MCOCOD DSO1 Double Sliding Frameless Shower Door in Brushed Instruction Manual
- June 9, 2024
- MCOCOD
Table of Contents
DSO1 Double Sliding Frameless
Shower Door in Brushed
Instruction Manual
DSO1 Double Sliding Frameless Shower Door in Brushed
PARTS LISTING
DSO1
NO.| Name| Picture| Qty| NO.| Name|
Picture| Qty
---|---|---|---|---|---|---|---
1| Sliding Glass| | 2| 10| Middle Seal| | 2
2| Guide Rail| | 1| 11| Anti-Splash Threshold| | 1
3| Roller| | 4| 12| BmmWall Plug| | 4
4| Anti-jumping knob| | 4| 13| Screw ST5x40| 
| 4
5| Wall Bracket| | 2| 14| Screw ST4x30| | 1
6| Anti Collision Block| | 4| 15| 6mmWall Plug| | 1
7| Guide Block| | 1| 16| Punch Template| | 1
8| Towel Bar| | 2| 17| Allen Key| | 1
9| Side Seal| | 2| | | |
PARTS LISTING
**NOTES BEFORE INSTALLATION**
- Prepare the tools. (Please refer to page 5)
- All measurements and installation should do after the wall is completed.
- Make sure the bottom is horizontal and the wall is vertical, if the bottom is not horizontal or the wall is not vertical, please contact our installation technical support.
- Understand the names and uses of individual accessories of shower doors. (Please refer to page 1~3)
- Installation by licensed professional contractor is recommended.
- Please watch installation video or call us for installation support. ( Installation Video: http://wsc.fit/Sjh)
- To stretch width or cut the guide rail, Please contact us first to install technical support.
- Do not remove the glass protective corner during installation.
- Tile walls are best to replenish some glass glue at the tile seams to avoid leakage after the installation is completed.
TOOLS REQUIRED
(Please bring your own tools)
|
---|---
(we offer)
Aluminum punch template| Spirit level
|
Tape measure| Power Drill
|
Screw driver| Drill Bits 5/16″ & 1/4″
|
Pencil| Rubber hammer
|
Hacksaw| Silicone Gun Modified Silane(Silyl) Polymer
INSTALLATION STEPS
*Technical
support number
626-890-3620
321-946-6293
-
According to the assigned aluminum punching template (please measure with horizontal ruler), draw the punching point position after ensuring the slope value.
-
Drill the holes according to the drawn holes, making sure that there is no offset of the holes. The drilling positions of the left and right walls need to be in alignment and on the same horizontal and vertical plane.
-
If the guide rail need to be cut to match your shower opening please do it based on actual measurements. If stretch the product installation width please adjusting the insertion depth of the wall bracket to the guide rail without cutting the guide rail. DSO1 has maximum installation width stretch of 1″ for each size.
-
After the installation of the guide rail, please use the level ruler to measure whether the level.
-
After installing the rollers, hang the door on the guide rail
-
Installation of sliding glass: The height and level of the glass can be adjusted slightly by adjusting the rollers, through this adjustment can be adapted to the shower with a little wall offset, each wall offset preferably not more than 1/4″.
-
After the glass installation is completed, please measure the glass with level ruler to confirm the vertical and horizontal of the glass and then install the glass guide block.
-
Please follow the guide to install the handle and anti-jumping knobs. Anti-jumping knobs do not completely close to the guide rail, need leave slight gap to avoid sliding unsmooth.
-
The door seal can be installed according to your preference, but you need to ensure that there is minimum a wide door seal in the middle when you shower, The top of door seal needs to be slightly lower than the bottom of anti-jump knobs to avoid scraping
-
Install the anti-splash threshold according to the guidelines, please cut to the right size according to the width of your shower opening. Clean up the garbage and dry the water and stains with a soft cloth after installation,then applying the glass glue.
Note: Please
dry for 24 hours after the glass glue is applied before use.
SAFETY TIPS:
- Do not remove the glass protection corners during Installation, remove them only after installation is complete.
- Wear protective equipment when drilling, cutting rail and anti-splash threshold.
- Careful installation of the glass is required during installation, please do not step on the glass to avoid bumping.
- Wait 24 hours after installation before using the shower.
SHOWER DOOR MAINTENANCE AND CARE:
- Shower door glass i1s double-sided easy to clean glass. For daily cleaning using moist soft cloth to wipe away surface water and stains, reduce the use of cleaning agents to extend the easy-clean performance. It’s recommended to use soft cloth to clean the residual water stains on the glass after showering. Silicone squeegee is available.
- Do not use any sharp cleaning tools or cleaning agents with abrasive ingredients to clean the glass.
Please contact our customer
service to confirm the return steps before returning or get order
replacement.
Customer Service:
626-890-3620
321-946-6293
Installation Video:http://wsc.fit/Sjh
Return Address:
*16030 Phoenix Drive, City of
Industry, CA 91745
309 Dodd Blvd SE,STE 1, Rome,
GA 30161
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>