Stinger SPXDK4 Enlight10 4 Rock Light Dynamic RGB LED Kit Instruction Manual

Stinger SPXDK4 Enlight10 4 Rock Light Dynamic RGB LED Kit

Product Information

The RGB module is a lighting accessory that consists of LED pods and cables that can be connected in a daisy chain pattern. The LED pods are designed to emit colorful lights and can be mounted on any vehicle. The module comes with 4, 10 ft extensions that can be used if necessary. It is recommended to avoid mounting the module in locations that get extremely hot or wet.

Product Usage Instructions

1. Determine a location for the RGB module. Ensure that it is not mounted in locations that get extremely hot or wet.
2. For correct light pattern flow, mount each pod with the female connector end facing the front of the vehicle. The correct light flow starts from the module to each rock light.
3. Mount the LED pods using the Flat or Curved Rubber Mounting pads. Ensure that the lights are mounted in a location where they will not come in contact with suspension, tires, or road surface.
4. Route and connect the light cables to the RGB module in a daisy chain connection pattern. Make sure to avoid interference with suspension, exhaust, or any moving parts.

By following these instructions, you can install and use the RGB module to add colorful lights to your vehicle.

4 ROCK LIGHT DYNAMIC RGB LED KIT

Before you start, review directions completely. If your vehicle is not pre- wired for external lighting, you may need the following:

• In-line Fuse Holder (SPXATC16 or similar)
• 3 Amo Fuse
• 2 Strand Primary Wire
• Wire Connectors / Solder
• Wire Cover
• Zip-Ties

Optional:

• switch
• Relay

MOUNTING THE LED PODS

1. Determine a location for the RGB module There are 4, 10 ft extensions that can be used if necessary.

2. For correct light pattern flow, mount each pod with the female connector end facing the front of the vehicle.
   NOTE: The correct light flow starts from the module to each rock light. Avoid mounting the module in locations that get extremely hot or wet.

3. Mount the LED pods using the Flat or Curved Rubber Mounting pads. Lights should be mounted in a location where they will not come in contact with suspension, tires or road surface.

4. Route and connect the light cables to the RGB module in a daisy chain connection pattern making sure to avoid interference with suspension, exhaust or any moving parts.

WHAT’S INCLUDED

• 4 x SMD LED Pods
• 4 x Pod Extension Cables (IOft)
• 4 x Flat Rubber Mounting Pads
• 4 x Curved Rubber Mounting Pads
• I x Bluetooth RGB Control Module with connection for HEIGHIO
• I x RF Remote Control
• 8 x Mounting Screws

8 ROCK LIGHT DYNAMIC RGB LED KIT

Before you start, review directions completely. If your vehicle is not pre- wired for external lighting, you may need the following:

• In-line Fuse Holder {SPXATC16 or similar)
• 3AmpFuse
• 2 Strand Primary Wire
• Wire Connectors/ Solder
• WireCover
• Zip-Ties

Optional:

• Switch
• Relay

WHAT’S INCLUDED

• 8 x SMD LED Pods
• 8x Pod Extension Cables (10ft)
• 8 x Flat Rubber Mounting Pads
• 8 x Curved Rubber Mounting Pads 1 x Bluetooth RGB Control Module with connection for HEIGHlO
• 1 x RF Remote Control
• 16 x Mounting Screws

MOUNTING THE LED PODS

1. Determine a location for the RGB module There are eight 10 ft extensions that can be used if necessary.

2. For correct light pattern flow, mount each pod with the female connector end facing the front of the vehicle.
   NOTE: The correct light flow starts from the module to each rock light. Avoid mounting the module in locations that get extremely hot or wet.

3. Mount the LED pods using the Flat or Curved Rubber Mounting pads. Lights should be mounted in a location where they will not come in contact with suspension, tires or road surface.

4. Route and connect the light cables to the RGB module in a daisy chain connection pattern making sure to avoid interference with suspension, exhaust or any moving parts.

