FLOS S4 Almendra Suspension Lamp Instruction Manual
- June 9, 2024
- FLOS
Table of Contents
FLOS S4 Almendra Suspension Lamp
Product Information
The Almendra S4 is a lighting fixture designed by Patricia Urquiola in 2022 for FLOS. It comes with a 63W LED bulb and is also compatible with a 60W LED bulb. The fixture is available in different versions for different regions, including EUR, USA, DE, FR, ES, PT, RUS, J, CN, and SA. It is possible to create different configurations of the diffuser bodies in positions A-B-C-D-E-F, provided that the symmetry of the appliance is respected.
Product Usage Instructions
To install and use the Almendra S4 lighting fixture, follow the assembly
sequence shown in Fig. 1E-2E-3-4E-5-6-7-8-9-10-11-12-13-14E for EUR version
and Fig.1U-3-4U-5-6-7-8-9-10-11-12-13-14U for the USA version. Select and
employ screw anchors which are suited to the surface where the
appliance is to be installed. For IT version, choose tasseled expansion
idoneal. For RUS version, follow the instructions in Russian. For CN and SA
versions, refer to 1E-1U. Connect the black wire to black (L), white wire to
white (N), and green wire to earth (GND) as shown in Fig. 3 for the USA
version. For the EUR version, connect the black line to negative (-) and for
the USA version, connect it to positive (+) as shown in Fig. 4E and Fig. 4U
respectively. Use the junction joint and power supply joint as shown in Fig. 6
and Fig. 7 respectively. Use the terminal joint as shown in Fig. 8.
For the DALI version, use P1 and P2 to connect. The fixture is also compatible with 0-10V and 1-10V systems. Use 1x, 2x, or 3x to control the dimming level. For the EUR version, use Fig. 1E and Fig. 2E to turn the fixture on and off, and adjust the dimming level. For the USA version, use Fig. 3 to turn the fixture off, and Fig. 5 to adjust the dimming level. Refer to Fig. 5 for different configuration examples of the fixture. To create your preferred configuration, combine the diffuser bodies in positions A-B-C-D-E-F while ensuring that the symmetry of the appliance is respected.
INSTRUCTION FOR CORRECT INSTALLATION AND USE
WARNING
The safety of this fitting can only be guaranteed if these instructions are
observed, during both installation and use. Please retain these instructions
safety.
REMARKS
-
When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
-
The appliance may in no way be modified or tampered with. Any modification may compromise safety and making the appliance itself dangerous.
FLOS declines all responsibility for products that are modified. -
This appliance must be connected to an efficient grounding system in order to work safely and correctly.
-
The device carries no risk of photobiological emissions.
-
The light source cannot be replaced by the customer. Contact FLOS for information.
-
Should the external trailing cable get damaged, it must be replaced by FLOS or by qualified personne in order to avoid any danger.
-
The symbol shown on the device indicates that the product must be disposed of in a different manner than with the urban waste.
TECHNICAL DATA
- EUR: 60W LED.
- USA: 63W LED.
CLEANING INSTRUCTIONS
- Use only a soft cloth to clean the appliance, dampened with water and soap or mild cleanser if needed for resistant dirt.
- Warning: do not use alcohol or other solvents.
VERSION | Assembly Sequence |
---|---|
EUR | Fig.1E – 2E – 3 – 4E – 5 – 6 -7 – 8 – 9 – 10 – 11 – |
12 -13 -14E.
USA| Fig.1U – 3 – 4U – 5 – 6 -7 – 8 – 9 – 10 – 11 – 12
-13 -14U.
Pic.1E-1U
NOTE
Select and employ screw anchors which are suited to the surface where the
appliance is to be installed.