ALTA BLISS Surface Mounted Wall Switch User Guide

: June 9, 2024
: ALTA

ALTA BLISS Surface Mounted Wall Switch

Product Information

The product is a motorized shade that can be controlled using a wall switch. The user manual provides detailed instructions on how to select a channel, hide unused channels, pair/unpair wall switch, change motor direction, set upper and lower limits, and adjust limits. The motorized shade can be programmed to move up or down to the desired position and has the ability to adjust the upper and lower limits.

Product Usage Instructions

Channel Options: To select a channel, press the – button on the wall switch to select a lower channel or press the + button on the wall switch to select a higher channel.
Hide Unused Channels: To hide unused channels, press and hold (about 3 sec) – and + buttons simultaneously until the wall switch displays C (channel). Press – or + button to select the required quantity of channels (between 1 to 15). Press Stop button to confirm selection.
Getting Started: Before programming the motorized shade, ensure that the motor is turned on and ready to receive programming.
- Pair/Unpair Wall Switch: Press P1 button (about 2 sec) on the motor head until motor jog x1 and beep x1. In the next 10 secs, press and hold Stop button on the wall switch until motor jog x2 and beep x3 to pair wall switch. Repeat the same procedure to unpair wall switch
- Change Motor Direction: Press Up or Down button to check if the shade moves in the desired direction. If you need to reverse the direction, press and hold (about 2 sec) Up Motor and Down buttons simultaneously until motor jog x1 and beep x1. The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing P1 button (about 10 sec) on the motor head until motor jog x3 and beep x3.
- Setting the Upper and Lower Limits:
- Set Upper Limit: Press Up button to raise the shade, then press Stop button when it is in the desired upper limit. Press and hold (about 5 sec) Up Motor and Stop buttons simultaneously until motor jog x2 and beep x3.
- Set Lower Limit: Press Down button to lower the shade, then press Stop button when it is in the desired lower limit. Press and hold (about 5 sec) Down and Stop buttons simultaneously until motor jog x2 and beep x3.
- Adjust Limits:
- Adjust Upper Limit: Press and hold (about 5 sec) Up and Stop buttons simultaneously until motor jog x1 and beep x1. Use Up button to raise the shade to the desired highest position, and use Up or Down button to do the final adjustment if necessary.
- Adjust Lower Limit: Press and hold (about 5 sec) Up Motor and Stop buttons simultaneously until motor jog x2 and beep x3.

SPECIFICATIONS

Voltage: 1.SV(AAA)
Radio Frequency: 433.92 MHz Bi-directional
Transmitting Power: 10 milliwatt
Operating Temperature: 14°F to 122°F (-10·c to so·q
RF Modulation: FSK
Lock Function: Yes
IP Rating: IP20
Transmission Distance: up to 200m (outdoor)

SAFETY INSTRUCTIONS

Do not expose motor to humid, damp, or extreme temperature conditions.
Do not drill into motor.
Do not cut the antenna. Keep it clear from metal objects.
Do not allow children to play with this device.
If the power cable or connector is damaged, do not use.
Ensure the power cable and antenna are clear and protected from moving parts.
Cable routed through walls should be properly isolated.
Motor should be mounted in horizontal position only.
Before installation, remove unnecessary cords and disable equipment not needed for powered operation.

Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.

BUTTON INSTRUCTIONS

ALTA-BLISS-Surface-Mounted-Wall-Switch-fig-1

REPLACING THE BATTERY

a. Gently press down the cover and slide it down.
b. Install 2 AAA batteries with the+ and – ends facing correctly.
c. S lide the cover back onto the backside.

ADVANCED SETTING – DISABLE LIMIT SETTING

a. Press and hold “Stop” button more than 15s. Wall Switch will show ‘T’ (lock).
b. In the next 10s, press one “P2” button on the back of Wall Switch. Wall Switch will show •o then the Wall Switch switches to “Lock” mode to disable the following commands:
- Change Motor Direction
- Setting the Upper and Lower Limit
- Adjust Limit
- Roi ler Mode or Sheer Mode
c. Press and hold “Stop” button more than 15s. Wall Switch will show “U” (unlock).
d. In the next 10s, press one “P2” button on the back of Wall Switch. Wall Switch will show “o”. The Wall Switch now switches to “Unlock” mode, you can access all control functions.

This advanced feature is intended to be used after all shade programming is completed. User Mode will prevent accidental or unintended changing of limits.

CHANNEL OPTIONS

SELECT A CHANNEL

a. Press “-” button on the wall switch to select a lower channel.
b. Press “+” button on the wall switch to select a higher channel.

HIDE UNUSED CHANNELS

a. Press and Hold (about 3 sec) “-” and “+” buttons simultane-ously until wall switch displays “C” (channel).
b. Press “-” or “+” button to select required quantity of channel (between 1 to 15). Press “Stop” button to confirm selection (the example shows a 5-channel selection). The LED will display “O” (OK) once to confirm selection.

GETTING STARTED

It is important to confim that the motor is awake and ready to receive programming. To do this, press “Pl” button on the motor less than 1 sec, to activate the motor from Sleep Mode.

