drainpipe
contains impurity| 1-Disconnect power, and let the ice melt and
drain pipe the
2-2 If not. check if there is impurity and dean
the drain pipe
the sensor failure a PCB failure| 1-Check the fuse
2-If the fuse is melted, it means that the sensor failure or PCB failure
3-Change the sensor or PC
the defrost heater is broken or PCB failure| 1-Check the CN4 defrost heater
two oonnector
2-If the heater is OK then is the PCB failure and change the PCB
3| The temperature of the freezer and refrigerator is not cold enough
The temperature can not be adjusted by the potentiometer (thermostat)| the
potentiometer failure| 1-Inspect the potentiometer (thamoStan
2-Measure the resistance value by adjusting the potentiometer (thermostat)
3-The resistance value is not changed by adjusting the potentiometer
(thermostat)
the sensor failure| 1-If the potentiometer (thermostat) setting is below 3
degrees. the compressor will be running 20 minutes and then stop 30 minutes
2-If the potentiometer (thermostat) setting is more than 3 degrees. the
compressor will be running 30 minutes and then stop 20 minutes
3-If the compressor works like the above situation. it means the sensor
failure
4-Open the back of the refrigerator and change the sensor of the refrigerator
evaporate
4| LED light is not worlung| the led failure| 1-Open the refrigerator door and
measure the voltage of CN3 in the PCB
2-If dae voltage is zero then it means the connecting wire failure
3-If the voltage is 12V. it means the led failure
---|---|---|---
the switch circuit failure| 1-If the CN3 voltage is not 12V. then check the
CN4 voltage
2-If the CN4 voltage is not changed by clovng and opening the door. it means
the switch circuit failure
s| Compressor not start running| no problem| 1-The time between two starting
is shorter than 12min
2-The refrigerator room temperature is lower than the set temperature
3-In this case. it is no problem. Please wait for longer
PCB failure| PCB has automatic self-examination
1-Open the cover of PCB at the back Of the product. plug-in power and Puth the
$W101. switch 3 seconds and the PCB begin
automatic self-examination program
2-Then the led. compressor. fan and defrost heater will work for two seconds
and then stop and quit the automatic self-examination program. After that. the
program will reset to the original setting
3-If the automatic self-examinant:0 program is not working. it means the PCB
failure and needed to be changed
compressor wire failure or compressor damage| 1-Measure the voltage of
compressor input connector
2-If it is OK then check the starting and relay of the compressor
3-Also check the wire if it Es OK
6| Not woeldng at all| the PCB failure| 1-Check the power by multimeter
2-If Me input voltage is 220V-240V. but the led. COmPressor fan. and defrost
heater are all not working. it means the PCB failure and needed to be changed
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>