OLIGHT Obulb Pro S Rechargeable Multicolor Light User Manual
- June 9, 2024
- OLIGHT
Table of Contents
OLIGHT Obulb Pro S Rechargeable Multicolor Light
Product Information: Colorful and Smart Light Orb
The Colorful and Smart Light Orb is a portable lighting device that comes with a USB magnetic charging cable and an adhesive metal badge. It is equipped with both white and colored light modes, and can be controlled using the Olight Hub app. The device has a working temperature of 1.5m and weighs 105g/3.7oz. The battery capacity is 1650mAh 3.7V, and it takes around 2h30min to fully charge.
In the Box
- Light Orb
- Adhesive Metal Badge
Product Specifications
| White Light | High | 240 lumens | 100% |
|---|---|---|---|
| Low | 0.8 lumens | 100% | |
| Colored Lights (Factory Default) | MODE 1 | 10 lumens | 100% |
| MODE 2 | 10 lumens | 100% | |
| MODE 3 | 15 lumens | 100% | |
| MODE 4 | 9 lumens | 100% | |
| MODE 5 | 12 lumens | 100% | |
| MODE 6 | 4 lumens | 100% | |
| IPX7 | 1.5m Working temperature | 65*H58mm | |
| --- | --- | --- | |
| 105g/3.7oz | 1650mAh 3.7V | 2.56*H2.28in (Including Battery) | |
| 6.10Wh | |||
| Cable length | Input | Output | Time to fully charge |
| --- | --- | --- | --- |
How to Use
- Before first use, charge the product to unlock it.
- To turn on/off the device, press the button or double press the button.
- To lock/unlock the device, press and hold the button for more than 1 second.
- To turn on the low white light, press the button once.
- To change modes, press the button multiple times until you reach your desired mode.
- To change brightness, press and hold the button for more than 2 seconds.
- To apply the adhesive metal badge, refer to Figure 8 in the user manual.
- To control the device using the Olight Hub app, follow the instructions provided in the user manual.
Colorful and smart light orb
IN THE BOX
Table 1: Light Orb
Table 2: USB Magnetic charging cable
HOW TO USE THE APP
Figure 16
Auto sleep mode
If the connected Obulb Pro S is left without operation for 12 hours, it
will enter sleep mode automatically and the APP will lose control of it. To
regain control, please wake up the Obulb Pro S with any button operation or by
charging it.
Restore factory light mode
When the Obulb Pro S is in the network setting mode or is removed from the
network, it will automatically clear the memorized light mode and restore the
factory light mode. If the Obulb Pro S has not been connected within 3
minutes, it will exit the network setting mode automatically. You can also
exit the mode with any button operation on the Obulb Pro S. The APP cannot
control the Obulb Pro S if its button is locked out. Please unlock the button
to enable control.
Multi-language dictionary, see Table 3
- Product specification, see Table 1 and Table 2;
- Operating instructions as below：
- Product appearance, see Figure 1;
- Before first use, please charge the product to unlock it, see Figure 2;
- Turn on/off, see Figure 3;
- Lock/unlock, see Figure 4;
- Turn on the low white light, see Figure 5;
- Change modes, see Figure 6;
- Change brightness, see Figure 7;
- Application of adhesive metal badge, see Figure 8;
- The APP operating instructions as below:
- Download and install the APP, see Figure 9;
- Add devices, see Figure 10;
- Enter the network setting mode, see Figure 11;
- Add devices successfully, see Figure 12;
- White light/colored light control interface, see Figure 13;
- Music rhythm interface, see Figure 14;
- Planning/Interaction interface, see Figure 15;
- Tips, see Figure 16.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may
cause undesired operation.
WARNING
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following:
MEASURES
Reorient or relocate the receiving antenna. Increase the separation between
the equipment and receiver. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. Consult the dealer or
an experienced radio/TV technician for help.
FCC (IC) Radiation Exposure Statement
This equipment complies with FCC (IC) radiation exposure limits set forth
for an uncontrolled environment. The device can be used in portable exposure
condition without restriction.
WARRANTY
WITHIN 30 DAYS OF PURCHASE: Contact the original seller for repair or
replacement.
WITHIN 2 YEARS OF PURCHASE: Contact Olight for repair or replacement.
This warranty does not cover normal wear and tear, modifications, misuse,
disintegrations, negligence, accidents, improper maintenance, or repair by
anyone other than an authorized retailer or Olight itself.
USA Customer Support
cs@olightstore.com
Global Customer Support
contact@olightworld.com
Visit www.olightworld.com to see our complete
product line of portable illumination tools.
Dongguan Olight E-Commerce Technology Co., Ltd
- 4th Floor, Building 4, Kagu Industrial Park, No 6 Zhongnan Road, Chandan Town,
- Dongguan City, Guangdong, China.
- Made in China
CONTAINS FCC ID: 2ANDL-BTU
IC: 28283-OBULBPROS
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>