PAIR / UNPAIR WALL SWITCH

Honeycomb /Cellular and Horizontal Blind Motors DO NOT BEEP.

a. Press “P1” button (about 2 sec) on the motor head until motor jog x1 and beep x1.
b. In the next 10 secs, press and hold “Stop” button on the wall switch until motor jog x2 and beep x3.
Repeat the same procedure to unpair wall switch.

CHANGE MOTOR DIRECTION (IF NECESSARY)

Press “Up” or “Down” button to check if the shade moves in the desired direction.
If you need to reverse the direction, press and hold (about 2 sec) “Up” and “Down” buttons simultaneously until motor jog x1 and beep x1.

The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing “P1” button
(about 10 sec) on the motor head until motor jog x3 and beep x3.

SETTING THE UPPER AND LOWER LIMITS

SET UPPER LIMIT

a. Press “Up” button to raise the shade, then press “Stop” button when it is in the desired upper limit.
b. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

SET LOWER LIMIT

a. Press “Down” button to lower the shade, then press “Stop” button when it is in the desired lower limit.
b. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.
If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits.

ADJUST LIMITS

ADJUST THE UPPER LIMIT

a. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
b. Use “Up” button to raise the shade to the desired highest position, and use “Up” or “Down” button to do the final adjustment if necessary.
c. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

ADJUST THE LOWER LIMIT

a. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
b. Use “Down” button to lower the shade to the desired lowest position, and use “Up” or “Down” button to do the final adjustment if necessary.
c. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jogs x2 and beeps x3.

FAVORITE POSITION

SET FAVORITE POSITION

a. Use “Up” or “Down” button to move the shade to desired Favorite position.
b. Press and hold (about 2 sec) one “P2” button on the back of wall switch until motor jog x1 and beep x1.
c. Press and hold (about 2 sec) “Stop” button until motor jog x1 and beep x1.
d. Once more, press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.

SEND SHADE TO FAVORITE POSITION

Press and hold (about 2 sec) “Stop” button, motor will move to Favorite position.

DELETE FAVORITE POSITION

a. Press and hold (about 2 sec) one “P2” button until motor jog and beep x1.
b. Press and hold (about 2 sec) “Stop” button until motor jog and beep x1.
c. Once more, press and hold (about 2 sec) “Stop” button until motor jog x1 and long beep x1.

ROLLER MODE AND SHEER MODE

ROLLER SHADE MODE -Default mode, allows for continuous raising/lowering of shade after a short press.

a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog xl.
b. Press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.

SHEER SHADE MODE
Allows for slight adjustment after a short press and raising/ lowering of shade after a longer press.

a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog xl.
b. Press and hold (about 2 sec) “Stop” button until motor jog xl and beep xl.

ADD OR REMOVE ADDITIONAL WALL SWITCH

USING CURRENT WALL SWITCH

a. On the current wall switch, press and hold (about 2 sec) one “P2” button until motor jog x1 and beep x1.
b. Once more, on the current wall switch, press and hold (about 2 sec) one “P2” button until motor jog x1 and beep x1.
c. On the New wall switch, press and hold (about 2 sec) one “P2” button until motor jog x2 and beep x3.
Repeat the same procedure to remove additional wall switch.

NEW WALL SWITCH CONTROL
Follow instructions under the section 1. Pair / Unpair Wall Switch

ADJUST MOTOR SPEED

INCREASE MOTOR SPEED

a. Press one “P2” button until motor jog x1 and beep x1.
b. Press “Up” button until motor jog x1 and beep x1.
c. Once more, press “Up” button until motor jog x2 and beep x1.

DECREASE MOTOR SPEED

a. Press one “P2” button until motor jog x1 and beep x1.
b. Press “Down” button until motor jog x1 and beep x1.
c. Once more, press “Down” button until motor jog x2 and beep x1.

If the motor has no response, it already has a Maximum or Minimum speed.

FCC STATEMENT

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause interference, and
This device must accept any interference, including interference that may cause undesired operation of the device.

QUICK INDEX

ALTA-BLISS-Surface-Mounted-Wall-Switch-fig-19

TROUBLESHOOTING

Problem The motor has no response Cause

Battery in motor is depleted
Insufficient charging from Solar Panel Wall switch battery is discharged or not installed properly
Radio interference I shielding
Receiver distance is too far
Power failure
Incorrect wiring

Problem· The Motor beeps 10 times when In use Cause
Battery voltage is low/ SolarPanel Issue

Problem· Cannot program a slngle motor Cause
Multiple Motors are paired to the same

Solution
Recharge with compatible AC adaptor and check connection and positioning of solar panel Check connection and orientation of solar panel. Replace battery or check placement. Ensure wall switch and the antenna on the motor are positioned away from metal objects. Move wall switch to a closer position. Check power supply to motor is connected/active. Check that wiring is connected correctly.

Solution
Recharge with AC adapter or check connection and positioning of solar PV panel

(multlple motors respond) Solution
Always reserve a channel for programming.

BEST PRACTICE: Provide an extra 15 channel remote in your multi-motor projects for individual control and programming purposes
To work on a single motor at a time, place all other motors into sleep mode. Press the “Pl” button (about 6 ec) on the motor head until motor jog x2 and beep x2.