CONNECTED WITH LED STRIP

8 ROCK LIGHT KIT CONNECTED WITH LED STRIP LIGHTS AND LED WHIP LIGHTS

• Each Rock Light Pod has an Input connection and an output connection allowing you to connect other products to the same control module
• Here is a diagram showing how to connect the SPXDK8 with 2 SPXDS (Light Strips) and ending in a SPXDW4 (LED Whips)

ROCK LIGHT KIT POWER WIRING DIAGRAM

WIR ING DIAGRAMS

• Diagram 1: Wiring direct to power and using an App to turn on/off. Must add 3 AMP fuse on RED 12V+wire.

• Diagram 2: Wiring with a switch. You can add a new dedicated switch or use an existing light switch that outputs 12V+ when ON. You will need to add a 3 AMP fuse on the RED 12V+ wire and also requires a 12V relay.
  Note: When wired to a switch, the RGB controller will default to last mode/color used. No need to access the opp.

• HEIGHl0 connection: Connect the Sirius XM harness to the HEIGHlO, then connect the 4 pin male connector of the LED module to the female connector of the HEIGHlO Sirius XM harness. If your HEIGHl O is missing the harness or has the wrong connector you will need to purchase the optional harness (SE-SXMHAR)

• NOTE: Lighting module will still need separate power and ground when connecting SE-SXMHAR

GET THEAPP

Scan the QR Code, or visit Google Play or iTunes to download the Stinger Lighting opp. Once the opp is installed, power up the RGB Module and open the opp. The module should auto-connect and be listed in the device list. And Jon says Let There Be Light.

SCAN for Apple iOS and Android App

Stinger is a Power Brand of AAMP Global 15500 Lightwave, Clearwater, Florida 33760 P: 888-228-5560

• support@stingerelectronics.com
• www.stingerelectronics.com
• 2019 AAMP Global

LIMITED WARRANTY

Stinger warrants this product to be free of defects in materials and workmanship for a period of one (1 ) years from the original date Of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized Stinger dealer in the United States of America only. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Stinger will (at •ts discretion), repair or replace the defective product with new or re manufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure tofollow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty.

INTERNATIONAL WARRANTIES
Products purchased outside the United States of America are covered only by that country’s Authorized Stinger reseller and not by Stinger. Consumers needing service or warranty informa tion for these products must con act that country’s reseller for information.

When adding multiple light kits together you will need to adjust the pixel count using the enLIGHTl 0 phone app. Below are the pixel count for each part and on page 2 you will find the Steps and the Pixel Calculator.

• Each SPXDBTC has a pixel count min and max
• Minimum 30
• Maximum 1024
• Rock Lights = 4 pixels per Rock Light

For example:

• 1 SPXDK4 (4 Rock Lights} = 16 pixels. (App supports min 30 pixels)
• 1 SPXDK8 (8 Rock Lights} = 32 pixels.
• Whips and Light Strips are treated as left/right pairs so pixel count is for two units.

For example:

• 2 SPXDW4 (Whips} = 108 Pixels total.
• 2 SPXD5 (Light Strips} = 100 pixels total.
• If you were to have three or four Whips you would enter 108 x 2 = 216 pixels.
• If you were to have three or four Light Strips you would enter 100 x 2 = 200 pixels.

Product Pixel Count

Step 1.
Open the enLIGHTl O opp on your phone.

Step 2.
Open the Settings menu.

Step 3.
Click on Chasing Setting.

Step 4.
Click on the device. The device should now be highlighted in blue. If you have a kit the device name will have a preset pixel count (SPXDK4 = 30, SPXDK8 =32, SPXDUBKIT = 50).

Step 5.
Enter the number of pixels you want and press enter.

Step 6.
Go to the Mode page and turn the connected device off then on by pressing the Green icon.

Pixel Calculator

• Rock Light = 4 pixels each LED strip per 2 inches = 1 pixel For example: 12 Inch strip = 6 pixels

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>